Basic Operation Playing your AV components ....... 36 Listening to the Radio .................. 38
Enjoying the Listening Modes ..... 48
Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.
Advanced Operation ..................... 54
Troubleshooting ............................ 62
En
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
WARNING
RISK OF ELECTRIC SHOCK DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Important Safety Instructions
1. 2. 3. 4. 5. 6. 7. 8. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, PORTABLE CART WARNING tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. S3125A Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen into the apparatus, C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation, E. If the apparatus has been dropped or damaged in any way, and F. When the apparatus exhibits a distinct change in performance this indicates a need for service. 16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit. 17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries. 18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.
9.
10.
11. 12.
13. 14.
2
Precautions
1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering. 4. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230–240 V, 50 Hz or AC 120 V, 60 Hz). Some models have a voltage selector switch for compatibility with power systems around the world. Before you plug in such a model, make sure that the voltage selector is set to the correct voltage for your area. Before you plug in this model, make sure that the voltage selector is set to the correct voltage for your area. If it isn’t, use a small screwdriver to set it as appropriate. For example, if the voltage in your area is 120 volts, set the selector to “120V.” If it’s between 220 and 240 volts, set it to “220-240V.”
ANTENNA
AM FM 75
• This unit’s top and rear panels may get warm after prolonged use. This is normal. • If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
CENTER SPEAKER
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
L
Y VIDEO 2 PB VIDEO 1 DVD
V
2
PR
S
VOLTAGE SELECTOR
R
IN
OUT OUT
MONITOR OUT
R
VOLTAGE SELECTOR
AC OUTLET
SWITCHED 100W MAX.
IN IN
IN
FRONT SPEAKERS B PRE OUT
120V
3
IN
OUT
IN
IN
FRONT
SURROUND
CENTER
SURR BACK
L L
REMOTE CONTROL
L
L
120V
SUB WOOFER
SUB WOOFER
220-240V
AV RECEIVER
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
R
R
R
R
CD
TAPE
VIDEO 2
VIDEO 1
DVD
220-240V
Pressing the [STANDBY/ON] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet. 5. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer. 6. Handling Notes • If you need to transport this unit, use the original packaging to pack it how it was when you originally bought it. • Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles dont la fiche est polarisée: ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
3
Precautions—Continued For British models
Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.
Supplied Accessories
Make sure you have the following accessories:
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
Remote controller and two batteries (AA/R6)
Indoor FM antenna
AM loop antenna
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse. If the power cord’s plug is not suitable for your socket outlets, cut it off and fit a suitable plug. Fit a suitable fuse in the plug.
Power-plug adapter Only supplied in certain countries. Use this adapter if your AC outlet does not match with the plug on the AV receiver’s power cord. (Adapter varies from country to country.)
Surround Back Left Surround Back Left Zone 2 Left Zone 2 Left Surround Back Left Surround Back Left Zone 2 Left Zone 2 Left Surround Back Right Surround Back Right Zone 2 Right Zone 2 Right Surround Back Right Surround Back Right Zone 2 Right Zone 2 Right Front Left Front Left SP-B / Zone 2 Left SP-B / Zone 2 Left Front Right Front Right SP-B / Zone 2 Right SP-B / Zone 2 Right Surround Left Surround Left Surround Right Surround Right Center Center Center Center
For European Models
Front Left Front Left SP-B / Zone 2 Left SP-B / Zone 2 Left Front Right Front Right SP-B / Zone 2 Right SP-B / Zone 2 Right Surround Left Surround Left
1
We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3. GROEBENZELL, GERMANY
K. MIYAGI
2 3
Speaker Cable
Speaker cable labels * In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operation are the same regardless of color.
Processing
• Dolby*1 Digital EX and Dolby Pro Logic IIx • DTS, DTS-ES Matrix/Discrete, DTS Neo:6, and DTS 96/24*2 • Neural Surround*3 (North American models only) • CinemaFILTER function • Linear PCM 192 kHz/24-bit D/A converters on all channels • Pure Audio listening mode (not North American model) • Powerful and highly accurate 32-bit DSP processing
Audio/Video
• Adjustable crossover (40, 50, 60, 80, 100, 120, 150, 200 Hz) • HDTV-capable component video (3 inputs, 1 output) • 3 S-Video inputs, 2 outputs • 4 assignable digital inputs (3 optical, 1 coaxial) • Subwoofer pre out • Color-coded 7.1 multichannel input for use with Super Audio CD and DVD-Audio • A/B speaker drive • Color-coded speaker terminal posts
Tuner
• XM*4 Satellite Radio (North American models only)
*XM Passport System required; sold separately.
