Free Essay

Diy Magnetic Generator

In:

Submitted By jimenezgaby
Words 1435
Pages 6
Permanent Magnetic Generator Construction Manual

http://HoJoMotor.com

Our Team Doing an On-site Assembly in Peru

http://HoJoMotor.com

Section 1) Introduction
This manual describes how to build a 'permanent magnet generator' (PMG). We can also call it an 'alternator', because it generates alternating current (AC). It will not generate 'mains voltage' or 'utility power' AC. It generates low voltage, 'three phase' AC, and then changes it into 'direct current' (DC) for charging a 12 volt battery. What this PMG is made of

1) EXPLODED PMG The PMG (see diagram 1) consists of: • • • • A steel spine and shaft. A stator containing coils of wire Two magnet rotors A rectifier

The stator contains six coils of copper wire, cast in fiberglass resin. This stator casting is mounted onto the spine; it does not move. Wires from the coils take electricity to the rectifier, which changes the AC to DC for charging the battery. The rectifier is mounted on an aluminum 'heatsink' to keep it cool.

http://HoJoMotor.com

The magnet rotors are mounted on bearings, which turn on the shaft. The rear rotor is behind the stator, and enclosed within it. The front one is on the outside, fixed to the rear one by long studs which pass through a hole in the stator. The wind turbine rotor blades will be mounted on the same studs. They will turn the magnet rotors, and move the magnets past the coils. Magnetic flux passes from one rotor to the other through the stator. This moving magnetic flux is what produces the electric power.

Continued on next page…

http://HoJoMotor.com

Building the PMG (Permanent Magnetic Generator) This manual describes how to build the PMG. Read right through it before starting. Section 2 List of materials and tools for the job Section 3 explains how to build the special tools (called jigs) and the moulds which are needed. You can build more than one PMG with them. There are many possible ways to make these jigs and moulds, but there is only room in this manual to describe one way to do it. Section 4 is about the stator. It describes how to wind the coils of enameled copper wire, and cast them in resin, using the jigs and moulds. Section 5 shows how to build the magnet rotors, using magnet blocks and steel disks, set in another resin casting. Section 6 shows how to assemble the parts into a whole PMG. It explains how to build the mechanical parts, how to balance the rotors, and what is required to connect the wiring from the stator. Section 7 is about testing the PMG. It contains procedures for checking that it is correctly balanced and ready to use. It describes the options for connecting up the electrical output. It also explains how to connect the PMG to the battery. Section 8 contains additional information about the use of polyester resins, and about using the PMG for hydro power. What this PMG can do This PMG is made for small wind generators (see diagram 2). To build a complete wind generator, you also need • • • • a a a a tower : perhaps a steel pipe, supported with guy ropes, 'yaw head' swiveling on the tower top, tail, to keep it facing towards the wind, set of blades, to turn it.

The spine of the PMG bolts on to the yaw head. The blade assembly fits on to the front of the PMG. The yaw head and tail need to be so constructed that the wind generator will turn from strong winds, to protect itself. (This manual does not describe the blades, tower, or yaw head.)

http://HoJoMotor.com

2. WIND TURBINE

The PMG works at low rotational speed. The chart shows the power output of the PMG, charging a 12 volt battery. At 420 rpm it generates 180 watts, which is 15 amps at 12 volts (15A x 12V = 180W). At higher speed, the PMG can generate more power. But high currents cause the coils to heat up, and so the efficiency gets worse as the output current gets higher. For higher speed it is better to change the stator coils, either by using different size wire, or by changing the way they are connected. If the PMG is always used at higher speeds, it is better to use thicker wire, which can carry more current without getting so hot. Using thicker wire means there are fewer turns on the coils, which means that the PMG would not work at low speed. To use the same PMG for both low and high speeds, it is possible to change the connections. There are two ways to connect the stator wires to the rectifier. They can be connected 'star' or 'delta'. See Section 7 for a detailed description of the star and delta connections. See diagram 3 for the graph of power vs. speed. Star begins to work at low speed (170 rpm). Delta gives more power, but only at higher speed. Star is good in very low windspeeds, and delta is better in higher winds.

http://HoJoMotor.com

A bigger version of this PMG would be able to give higher power at lower speed. 3. GRAPH OF POWER VS. SPEED

