...type of automobile, car manufacturers in United States of America started to manufacture their own subcompact cars. The current president of Ford at that time, Lee Iacocca, recognized the market potential for this design of vehicles; he then led the designing of Ford’s first subcompact model car, namely Pinto on the year 1968. Due to the competition from various domestic and international automobile companies, Ford was influenced to accelerate the production of their first subcompact car. After for only 25 months of designing and manufacturing of the vehicle instead of a typical time frame of 43 months, Ford Pinto first debuted into the automotive industry as a two-door sedan with the entry model price at $1850 and followed by a hatchback and wagon version of the car later in 1972. The short time frame of the car from being a conception to the production surely raised some doubt among the sceptical during that time. Nevertheless, Ford Motor Company was still eager to market the car since it was a trend at the time. During the first few years Ford Pinto was introduced to the world, the sales were remarkable. By January 1971, the Pinto had sold over 100,000 units and 352,402 for the entire 1971 production run. 1974 saw the most Pintos produced in a single model year with 544,209 units (“Ford Pinto,” 2015). However, during mid-1970’s, Ford Pinto was surrounded by numerous controversies due to several accidents involving the car. The first accident occurred in 1972 involving a Lily...
Words: 2403 - Pages: 10
...Ford Pinto: An Ethical Inferno Michael W. Daniels Excelsior College Introduction and Analysis “Pinto crashes caused the death and mutilation of 900 occupants after their cars burst into flames after rear-end collisions,” Robert Sherefkin explains in his article Lee Iacocca's Pinto: A fiery failure. The engineered design of the Ford Pintos resulted in the gas tank rupturing in low speed rear end collisions. The design flaw was recognized early in the Ford Pinto’s production. According to Dowie’s article Pinto Madness. Mother Jones, “Internal company documents in our possession show that Ford has crash-tested the Pinto at a top secret site more than 40 times and that every test made at over 25 mph without special structural alteration of the car has resulted in a ruptured fuel tank.” Dowie then explains how more than a quarter of those tests were performed prior to the initial release of the vehicle. It was estimated that just 11$ upgrade per vehicle would have remedied the problem (Dowie, 1977). On June 10, 1978, almost a decade after the first Pinto was built, Ford eventually agreed to recall the Pinto (Boyce, D, 2012). The decision was made after countless lawsuits over a span of eight years drained the Ford Motor Company of millions of dollars. The company’s President Lee Iacocca could have rectified the design flaw but deemed it too late in production to reconstruct the vehicle. His requirement of the car weighing less than 2000 pounds and cost of under...
Words: 922 - Pages: 4
...Managing Product Safety: the Ford Pinto Summary: Around 1967 Ford Motor Company decided to design a small size car called the Ford Pinto. The automobile industry at the time (and still is) was highly competitive and very cyclical. In the late 1960's, America began to see the influences of foreign vehicles. Facts Around 1967 Ford Motor Company decided to design a small size car called the Ford Pinto. The automobile industry at the time (and still is) was highly competitive and very cyclical. In the late 1960's, America began to see the influences of foreign vehicles. Prior to that, cars were bigger and less fuel efficient, allowing the Japanese to gain substantial market share with the smaller, more economical vehicles, and the need to react to this pressure was even greater at Ford. Even though they held the number two spot in market share behind General Motors, they only held a 22.3% market share compared to General Motors at 46.4%, a very significant difference. There was strong competition for Ford in the American small-car market from Volkswagen and several Japanesecompanies in the 1960's. In order for Ford to stay competitive and fight off competition, they rushed its newest car the Ford Pinto into production in much less time than is usually required to develop a car. The regular time to producean automobile was 43 months; Ford took only 38 months. Before production, the engineers at Ford discovered a major flaw in the cars' design. In nearly all rear-end crash test...
Words: 2593 - Pages: 11
...Running head: FORD PINTO CASE STUDY PAPER Ford Pinto Case Study Paper Learning Team B University of Phoenix MGT /216 Organizational Ethics and Social Responsibility SB09BSB10 Leatricia Cash June 2, 2010 The ethical issues surrounding Ford Motors in regard to the company’s production and release of the Ford Pinto brought the integrity of the organization into question by internal and external shareholders in the 1970s (Engineering.com, n.d.). Understanding the various ethical dilemmas faced by personnel who helped with the design and build of the Pinto provides clarification as to why the organization’s reputation as a quality supplier of automobiles was put into question by consumers. Analyzing the Ford Pinto Case Study, the following information will contain an outside viewpoint in regard to the Ford Pinto case that will illustrate viewpoints on the issue based off personal perspective. A recommendation on dealing with the issues Ford Motors faced with the Pinto are provided to illustrate the ethical approach Ford could have used during the production phase and after the vehicle entered the consumer market. The recommendation will be backed by examples of external and internal social pressures that have influenced the decision to recall the Ford Pinto. In addition, the evaluation of this case during 1971 and in current day is illustrated in the readings to compare and contrast the situation based on the...