• 40 AM/FM/XM presets • AM/FM auto tuning • RDS (Radio Data System) (Europe only)
Remote Controller
• Preprogrammed for use with other AV components
5
Enjoying Home Theater
Speaker Sets A and B
You can use two sets of speakers with the AV receiver: speaker set A and speaker set B. Speaker set A should be used in your main listening room for up to 7.1-channel playback.
*While speaker set B is on, speaker set A is reduced to 5.1-channel playback.
Speaker set B can be used in another room and offers 2-channel stereo playback.
*Only analog input sources are output by speaker set B. Speaker set A
AV receiver
SPEAKERS A B
Speaker set B On Off
Indicator
Output Set A: 5.1 channels Set B: 2 channels Set A: 7.1 channels Set B: 2 channels No sound
Remote controller
On or Off
A A
B B
On Off
Speaker Set A: Main Room
Front left and right speakers These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward. Surround back left and right speakers These speakers further enhance the Center speaker realism of surround sound and This speaker enhances the improve sound localization behind the front left and right speakers, listener. Position them behind the lismaking sound movements tener about 2–3 feet (60–100 cm) distinct and providing a full above ear level. sound image. For movies it’s used mainly for dialog. * While speaker set B is on, these Position it close to your TV speakers output no sound. facing forward at about ear level, or at the same height as the front left and right speakers. Corner
Subwoofer The subwoofer handles the bass sounds of the LFE (LowFrequency Effects) channel. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the way along the wall, as shown.
1/3 wall length
Speaker Set B: Sub Room
Surround left and right speakers These speakers are used for precise sound positioning and to add realistic ambience. Position them at the sides of the listener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally they should be equally spaced from the listener.
6
Contents
Introduction
Important Safety Instructions ....................2 Precautions .................................................3 Supplied Accessories.................................4 Features .......................................................5 Enjoying Home Theater ..............................6
Speaker Sets A and B ...................................6
Basic Operation
Playing Your AV Components ................ 36
Basic AV Receiver Operation ..................... 36 Using the Multichannel DVD Input.............. 37 Displaying Source Information.................... 37
Listening to the Radio.............................. 38
Listening to AM/FM stations ....................... 38 Presetting AM/FM Stations and XM Channels..................................... 39 Listening to XM Satellite Radio® (North American Models Only) ................. 42
Getting to Know the AV Receiver ..............8 Remote Controller.....................................11
Common Functions.................................. 46
Connection
Connecting Your Speakers ......................16 Connecting Antennas ...............................18 Connecting Your Components ................20
About AV Connections ................................20 Connecting Audio and Video Signals to the AV Receiver ....................................21 Which Connections Should I Use?..............21 TV or Projector ..........................................22 DVD player .................................................23 VCR or DVD Recorder for Playback ...........25 VCR or DVD Recorder for Recording..........26 Camcorder, Games Console, or Other Device.........................................26 Satellite, Cable, Set-top box, or Other Video Source ..............................27 CD Player or Turntable................................28 HDD-compatible Component ......................29 Cassette, CDR, MiniDisc, or DAT Recorder.......................................30 Connecting the Power Cord of Another Component ...............................................30 Connecting Onkyo Components..........31 Connecting the Power Cord ........................31
Setting the Display Brightness.................... 46 Adjusting the Bass and Treble.................... 46 Muting the AV Receiver .............................. 46 Using the Sleep Timer ................................ 47 Using Headphones ..................................... 47 Adjusting Speaker Levels ........................... 47
Enjoying the Listening Modes
Using the Listening Modes...................... 48
Selecting Listening Modes.......................... 48 About the Listening Modes ......................... 50 Using the Late Night Function .................... 52 Using the CinemaFILTER........................... 52 Using the Audio Adjust Settings ................. 52
Advanced Operation
Recording.................................................. 54 Advanced Setup ....................................... 55
Advanced Speaker Settings ....................... 55 Digital Input Signal Formats ....................... 57 Correcting Sound and Picture Sync ........... 58
Controlling Other Components............... 59
Entering Remote Control Codes................. 59 Remote Control Codes for Onkyo Components Connected via .............. 60 Resetting REMOTE MODE Buttons ........... 60 Resetting the Remote Controller ................ 60
Turning On & First Time Setup
Turning On the AV Receiver ....................32 First Time Setup ........................................33
Assigning Digital Inputs to Input Sources ....33 Changing the Input Display .........................33 Minimum Speaker Impedance Setup (not North American model)......................34 Speaker Configuration.................................34
Troubleshooting ....................................... 62
If you can’t resolve an issue, try resetting the AV receiver by holding down the [VIDEO 1] button and pressing the [STANDBY/ON] button.