Caution Take care when building and assembling the PMG so that the magnets cannot come loose. This can happen under extreme circumstances. Loose magnets rubbing on the stator can then destroy the PMG. • Follow all the instructions for casting the magnet rotors - do not simply glue the magnets to the steel disks. • Do not hit the magnet rotors with hammers during assembly. • Take care that there is at least 1mm gap clearance between the magnets and the stator, on both sides. (For heavy duty, or high speed, use a larger gap.) • Do not run the PMG at speeds faster than 800 rpm on a wind turbine. (When the wind turbine yaws, large gyroscopic forces will flex the shaft, and the magnets may touch.) • Do not mount the rotor blade assembly directly onto the front magnet rotor disk, at any point away from the studs. Mount it only onto the studs and nuts themselves, which come through the disk.

http://HoJoMotor.com

• When mounting the PMG on the wind turbine yaw mount, keep the box section 'spine' of the PMG vertically upright, and not horizontally cross-wise.

2. List of Materials and tools

http://HoJoMotor.com

Materials for moulds and jigs Composite floorboards (other ideas are possible) and wood glue Sand paper, wax polish (Polyurethane varnish, and PVA release agent, if available.) Paint brushes, and thinners to clean them 13mm Plywood for jigs and formers and stator mould centre Steel rod, or pipe, for coil winding machine Small pieces of steel plate or thick sheet metal

Tools Safety goggles, face mask, gloves, etc. as required Workbench with vice Welder Angle grinder Hacksaw, hammer, punch, chisel Compasses, tape measure, angle gauge. Spanners: 8, 10, 13, 17, 19mm : two of each. Tap wrench and M10 taps for outer holes in magnet rotors. Brass wire to gauge the heights of magnets Pillar Drill Press Drill bits 6,8,10,12mm Holesaws 25mm, 65mm Wood lathe, or a substitute as in Section 3 Chisel for wood lathe Jigsaw to cut wood Scales to weigh resin. Dispenser for catalyst, plastic buckets, scissors. Soldering iron, resin-cored solder, wire cutters, sharp knife.

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

http://HoJoMotor.com

We hope you found this guide extremely helpful and that the step by step nature of this guide helps you build your own permanent Magnetic Generator. We know you can do this because so many others already have! Good luck to you.

**Also, if you’re interested in producing free energy from a wind turbine…or solar panels:

Click Here To Get a Wind Energy Guide
Or go to:

http://HoJoMotor.com/go/wind-energy.php

http://HoJoMotor.com

Similar Documents

Premium Essay

Oil Conservation

...ole of youth in oil conservation ”Under your shoulders. Dear young people of the entire world, weigh the responsibility to transform tomorrow's world into a society where peace, harmony and fraternity reign. “ - Bishop Carlos Belo Youth constitute about 40 percent of the total population of India. The youth of every country is its valuable human resource. The responsibility for change, progress and innovation lies on their shoulders. Youth can make or mar society. There has always been misunderstood by the elders. The elders feel that, being immature and inexperienced, the youth usually indulge in thoughtless activities. However, the youth have the zeal to initiate revolutions. Mao Tse Tung of China realized this latent power and dedication of youth of his country. He entrusted them with the responsibility of bringing   about Cultural Revolution, a change in the attitude of the society. The youth of our country also played a significant role in the freedom struggle. Today the youth needs to play an important role in promoting oil conservation. India is country of rich cultural heritage as well as it is rich in resources essential for a comfortable living. Such resources also include the oil resources such as petroleum and diesel which are essential resources for transportation but these resources are exploited today to extreme. Conservation of these resources is necessary so as to enjoy and live life comfortably. As Mahatma Gandhi said “the earth has enough to fulfill the...

