You can read the recommendations in the user guide, the technical guide or the installation guide for ASUS RAMPAGE IV EXTREME. You'll find the answers to all your questions on the ASUS RAMPAGE IV EXTREME in the user manual (information, specifications, safety advice, size, accessories, etc.). Detailed instructions for use are in the User's Guide. User manual ASUS RAMPAGE IV EXTREME User guide ASUS RAMPAGE IV EXTREME Operating instructions ASUS RAMPAGE IV EXTREME Instructions for use ASUS RAMPAGE IV EXTREME Instruction manual ASUS RAMPAGE IV EXTREME
Your user manual ASUS RAMPAGE IV EXTREME
Manual abstract: In this way you can still attach the motherboard to the base without worrying about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the board or cause board malfunctioning. "*" For RAMPAGE IV EXTREME only . "**" For RAMPAGE IV EXTREME Ultra only. RAMPAGE IV EXTREME Ultra/RAMPAGE IV EXTREME Motherboard -4- Chapter 1 Introduction Features Summary Form Factor CPU -- 30.5cm x 24.4cm ATX size form factor, 4 layers PCB. -- Socket 478 for Intel® Micro FC-PGA2 Pentium® 4 processor -- Support Intel ® Pentium ® 4 (Northwood, 0.13 m) processor -- -- -- -- -- -- -- -- -- -- -- -- -- -- Support Intel ® Pentium ® 4 Processor with HT Technology Intel Pentium® 4 400/533MHz FSB 2nd cache depends on CPU SiS 655 Host/Memory controller SiS 963 MuTIOL Media I/O 4 184-pin DDR DIMM sockets Supports Dual channel DDR333/DDR266 DIMM Supports 128MB/256MB/512MB/1GB unbuffered DRAM Supports up to 4GB DRAM (Max) Supports only 2. 5V DDR DIMM IT8705F 1 AGP 3.0 slot supports 8X/4X mode 5 PCI slot supports 33MHz & PCI 2.2 compliant 2 IDE controllers provides IDE HDD/CDROM (IDE1, IDE2) with PIO, Bus Master (Ultra DMA33/ATA66/ATA100/ATA133) operationmodes English Chipset Memory I/O Control Slots On-Board IDE Serial ATA ** -- IDE3 and IDE4 Compatible with RAID,Ultra ATA133/100, EIDE** -- 2 Serial ATA connectors in 150 MB/s operation mode -Controlled by Silicon Image SiI3112A to be continued "**" For RAMPAGE IV EXTREME Ultra only. -5Introduction English On-Board Peripherals -- 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1. 44M -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- and 2.88M bytes. 1 Parallel port supports Normal/EPP/ECP mode 2 Serial ports (COMA&COMB) 6 USB 2.0/1.1 ports (2 x Rear, 4 xFront by cable) 1 FrontAudio Connector 1 IrDA connector for IR CPU/System Fan Revolution detect CPU/System Fan Fail Warning CPU Overheat Warning System Voltage Detect Realtek ALC650 CODEC Line Out / 2 front speaker Line In / 2 rear speaker(by s/w switch) Mic In / center& subwoofer(by s/w switch) SPDIF out /SPDIF IN** CD In / AUX_IN / Game Port Hardware Monitor On-BoardSound On-Board RAID** -- Onboard ITE IT8212F -- Supports data striping (RAID 0) or mirroring (RAID 1) or striping+mirroring (RAID 0+RAID 1) -- Supports JBOD function -- Supports concurrent dualATA133 IDE controller operation -- SupportATAPI mode for HDD -- Supports IDE bus master operation -- Support ATA133/RAID mode switch by BIOS -- Displays status and error checking messages during boot-up -- Mirroring supports automatic background rebuilds -- Features LBA and Extended Interrupt 13 drive translation in controller onboard BIOS -- Build in RTL8101L Chipset -- 1 RJ45 port -- PS/2 Keyboard interface and PS/2 Mouse interface to be continued On-Board LAN** PS/2 Connector "**" For RAMPAGE IV EXTREME Ultra only. RAMPAGE IV EXTREME Ultra/RAMPAGE IV EXTREME Motherboard -6- BIOS AdditionalFeatures -- Licensed AWARD BIOS, 2M bit Flash ROM -- -- -- --- -- -- -- Supports Dual BIOS** / Q-Flash PS/2 Keyboard power on by password PS/2 Mouse power on STR(Suspend-To-RAM) AC Recovery USB KB/Mouse wake up from S3 Poly fuse for keyboard over-current protection Supports EasyTune 4 English Overclocking -- Supports @BIOS -- Over Voltage (CPU/DRAM/AGP) by BIOS HT functionality requirement content "Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components: - CPU: An Intel® Pentium 4 Processor with HT Technology - Chipset: An SiS® Chipset that supports HT Technology - BIOS: A BIOS that supports HT Technology and has it enabled - OS: An operation system that has optimizations for HT Technology Please set the CPU host frequency in accordance with your processor's specifications. We don't recommend you to set the system bus frequency over the CPU's specification because these specific bus frequencies are not the standard specifications for CPU, chipset and most of the peripherals..
Your user manual ASUS RAMPAGE IV EXTREME
Powered by TCPDF (www.tcpdf.org) 