Getting to Know the AV Receiver
Front Panel
North American Model
1 2
3
4
5
6
TUNING PRESET
7
MASTER VOLUME
STANDBY/ON
STANDBY
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
8
Other Models
9
J
K L
M N OP Q R S
T
MASTER VOLUME
TUNING PRESET
STANDBY/ON
STANDBY
ENTER
PURE AUDIO
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
U
For detailed information, see the pages in parentheses.
O (European model only)
F Arrow/TUNING/PRESET and ENTER buttons
When AM, FM, or XM is selected, the TUNING [ ] [ ] buttons are used for radio tuning, and the PRESET [ ] [ ] buttons are used to select radio presets (see page 39). With the setup menus, they work as arrow buttons and are used to select and set items. The ENTER button is also used with the setup menus.
A STANDBY/ON button (32)
Sets the AV receiver to On or Standby.
B STANDBY indicator (32)
Lights up when the AV receiver is on Standby and flashes while a signal is being received from the remote controller.
C Remote-control sensor (11)
Receives control signals from the remote controller.
G MASTER VOLUME control (36)
Sets the volume of the AV receiver to MIN, 1 through 79, or MAX.
D Display
See “Display” on page 9.
E Input selector buttons (36)
Select the input sources. The [MULTI CH] button selects the multichannel DVD input.
H PHONES jack (47)
This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.
I SPEAKERS A and B buttons (6, 36)
Turn speaker sets A and B on or off.
8
Getting to Know the AV Receiver—Continued
J TONE, [–], and [+] buttons (46)
Used to adjust the bass and treble.
P MEMORY button (39)
Used when storing or deleting radio presets.
K STEREO button (48)
Selects the Stereo listening mode.
Q TUNING MODE button (38)
Selects the Auto or Manual tuning mode for AM and FM radio.
L LISTENING MODE [ ]/[ ] buttons (48)
Select the listening modes.
R RETURN button
Selects the previously displayed setup menu.
M DISPLAY button (37)
Displays various information about the currently selected input source.
S SETUP button
Used to access the setup menus.
N DIGITAL INPUT button (33, 57)
Used to assign the digital inputs and to specify the format of digital input signals.
T VIDEO 3 INPUT (26, 54)
Used to connect a camcorder, games console, and so on. There are jacks for composite video and analog audio.
O DIMMER or RT/PTY/TP button (41, 46)
Adjusts the display brightness. On the European model, this is the RT/PTY/TP button, and it’s used with RDS (Radio Data System). See “Using RDS (European Models Only)” on page 40.
U PURE AUDIO button and indicator (48)
The North American model doesn’t have this button and indicator. Selects the Pure Audio listening mode. The indicator lights up when this mode is selected.
Display
1
2
3
4
5
For detailed information, see the pages in parentheses.
6
XM (North American models only) (42): Lights up when XM radio is selected. MEMORY (39): Lights up when presetting radio stations. FM STEREO (38): Lights up when tuned to a stereo FM station.
1 A and B speaker indicators (6, 36)
Indicator A lights up when speaker set A is on. Indicator B lights up when speaker set B is on.
2 MUTING indicator (46)
Flashes while the AV receiver is muted.
3 Listening mode and format indicators (50)
Show the selected listening mode and the format of digital audio signals.
5 SLEEP indicator (47)
Lights up when the Sleep function has been set.
4 Radio indicators
TUNED (38): Lights up when tuned to a radio station. AUTO (38): For AM and FM radio, lights up when Auto Tuning is selected, and disappears when Manual Tuning mode is selected. RDS (European models only) (40): Lights up when tuned to a radio station that supports RDS (Radio Data System).
6 Message area
Displays various information about the selected input source.
9
Getting to Know the AV Receiver—Continued
Rear Panel B (North American model only) 3 4 5 6
XM
AM
8 (Only some models) 7
SURROUND BACK SPEAKERS SURROUND SPEAKERS FRONT SPEAKERS A CENTER SPEAKER
1
ANTENNA
FM 75
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
L
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
V
R
R
VOLTAGE SELECTOR
AC OUTLET
60Hz AC 120V SWITCHED TOTAL 120W 1A MAX.