Words: 9262 - Pages: 38

Free Essay

Ic 555

...How IC 555 timer works? Fundamentals of IC 555 timer & its basic applications VSagar • December 16, 2011 This article was first written on 16 Dec. 2011 and now it is rewritten in simple language with more practical approach, due to huge demand from visitors. Pin-wise functioning of IC555 timer Pin-1, GROUND: It is the GROUND PIN of the IC. The negative terminal of DC power supply or battery is connected to this pin. Here note that IC555 works always on single rail power supply and NEVER on dual power supply, unlike operational amplifiers. Also note that this pin should be connected directly to ground and NOT through any resistor or capacitor. If done so, the IC will not function properly and may heat up and get damaged. This happens because all the semiconductor blocks inside the IC will be raised by certain amount of stray voltage and will damage the IC. Refer the block diagram of the IC for more details. For more details read elaborate collection of FAQ on this IC. Pin-2, TRIGGER It is known as TRIGGER PIN. As the name suggests in triggers i.e. starts the timing cycle of the IC. It is connected to the inverting input terminal of trigger comparator inside the IC. As this pin is connected to inverting input terminal, it accepts negative voltage pulse to trigger the timing cycle. So it triggers when the voltage at this pin LESS THAN 1/3 of the supply voltage (Vcc). In number of applications, the IC must be triggered by a pulse. The amplitude and minimum pulse width...

Words: 6051 - Pages: 25

Premium Essay

Save Days

...BMW 3- & 5-Series Service and Repair Manual A K Legg Models covered 3-Series (E30) 316 (83 to 88), 316i (88 to 91), 318i (83 to 91), 320i (87 to 91), 325i (87 to 91). Also Touring and Convertible versions of these models 5-Series (E28) 518 (81 to 85), 518i (85 to 88), 525i (81 to 88), 528i (81 to 88), 535i (85 to 88), M535i (85 to 88) 5-Series (E34) 518i (90 to 91), 520i (88 to 91), 525i (88 to 91), 530i (88 to 91), 535i (88 to 91) Engines covered 1596 cc, 1766 cc, 1795 cc, 1990 cc, 2494 cc, 2788 cc, 2986 cc & 3430 cc Does not cover Diesel, dohc or V8 engines, or four-wheel-drive models LAE MIMI and Larry Warren (1948-256-11AA3) © Haynes Publishing 1997 A book in the Haynes Service and Repair Manual Series ABCDE FGHIJ KLMNO PQRST 123 Printed by J H Haynes & Co. Ltd, Sparkford, Nr Yeovil,Somerset BA22 7JJ, England Haynes Publishing Sparkford, Nr Yeovil, Somerset BA22 7JJ, England Haynes North America, Inc 861 Lawrence Drive, Newbury Park, California 91320, USA Editions Haynes S.A. 147/149, rue Saint Honoré, 75001 PARIS, France Haynes Publishing Nordiska AB Box 1504, 751 45 Uppsala, Sweden All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage or retrieval system, without permission in writing from the copyright holder. ISBN 1 85960 236 3 British Library Cataloguing in Publication Data A catalogue record for this book is...

Words: 146734 - Pages: 587

Premium Essay

Retailing in India

...CONSUMER BEHAVIOUR IN THE INDIAN RETAIL SECTOR CONSUMER BEHAVIOUR IN THE INDIAN RETAIL SECTOR PROJECT REPORT ON Submitted By PATHAN SHAHID KHAN UNDER THE GUIDANCE OF Prof. Rafana Kazi in partial fulfilment for the award of the degree of MMS Anjuman-I-Islam’s Allana Institute of Management Studies Mumbai 400 001 2014-15 APPENDIX 1 Anjuman-I-Islam’s Allana Institute of Management Studies Badruddin Tyabji Marg, OFF. 92, Dr. D.N. Road, Opp. CST, Mumbai 400 001 Certificate This is to certify that Pathan Shahid Zuber Khan, a student of Anjuman-I-Islam’s Allana Institute of Management Studies (AIAIMS) pursuing final year in MMS has completed the dissertation report on Market analysis of LG consumer durables in the 2014-15 Date:__________________ Place:__________________ _____________________Prof. Rafana KaziProject GuideAIAIMS | ________________________Dr. Lukman PatelDirectorAIAIMS | DECLARATION Project Title: Market analysis of LG consumer durables Submitted on: Under the Guidance of: Prof. Rafana Kazi College: Allana Institute of Management Studies (AIAIMS) This is to declare that I, Pathan Shahid Khan, student of Allana Institute of Management Studies (AIAIMS) IVth semester (Marketing) hereby declare that I have completed the project on Market analysis of LG consumer durables in the Academic year 2015 The information submitted is true and original to the best of my knowledge. Date: <Date of Submission> Place: Mumbai (SIGNATURE) Pathan Shahid...