Words: 964 - Pages: 4
...Running Head: CASE STUDY Case Study Team MGT/216 09/13/10 Teacher Abstract Take a step back into the past, 1971 to be exact, imagine being a proud new owner of a popular and affordable vehicle, the Pinto. The vehicle is perfect for the tight budgeted and built by a trusted company (Ford). Then the unexpected happens, it is in a rear end accident. Upon the accident the car explodes. Sounds like a bad dream, right! (See video link in PowerPoint presentation) The following discusses a similar story that will from here forward be in reference as the Pinto Case, in which Ford was accused of being at fault for selling a shoddy car to the public. Were they at fault? What was the ethical dilemma? What were the social pressures? All of this and more is here within in detail. Pinto Case Study When Ford Motor Company had to determine what action to take in regards to the pinto many considerations were made. The company had to decide whether to install a baffle on the Ford Pinto to prevent the possibility of a puncture in the gas tank by a bolt from the bumper. The issue was found during a test done after the car was in production and on sale in the U.S. The gas tank is in the back of the car. During a rear-end test it was found that if a car travels more than 20 miles per hour and is hit from behind it is possible that a bolt from the bumper can puncture the gas tank. This can cause an explosion. Ford had the choice...
Words: 1419 - Pages: 6
...The Case of the Ford Pinto By James Abstract Product harm crisis can be defined as a sudden break in a product’s life cycle (Siomkos, G.J and Kurzbard. J. 1994). In 1971 the Ford Motor Company created a product harm crisis with the introduction of the Ford Pinto. The Ford Pinto is known to be one of the most dangerous vehicles ever produced in automotive history due to several serious design flaws. This paper will identify the factors that contributed to the product harm crisis, compare and contrast the findings of various studies on a product harm crisis and finally synthesis the research findings and provide a post mortem recommendation to the Ford Motor Company on how the Ford Pinto product crisis should have been handled. The Case of the Ford Pinto In 1968 the Ford Motor Company decided to market a vehicle that was small, inexpensive and would appeal to all car buyers. The Vice President of Ford Motor Company at the time was Lee Iacocca. Mr. Iacocca approved the plan for the Ford Pinto based on the parameters of the car weighing 2000 pounds and costing $2,000.00 dollars (Danley J. 2005). By placing these parameters on the car’s designers, they were limited from the beginning and ended up with a failed product. The key factors that contributed to the product crisis included the Ford Pinto being rushed to production in twenty five months, the timeframe to production causing designers and producers of the car to cut corners and finally...
Words: 979 - Pages: 4
...Case Study Discussion and Executive Summary June 27, 2011 MGT/216 Case Study Discussion and Executive Summary This paper explores “The Ford Pinto Case” managing of business ethics. Numerous factors suggest within this research that Ford Motor Company was negligent and violated its code of ethics. To understand how relationships are affected a closer look at Ford Motor Company missions and values will align Team B’s personal values with Ford Motor Company. In this paper the study to examine are the role of people, products, and profits in the decisions made regarding the Ford Pinto. Key factors surrounding the Ford Pinto Case The death of Lynn Marie Ulrich, Dana Ulrich and Lynn’s sister, and Judy Ann along with many others was what brought the controversy of the Ford Pinto’s faulty gas tank placement to a climax. After so many unnecessary deaths the release of the Ford Pinto was the responsibility of Ford’s CEO Henry Ford II and Ford’s new president Lee Iacocca. Iacocca reduced the average production of a car from three and a half years to a little over two years. Iacocca was aware that during crash testing the Pinto’s gas tank exploded upon collision but was desperate to expedite the vehicle’s release on his deadline. After the discovery of the Pinto’s faulty gas tank, Ford’s president decided it would be costly to make changes in the Pinto’s gas tank location and its size. The Ford Pinto cost $2000 and making changes would increase its price thus possibly...
Words: 1203 - Pages: 5
...In 1968, the Ford Motor Company, based upon a recommendation by then vice president Lee Iacocca, decided to launch a subcompact car which is Ford Pinto. In order to gain a large market share, the Ford Motor Company plans for the project was the 2000/2000 rule. The car’s designer was designed and developed Pinto could weigh no more than 2000 pounds and it could cost no more than 2000 dollar. The Product Planning Committee instituted this rule because of the extreme competition between all of the automotive companies at the time (Daniel Boyce, n.d). Due to the Ford Motor Company was implemented the 2000/2000 rule, the car’s designers had to cut corners and restricted their ability to design a car the way it should be designed. Therefore, the Ford Pinto is known to be one of the most dangerous cars produced in automotive history due to several serious design flaws. Daniel Boyce wrote an article titled “Ford Pinto Case Information”. In his article, he claimed that “Pinto’s problems originated with the placement of the gas tank. At that time of automobile production, it was customary to place the gas tank between the rear axle and the bumper, which would give the vehicle more trunk space. The only other place the gas tank would be mounted was above the rear axle, but that eliminated trunk space, and the developers of the Pinto wanted the most practical car they could produce. The gas tank was nine inches away from the rear axle. This might not seem like a big deal, but there were...