2
PR
S
FRONT SPEAKERS B PRE OUT
SURROUND CENTER SURR BACK
120V
IN
OUT OUT
IN IN
IN
FRONT
3
IN
OUT
IN
IN
L L
REMOTE CONTROL
L
L
SUB WOOFER
220-240V
AV RECEIVER
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
9
J K
L
M
N
J CD IN
O
P
A DIGITAL IN OPTICAL 1, 2, 3, and COAXIAL
These optical and coaxial digital audio inputs are for connecting components with optical or coaxial digital audio outputs, such as CD and DVD players.
This analog audio input is for connecting a CD player’s analog audio output.
K TAPE IN/OUT
This analog audio input and output are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder, etc.
B XM antenna (on North American models)
This jack is for connecting an XM Passport System, sold separately (see page 42).
C COMPONENT VIDEO
A DVD player, TV, or other component that supports component video can be connected here.
L VIDEO 1 IN/OUT and VIDEO 2 IN
The VIDEO 1 inputs and outputs can be used to connect a VCR. The VIDEO 2 inputs can be used to connect another video source (e.g., cable/satellite receiver, set-top box, etc).
D AM ANTENNA
These push terminals are for connecting an AM antenna.
M DVD IN
These jacks can be used to connect a DVD player with an analog multichannel audio output for SACD and DVD-Audio playback.
E FM ANTENNA
This jack is for connecting an FM antenna.
F MONITOR OUT
The S-Video or composite video output should be connected to a video input on your TV or projector.
N SUBWOOFER PRE OUT
A powered subwoofer can be connected here.
G FRONT SPEAKERS A, SURROUND
SPEAKERS, CENTER SPEAKER, and SURROUND BACK SPEAKERS These terminal posts are for connecting speaker set A.
O FRONT SPEAKERS B
These push terminals are for connecting speaker set B.
P AC OUTLET
This switched AC outlet can be used to supply power to another AV component. The type of outlet depends on the country in which you purchased your AV receiver.
H VOLTAGE SELECTOR (Only some models)
This voltage selector provides compatibility with power systems around the world (see page 3).
I
REMOTE CONTROL This Remote Interactive jack can be connected to the jack on another -capable Onkyo component. To use , you must make an analog audio connection (RCA) between the AV receiver and the other component, even if they are connected digitally.
See pages 16–31 for hookup information.
10
Remote Controller
Installing the Batteries Aiming the Remote Controller
When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below.
Remote control sensor AV receiver STANDBY indicator
1
To open the battery compartment, press the small hollow and slide open the cover.
2
Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment.
Approx. 16 ft. (5 m)
3
Slide the cover shut.
Notes: • The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing. • If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably. • Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries. • The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing. • The remote controller will not work if there’s an obstacle between it and the AV receiver’s remote control sensor.
Notes: • If the remote controller doesn’t work reliably, try replacing the batteries. • Don’t mix new and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion. • Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.
11
Remote Controller—Continued
Using the Remote Controller
Including the AV receiver, the remote controller can be used to control up to seven different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the six REMOTE MODE buttons. ■ RECEIVER/TAPE Mode In RECEIVER/TAPE mode, you can control the AV receiver and an Onkyo cassette recorder connected via . ■ DVD and CD/MD/CDR/HDD Modes With these modes, you can control a DVD player and CD, MD, CDR, or HDD player or recorder. By entering the appropriate remote control code, you can control Onkyo components or components made by other manufacturers (see page 59). ■ TV, VCR and SAT/CABLE Modes With these modes, you can control a TV, VCR, and satellite or cable receiver. You must enter the appropriate remote control code first (see page 59).
RECEIVER/TAPE Mode
RECEIVER/TAPE mode is used to control the AV receiver. It can also be used to control an Onkyo cassette recorder connected via .
ON/STANDBY
RECEIVER
REMOTE MODE
RECEIVER
TAPE
1 2
1
V1
RECEIVER
TAPE
DVD
M D/CDR
TAPE
INPUT SELECTOR
2
V2
3
V3
CD
HDD
DVD
M D/CDR
3 1
D TUN
4 7
TAPE
5
MULTI CH
6
DVD
TV
K
8
TUNER
9
CD
VCR
12
CABLE
CD
HDD
10
11
+10
0
ENT DIMMER
CLR
SLEEP
SAT
4
TV
--/---
L
VOL
TV INPUT
VOL
DISC ALBUM
CH
M N
2 5
GUIDE TOP MENU
PREVIOUS MENU
VCR
CABLE
SP A / B
MUTING
SAT
36
PLAYLIST/CAT
ENTER PLAYLIST/CAT
7
O
RETURN SETUP
1
REMOTE MODE
Press one of the REMOTE MODE buttons to select a mode.