Words: 14895 - Pages: 60

Premium Essay

Monicah

...Windows Server® 2008 FOR DUMmIES ‰ by Ed Tittel and Justin Korelc Windows Server® 2008 For Dummies® Published by Wiley Publishing, Inc. 111 River Street Hoboken, NJ 07030-5774 www.wiley.com Copyright © 2008 by Wiley Publishing, Inc., Indianapolis, Indiana Published by Wiley Publishing, Inc., Indianapolis, Indiana Published simultaneously in Canada No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, scanning or otherwise, except as permitted under Sections 107 or 108 of the 1976 United States Copyright Act, without either the prior written permission of the Publisher, or authorization through payment of the appropriate per-copy fee to the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, (978) 750-8400, fax (978) 646-8600. Requests to the Publisher for permission should be addressed to the Legal Department, Wiley Publishing, Inc., 10475 Crosspoint Blvd., Indianapolis, IN 46256, (317) 572-3447, fax (317) 572-4355, or online at http:// www.wiley.com/go/permissions. Trademarks: Wiley, the Wiley Publishing logo, For Dummies, the Dummies Man logo, A Reference for the Rest of Us!, The Dummies Way, Dummies Daily, The Fun and Easy Way, Dummies.com, and related trade dress are trademarks or registered trademarks of John Wiley & Sons, Inc. and/or its affiliates in the United States and other countries, and may not be used without written permission...

Words: 139691 - Pages: 559

Premium Essay

Server 2008 for Dummies

...Windows Server® 2008 FOR DUMmIES ‰ by Ed Tittel and Justin Korelc Windows Server® 2008 For Dummies® Published by Wiley Publishing, Inc. 111 River Street Hoboken, NJ 07030-5774 www.wiley.com Copyright © 2008 by Wiley Publishing, Inc., Indianapolis, Indiana Published by Wiley Publishing, Inc., Indianapolis, Indiana Published simultaneously in Canada No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, scanning or otherwise, except as permitted under Sections 107 or 108 of the 1976 United States Copyright Act, without either the prior written permission of the Publisher, or authorization through payment of the appropriate per-copy fee to the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, (978) 750-8400, fax (978) 646-8600. Requests to the Publisher for permission should be addressed to the Legal Department, Wiley Publishing, Inc., 10475 Crosspoint Blvd., Indianapolis, IN 46256, (317) 572-3447, fax (317) 572-4355, or online at http:// www.wiley.com/go/permissions. Trademarks: Wiley, the Wiley Publishing logo, For Dummies, the Dummies Man logo, A Reference for the Rest of Us!, The Dummies Way, Dummies Daily, The Fun and Easy Way, Dummies.com, and related trade dress are trademarks or registered trademarks of John Wiley & Sons, Inc. and/or its affiliates in the United States and other countries, and may not be used without written permission...

Words: 139691 - Pages: 559

Premium Essay

Nature of the Hospitality Industry

...Introduction to Hospitality Industry UNIT 1 1.1 1.2 1.3 Meaning and definition Historical evolution and development Hospitality as an Industry 1.1 Introduction Meaning and definition Tourism is not just about the facilities and attractions provided for visitors. It is about people and especially about the relationship between the customer and the individual providing service. Everybody employed in tourism needs to have the knowledge, skills and attitudes to provide the standard of product and service that customers expect. Knowing about the tourism industry, its component parts and especially where you fit in is an important starting point to a successful career in tourism. What Is Tourism? Tourism may be described as the activities of tourists and those who cater for them. It is a highly diversified business with many component parts ranging from airlines to hotels. Tourism is concerned with providing:       Travel and transport facilities Accommodation Food and drink Entertainment/recreation Information and assistance Souvenirs Above all, tourism is a hospitality industry providing a service to visitors in a warm and welcoming way. ICHM Page 1 Introduction to Hospitality Industry Who Are Tourists? Tourists are people who for a variety of reasons travel to destinations, where they stay at least one night. Excursionists are also visitors that do not make an over-night stop, such as daytrippers or people on cruises. There are several basic types of tourists:   ...