Words: 843 - Pages: 4
...THE FORD PINTO CASE The scandal and the trial On August 10, 1978, a tragic automobile accident occurred on U.S. Highway 33 near Goshen, Indiana. Sisters Judy and Lynn Ulrich (ages 18 and 16, respectively) and their cousin Donna Ulrich (age 18) were struck from the rear in their 1973 Ford Pinto by a van. The gas tank of the Pinto ruprured, the car burst into flames and the three teenagers were burned to death. Subsequently an Elkhart County grand jury returned a criminal homicide charge against Ford, the first ever against an American corporation. During the following 20-week trial, Judge Harold R. Staffeld advised the jury that Ford should be convicted of reckless homicide if it were shown that the company had engaged in “plain, conscious and unjustifiable disregard of harm that might result (from its actions) and the disregard involves a substantial deviation from acceptable standards of conduct”. The key phrase around which the trial hinged, of course, is “acceptable standards”. Did Ford knowingly and recklessly choose profit over safety in the design and placement of the Pinto's gas tank? Elkhart County prosecutor Michael A. Cosentino and chief Ford attorney James F. Neal battled dramatically over this issue in a rural Indiana courthouse. Meanwhile, American business anxiously awaited the verdict which could send warning ripples through board rooms across the nation concerning corporate responsibility and product liability. The Pinto controversy In 1977 the...
Words: 2378 - Pages: 10
...THE PINTO CASE A SHORT SUMMARY In the early 1960s Ford’s market position was being heavily eroded by competition from domestic and foreign manufactures of subcompacts. Lee Iacocca, then President of Ford, was determined to regain Ford’s share of the market by having a new subcompact, the Pinto, in production by 1970. Then Ford engineers crash tested an early model of the Pinto. They found that when the automobile was struck from the rear at 20 miles per hour, the gas tank regularly ruptured. Stray sparks could then ignite the spraying gasoline, engulf the car in flames and possibly burn the trapped occupants. Nonetheless, Ford management decided for several reasons to go ahead with production of the Pinto as designed. First, the design met all applicable federal laws and standards then in effect. Secondly, the Pinto was comparable in safety to other cars being produced by the auto industry. Third, an internal Ford study indicated that the social costs of improving the design outweighed the social benefits. According to the study it was estimated that a maximum of 180 deaths might result if the Pinto design were not changed. For purposes of cost/benefit analysis the Federal government at that time put a value of $200,000 on a human life. Consequently, the study reasoned, saving 180 lives was worth about a total of $36 million to society. On the other hand, improving the 11 million Pintos then being planned would cost about $11 per car for a total investment of $121...
Words: 727 - Pages: 3
...Pagaduan MBA-1 Business Ethics Case Study: The Ford Pinto 1. What moral issues does the Pinto case raise? Answer: The Pinto case raise moral issues in human rights because even there were various ways of making the Pinto’s tank safer they refused technical improvement to prevent gas tanks from leaking. Given that number of people killed by fires from car, how they can value those individuals’ lives? Ford officials decide not to push the modification of the cars because it will be costly for them and not considering human’s life. 2. Supposed Ford officials were asked to justify their decision. What moral principles do you think they would invoke? Assess Ford’s handling of the Pinto from the perspective of each of the moral theories discussed in this chapter. Answer: With the use of risk/benefit analysis required by NHTSA, Ford officials justified in its decision not to change the Pinto model to increase vehicle safety, not considering the balance outlook on company’s perspective and human safeness. The moral principles that should invoke Ford officials is the act utilitarianism because this approach evaluates each action separately and the consequences that arise including any harms and benefits incurred by any people involved in the case. 3. Utilitarians would say that jeopardizing motorists does not by itself make Ford’s action morally objectionable. The only morally relevant matter is whether Ford gave equal consideration to the interests...