RECEIVER
TAPE
DVD
M D/CDR
4 8 9 J
LISTENING MODE STEREO SURROUND
CD
HDD
TV
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD CINE FLTR HDD LEVELLEVEL+
VCR
CABLE
SAT
P Q
2
Use the buttons supported by that mode to control the component. RECEIVER/TAPE mode: see right column DVD mode: see page 14 CD/MD/CDR/HDD mode: see page 15 TV, VCR, SAT/CABLE modes: see page 61
RC-647M
Buttons 1, 2, 3, and 4 are used when the TUNER or TAPE input is selected.
Note: Some of the remote controller operations described in this manual may not work as expected with other components.
12
Remote Controller—Continued
For detailed information, see the pages in parentheses. ■ Buttons used when the TUNER input is selected To select the Tuner (AM/FM/XM) as the input source, press:
RECEIVER
A ON/STANDBY button (32)
Sets the AV receiver to On or Standby.
B INPUT SELECTOR buttons (36)
Used to select the input sources.
8
TUNER
C MULTI CH button (37)
Selects the multichannel DVD input.
D DIMMER button (46)
Adjusts the display brightness.
1 Number, D TUN, and ENT buttons (39, 43)
Used to select AM and FM radio stations and XM radio channels directly.
E SP A/B button (6, 36)
Used to turn speaker sets A and B on or off.
2 CH +/– button (39)
Used to select radio presets.
F Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
Used to select and adjust settings.
3 Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
For AM and FM, the Up and Down [ tons are used for tuning. ]/[ ] but-
G RETURN button
Selects the previously displayed setup menu.
H LISTENING MODE buttons (48)
Used to select the listening modes. These buttons work in all remote controller modes. STEREO button Selects the Stereo listening mode. SURROUND button Selects the Dolby and DTS listening modes and the Neural Surround listening mode (North American model only). [ ]/[ ] buttons Used to select the available listening modes.
North American model only For XM, the Up and Down [ ]/[ ] buttons are used to select channels, and the [ENTER] button is used to change the search mode. The Left and Right [ ]/[ ] buttons are used to select categories. ■ Buttons used when the TAPE input is selected To select your Cassette deck as the input source, press:
RECEIVER
I TEST TONE, CH SEL, LEVEL-, and LEVEL+ buttons (35, 47, 57) Used to adjust the level of each speaker.
7
TAPE
J DISPLAY button (37)
Displays various information about the selected input source.
4 Playback buttons
On twin cassette decks, only deck B can be controlled. Play [ ] button Starts playback. Stop [ ] button Stops playback. Reverse Play [ ] button Starts reverse playback. Rewind and FF [ ]/[ ] buttons The Rewind [ ] button starts rewind. The FF [ ] button starts fast forward.
K REMOTE MODE buttons (12)
Used to select the remote controller modes. When a remote controller button is pressed, the REMOTE MODE button for the currently selected mode lights up.
L SLEEP button (47)
Used with the Sleep function.
M VOL [ ]/[ ] button (36)
Adjusts the volume of the AV receiver regardless of the currently selected remote controller mode.
N MUTING button (46)
Mutes or unmutes the AV receiver.
O SETUP button
Used to access the setup menus.
P CINE FLTR button (52)
Used with the CinemaFILTER function.
Q L NIGHT button (52)
Used with the Late Night function.
13
Remote Controller—Continued
DVD Mode
By default, the remote controller is set to control an Onkyo DVD player. To select your DVD player as the input source, press:
RECEIVER
A ON/STANDBY button
Sets the DVD player to On or Standby.
B Number buttons
Used to enter title, chapter, and track numbers and times for locating specific points.
C DISC +/– button
Selects discs on a DVD changer.
6
DVD
or
5
MULTI CH
D TOP MENU button
Selects a DVD’s top menu.
E Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
Used to navigate DVD menus and the DVD player’s onscreen setup menus.
F RETURN button
Exits the DVD player’s onscreen setup menus.
ON/STANDBY REMOTE MODE
G Playback buttons
DVD
1 2
1
V1
RECEIVER
TAPE
DVD
M D/CDR
INPUT SELECTOR
From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous, and Next.
2
V2
3
V3
CD
HDD
H SUBTITLE button
Selects subtitles.