Words: 40041 - Pages: 161

Free Essay

Green

...No. Nama Perguruan Tinggi AKADEMI AKUNTANSI PGRI JEMBER Nama Pengusul Sisda Rizqi Rindang Sari Program Kegiatan Judul Kegiatan 1 PKMK KUE TART CAENIS ( CANTIK, ENAK DAN EKONOMIS) BERBAHAN DASAR TAPE 2 AKADEMI FARMASI KEBANGSAAN Nensi MAKASSAR AKADEMI KEBIDANAN CITRA MEDIKA SURAKARTA AKADEMI KEBIDANAN GIRI SATRIA HUSADA AKADEMI KEPERAWATAN KERTA CENDIKA SIDOARJO AKADEMI KEPERAWATAN KERTA CENDIKA SIDOARJO AKADEMI KEPERAWATAN KERTA CENDIKA SIDOARJO Putri Purnamasari PKMK LILIN SEHAT AROMA KURINDU PANCAKE GARCINIA MANGOSTANA ( PANCAKE KULIT MANGGIS ) 3 PKMK 4 Latifah Sulistyowati PKMK Pemanfaatan Potensi Jambu Mete secara Terpadu dan Pengolahannya sebagai Abon Karmelin (Karamel Bromelin) : Pelunak Aneka Jenis Daging Dari Limbah Nanas Yang Ramah Lingkungan, Higienis Dan Praktis PUDING“BALECI”( KERES) MAKANAN BERSERATANTI ASAM URAT 5 Achmad PKMK Zainunddin Zulfi 6 Dian Kartika Sari PKMK 7 Radita Sandia PKMK Selonot Sehat (S2) Diit untuk Penderita Diabetes 8 AKADEMI PEREKAM Agustina MEDIK & INFO KES Wulandari CITRA MEDIKA AKADEMI PEREKAM MEDIK & INFO KES Anton Sulistya CITRA MEDIKA AKADEMI PEREKAM Eka Mariyana MEDIK & INFO KES Safitri CITRA MEDIKA AKADEMI PEREKAM MEDIK & INFO KES Ferlina Hastuti CITRA MEDIKA AKADEMI PEREKAM Nindita Rin MEDIK & INFO KES Prasetyo D CITRA MEDIKA AKADEMI PEREKAM MEDIK & INFO KES Sri Rahayu CITRA MEDIKA AKADEMI PERIKANAN YOGYAKARTA PKMK Kasubi Wingko Kaya Akan Karbohidrat...

Words: 159309 - Pages: 638

Premium Essay

Problem Solving for Manager

...Creative Problem Solving for Managers Second edition How can managers tackle complex problems? How do you encourage innovation? How do you implement new solutions? Is creativity the key to management success? This accessible text provides a lively introduction to the essential skills of creative problem solving. Using extensive case studies and examples from a variety of business situations, Creative Problem Solving for Managers explores a wide range of problem solving theories and techniques, illustrating how these can be used to solve a multitude of management problems. Thoroughly revised and redesigned, this new edition retains the accessible and imaginative approach to problem solving skills of the first edition. Features include: ■ ■ ■ ■ ■ Blocks to creativity and how to overcome them Key techniques including lateral thinking, morphological analysis and synectics Computer-assisted problem solving Increased coverage of group problem solving techniques New website containing in-depth cases and a PowerPoint presentation As creativity is increasingly being recognised as a key skill for successful managers, this book will be welcomed as a readable and comprehensive introduction for students and practising managers alike. Tony Proctor is Professor in Marketing at Chester University College Business School and was formerly Senior Lecturer in Marketing and Head of the Department of Management at Keele University. Creative Problem Solving for Managers Developing skills...