Words: 527 - Pages: 3
...Ford Pinto: A Study of Ethics In the 1960s Ford Motor Company, under pressure from stakeholders and the pressures involved in competing with the foreign vehicle market set out to manufacture a vehicle that was smaller, lighter and less expensive than the competition’s product. This vehicle was designed and moved into production within 2 years, much quicker than the 3 ½ year company norm and is still the shortest vehicle production planning schedule in history. The result: The Ford Pinto. While the Pinto was in the design phase it was decided that the fuel tank would be placed under the rear fender instead of over the rear axel to allow for more trunk room in the car. This design however, was quite flawed. The Pinto being smaller than the other American made cars was not built using the same frame design; a design that was manufactured to prevent the fuel tank from exploding upon a rear impact collision. Upon testing a serious defect was found with the placement of the fuel tank. It was determined that if the Pinto was involved in a rear end collision the fuel tank may rupture and burst into flames causing serious injury or death to the passengers. Team A will be examining the ethical dilemmas involved in the case and the solutions that we would recommend today and the solutions that would have been ethically appropriate in 1971. Lee Iacocca was the president of Ford Motor Company in 1971 and was the directive authority behind the creation of the Ford Pinto. He wanted a...
Words: 1776 - Pages: 8
...Responsible Commerce (COMM 101) Case 2.3 (The Ford Pinto) Week 4 1. What moral issues does the Pinto case raise? Moral issues that Ford Pinto case raises included producing dangerous products which are not safe to use it without informing the dangerous of the products to the public. In addition, lobbying the NHTSA to delay the safety measure of the products is also one of the moral issues that Ford Pinto case raises. (53 words) 2. Suppose Ford officials were asked to justify their decision. What moral principles do you think they would invoke? Assess Ford’s handling of the Pinto from the perspective of each of the moral theories discussed in this chapter. The theory of egoism is most suitable to describe the Ford Pinto case. Ford is doing things that benefit the organization itself. In addition, Ford only considered the short term benefits and neglected the long term interests of the organization itself. The handling of the Pinto from the perspective of each of the moral theories is as following. Act utilitarianism says that Ford did not produce the greatest possible balance of cost-benefit calculation for everyone affected. According to the Kant’s categorical imperatives, Ford should not place a monetary value on a human life. Based on W.D.Ross’s 7 basic Prima Facie Duties, Ford failed to apply the duties of nonmalefience because they did not produce safe cars. Lastly, Ford is unethical when applying the ethic of caring. Ford not only produced dangerous...
Words: 953 - Pages: 4
...for Pinto Case In the automobile industry, the Pinto case is a reminder of how business decisions can cause people to act unethical when money and social pressures arise. The Ford Motor Company (Ford) sought to compete with foreign car manufacturers and expedite the production of vehicles even if it meant disregarding red flag signals. Your gut can still be useful in alerting you that something might be wrong—that you’re facing an ethical dilemma—in the first place (Trevino & Nelson, 2007). The Pinto case questions the behavior of employees who acted unethical even when presented with safety issues that would change the lives of consumers. The following summary will provide details about the Pinto case. Key factors surrounding the Ford Pinto case A key factor surrounding the Ford Pinto case was cost and safety. Ford was aware that the Pinto exploded when rear-ended. Dennis Gioia brought his concern to the committee. Because of the lack of evidence, the committee voted not to recall. Even after evidence was found, the committee again decided not to recall because in the word of Lee Iacocca “safety didn’t sell.” Ford became the topic of corporate social responsibility, unethical behavior and decision-making. At a time when fuel prices were on the rise, Ford decided to compete with foreign manufacturers by producing fuel efficient compact cars. The firm pushed to produce vehicles by breaking its ethical code and manufacturing cars that carried a safety hazard. Ford also...
Words: 1656 - Pages: 7
...Ford Pinto Case Study MGT/216 November 11, 2010 Executive Summary In the1960's, the American small-car industry had strong competition for Ford, Volkswagen and several Japanese companies. In order to battle their challengers, Ford expedited its most contemporary automobile, the Pinto, into manufacturing. Fabrication was completed in a smaller extent of time than is generally mandatory to generate an automobile. The expected time to produce a vehicle is forty-three months however Ford took no more than twenty- five months (Trevino & Nelson, 2007). While Ford had the opportunity to produce a new model that would decline the risk of the Ford Pinto from blowing up, the corporation selected not to execute the plan. This design expense would have a rate of $11 for each vehicle. A study demonstrated the innovative plan would have resulted in a reduced amount of 180 casualties. The corporation argued that they had utilized the traditional risk-benefit tests to decide if the financial expense of adjusting the modifications were larger than society’s shared benefit (Safety X Change, 2009). Ford relied on the figures; the cost would have been $137 million vs. the $49.5 million; a printed fee placed on the vehicle for damages, casualties and injuries. Three adolescent girls passed away in a 1973 Ford Pinto on August 10, 1978, after being impacted from the back by a driver in a small truck (University of Phoenix, 2007). The Ford Pinto was totally immersed in fire and the undesirable...
Words: 989 - Pages: 4