Words: 109777 - Pages: 440

Premium Essay

Holly Farm

...Robert Johnston Stuart Chambers Christine Harland Alan Harrison Nigel Slack Cases in Operations Management third edition Cases in Operations Management We work with leading authors to develop the strongest educational materials in operations management, bringing cutting-edge thinking and best learning practice to a global market. Under a range of well-known imprints, including Financial Times Prentice Hall, we craft high quality print and electronic publications which help readers to understand and apply their content, whether studying or at work. To find out more about the complete range of our publishing, please visit us on the World Wide Web at: www.pearsoneduc.com THIRD EDITION Cases in Operations Management Robert Johnston Warwick Business School, University of Warwick Stuart Chambers Warwick Business School, University of Warwick Christine Harland School of Management, University of Bath Alan Harrison Cranfield School of Management, Cranfield University Nigel Slack Warwick Business School, University of Warwick Pearson Education Limited Edinburgh Gate Harlow Essex CM20 2JE United Kingdom and Associated Companies throughout the world Visit us on the World Wide Web at: www.pearsoned.co.uk First published 1993 Second published 1997 Third Edition 2003 © Robert Johnston, Stuart Chambers, Christine Harland, Alan Harrison and Nigel Slack 1993, 2003 The rights of Robert Johnston, Stuart Chambers, Christine Harland, Alan Harrison...

Words: 207956 - Pages: 832

Premium Essay

Six Sigma

...IIBM Institute of Business Management Marketing Management www.iibmindia.in Subject: MARKETING MANAGEMENT Credits: 4 SYLLABUS Concepts of Marketing Management: Definition and Concepts: Definitions of Marketing, Scope of Marketing; Core Marketing Concepts: Concept of Demand and Supply; Transaction; Major Marketing Management Philosophy; Social Marketing Marketing Environment - Internal & External Marketing Environment Forces; Macro Environment; Micro and Internal Environment; Factors Influencing Consumer Buyer Behavior; Buyer Decision Process; Inputs for Buying Decision Process; Consumer Trends; Market Segmentation Process. Developing Market Strategies and the Offerings Part –I Positioning and Differentiation: Concept, Positioning according to Ries and Trout, Various Tools of Differentiation; Product Decisions and Strategies; Product Mix; Product Life Cycle; Brand Positioning; Brand Identity; Equity and Packaging. Developing Market Strategies and the Offerings - Part II: Introduction to Service Marketing; Differentiating Services; Product and Service Price; Response to Change in Price; Pricing Strategies. Delivering Marketing Programs – Part I Marketing through Channel Partners; Wholesalers and Retailers: Current Trend; Channel Management. Delivering Marketing Programs – Part II Market Communication, Process for Effective Communication; Advertising; Different Advertising Media; Sales Promotion; Public Relations; Direct Marketing; Personal Selling:...

Words: 96487 - Pages: 386

Free Essay

500 Extraordinary Islands

...500 extraordinary islands G R E E N L A N D Beaufort Sea Baffin Bay vi Da i tra sS t a nm De it Stra rk Hudson Bay Gulf of Alaska Vancouver Portland C A N A D A Calgary Winnipeg Newfoundland Quebec Minneapolis UNITED STATES San Francisco Los Angeles San Diego Phoenix Dallas Ottawa Montreal ChicagoDetroitToronto Boston New York OF AMERICA Philadelphia Washington DC St. Louis Atlanta New Orleans Houston Monterrey NORTH AT L A N T I C OCEAN MEXICO Guadalajara Mexico City Gulf of Mexico Miami Havana CUBA GUATEMALA HONDURAS b e a n Sea EL SALVADOR NICARAGUA Managua BAHAMAS DOMINICAN REPUBLIC JAMAICA San Juan HAITI BELIZE C a r PUERTO RICO ib TRINIDAD & Caracas N TOBAGO A COSTA RICA IA M PANAMA VENEZUELA UYANRINA H GU C U G Medellín A PAC I F I C OCEAN Galapagos Islands COLOMBIA ECUADOR Bogotá Cali S FR EN Belém Recife Lima BR A Z I L PERU La Paz Brasélia Salvador Belo Horizonte Rio de Janeiro ~ Sao Paulo BOLIVIA PARAGUAY CHILE Cordoba Santiago Pôrto Alegre URUGUAY Montevideo Buenos Aires ARGENTINA FALKLAND/MALVINAS ISLANDS South Georgia extraordinary islands 1st Edition 500 By Julie Duchaine, Holly Hughes, Alexis Lipsitz Flippin, and Sylvie Murphy Contents Chapter 1 Beachcomber Islands . . . . . . . . . . . . . . . 1 Aquatic Playgrounds 2 Island Hopping the Turks & Caicos: Barefoot Luxury 12 Life’s a Beach 14 Unvarnished & Unspoiled 21 Sailing...

Words: 249855 - Pages: 1000

Premium Essay

Acca F1 Text Book

...FAB PAPER F1 ACCOUNTANT IN BUSINESS BPP Learning Media is the sole ACCA Platinum Approved Learning Partner – content for the FIA and ACCA qualifications. In this, the only FAB/F1 Study Text to be reviewed by the examiner:  We highlight the most important elements in the syllabus and the key skills you will need  We signpost how each chapter links to the syllabus and the study guide  We provide lots of exam focus points demonstrating what the examiner will want you to do  We emphasise key points in regular fast forward summaries  We test your knowledge of what you’ve studied in quick quizzes  We examine your understanding in our exam question bank  We reference all the important topics in our full index BPP’s Practice & Revision Kit and i-Pass products also support this paper. Note FIA FAB and ACCA Paper F1 are examined under the same syllabus and study guide. FOR EXAMS FROM FEBRUARY 2014 TO AUGUST 2015 I N T E R A C T I V E T E X T FAB/F1 ACCOUNTANT IN BUSINESS First edition March 2011 Third edition September 2013 ISBN 9781 4453 7026 2 Previous ISBN 9781 4453 9965 2 eISBN 9781 4453 7061 3 British Library Cataloguing-in-Publication Data A catalogue record for this book is available from the British Library Published by BPP Learning Media Ltd BPP House, Aldine Place 142-144 Uxbridge Road London W12 8AA www.bpp.com/learningmedia Printed in the United Kingdom by RICOH Ricoh House Ullswater Crescent Coulsdon CR5 2HR A note about copyright Dear Customer...

Words: 210642 - Pages: 843

Premium Essay

From Pmbok

...Project Management Project and Programme Management Resources for Students Gower have teamed up with a major provider of project management training, ESI International, to bring you a range of project and programme resources to support your learning. Visit www.projectmanagement9.com and: • • • • Download white papers on topics as diverse as the project communication, project leadership, risk management and project troubleshooting. View professional project webinars from some of the leading presenters on project management covering topics such as: risk management, troubled project recovery, portfolio management, business requirements, earned value management, performance-based service contracting. Learn about the qualifications and development available from the PMI, Project Management Institute, the world’s largest non-profit professional association in project management. Link to further resources, professional bodies, news sites and more. These resources are designed to help you develop your learning on project management and start you on the road to professional qualifications or further development, once you have finished your degree or your current qualification. Visit www.projectmanagement9.com Project Management Ninth Edition DENNIS LOCK © Dennis Lock 2007 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise...

Words: 232485 - Pages: 930

Premium Essay

Customer Relationship Management

...Customer Relationship Management VSF This book is dedicated to my children Emma and Lewis of whom I am enormously proud. Customer Relationship Management Concepts and Technologies Second edition Francis Buttle AMSTERDAM • BOSTON • HEIDELBERG • LONDON • NEW YORK • OXFORD PARIS • SAN DIEGO • SAN FRANCISCO • SINGAPORE • SYDNEY • TOKYO Butterworth-Heinemann is an imprint of Elsevier Butterworth-Heinemann is an imprint of Elsevier Linacre House, Jordan Hill, Oxford OX2 8DP 30 Corporate Drive, Suite 400, Burlington, MA 01803, USA First edition 2009 Copyright © 2009, Francis Buttle Published by Elsevier Ltd. All rights reserved. The right of Francis Buttle to be identified as the author of this work has been asserted in accordance with the Copyright, Designs and Patents Act 1988 No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise without the prior written permission of the publisher. Permissions may be sought directly from Elsevier’s Science & Technology Rights Department in Oxford, UK: phone ( 44) (0) 1865 843830; fax: ( 44) (0) 1865 853333; email: permissions@elsevier.com. Alternatively you can submit your request online by visiting the Elsevier web site at http://elsevier.com/locate/ permissions, and selecting Obtaining permission to use Elsevier material. Notice No responsibility is assumed by the publisher for any injury and/or damage...

Words: 171161 - Pages: 685