4 7
TAPE
5
MULTI CH
6
DVD
TV
I AUDIO button
VCR
12
CABLE
8
TUNER
9
CD
10
11
+10
D TUN
Selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
K
VOL
J DISPLAY button
Displays information about the current disc, title, chapter, or track, including elapsed time, remaining time, total time, and so on.
TV INPUT
VOL
DISC ALBUM
CH
3 4
GUIDE TOP MENU
PREVIOUS MENU
K CLR button
L
SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT
Cancels functions and clears entered numbers.
L MENU button
Displays a DVD’s menu.
5 6
RETURN
M SETUP button
M
SETUP
Used to access the DVD player’s onscreen setup menus.
N RANDOM button
7
LISTENING MODE STEREO SURROUND
Used with the random playback function.
O REPEAT button
Used with the repeat playback functions.
LEVEL+
8 9 J
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD CINE FLTR HDD LEVEL-
N O P Q
P VCR, DVD, and HDD buttons
Used to select VCR, HDD (hard disk drive), or DVD playback on a VCR/DVD recorder with a built-in hard disk drive.
Q PLAY MODE button
Selects play modes on components with selectable play modes.
RC-647M
14
Remote Controller—Continued
CD/MD/CDR/HDD Mode
By default, the remote controller is set to control an Onkyo CD player. To select the input source, press:
9
CD
A ON/STANDBY button
Sets the component to On or Standby.
B Number buttons
Used to enter track numbers and times for locating specific points on CD/MD players.
C DISC/ALBUM +/– button
Selects discs on a CD changer, or the next or previous album on an HDD-compatible component.
CD player MD or CD recorder
2
V2
RECEIVER
7
TAPE
D Arrow [ ]/[ ] and ENTER buttons
Used to navigate menus on an HDD-compatible component.
7
TAPE
or
Next generation HDDcompatible component
E Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous and Next.
* If you’re using an MD, CDR, or HDD component, you must change the Input Display (see page 33).
F DISPLAY button
Displays information about the current disc or track on a CD player or MD/CD recorder, including elapsed time, remaining time, total time, and so on. On an HDD-compatible component, it turns on the back light for 30 seconds.
ON/STANDBY
REMOTE MODE
1 2
1
V1
RECEIVER
TAPE
DVD
M D/CDR
M D/CDR
INPUT SELECTOR
2
V2
3
V3
CD
HDD
CD
HDD
G CLR button
Cancels functions and clears entered numbers on a CD player or MD/CD recorder.
4 7
TAPE
5
MULTI CH
6
DVD
TV
8
TUNER
9
CD
VCR
12
CABLE
H MENU button
Used to navigate menus on an HDD-compatible component.
10
11
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
G
VOL
I PLAYLIST [ ]/[ ] buttons
Selects the previous or next playlist on an HDDcompatible component.
3
INPUT
TV
VOL
DISC ALBUM
CH
J RANDOM button
PREVIOUS MENU
4
GUIDE TOP MENU
8 9
Used with the random/shuffle playback function.
SP A / B
MUTING
K REPEAT button
Used with the repeat playback functions.
ENTER PLAYLIST/CAT PLAYLIST/CAT
L PLAY MODE button
Used to select play modes on components with selectable play modes.
RETURN
SETUP
E
LISTENING MODE STEREO SURROUND
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD CINE FLTR HDD LEVELLEVEL+
J K L
F
RC-647M
15
Connecting Your Speakers
Speaker Configuration
For the best surround-sound experience, you should connect seven speakers and a powered subwoofer. The following table shows which channels you should use based on the number of speakers that you have.
Number of speakers: Front left Front right Center Surround left Surround right Surround back* Surround back left Surround back right 2 ✓ ✓ 3 ✓ ✓ ✓ ✓ ✓ 4 ✓ ✓ 5 ✓ ✓ ✓ ✓ ✓ 6 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 7 ✓ ✓ ✓ ✓ ✓
Speaker Connection Precautions
Read the following before connecting your speakers: • North American models: You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated. • Other models: You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4 ohms” (see page 34). If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated. • Disconnect the power cord from the wall outlet before making any connections. • Read the instructions supplied with your speakers. • Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals to only positive (+) terminals, and negative (–) terminals to only negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural. • Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided. • Be careful not to short the positive and negative wires. Doing so may damage the AV receiver. • Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver. • Don’t connect a speaker to several terminals.
*If you’re using only one surround back speaker, connect it to the left (L) SURROUND BACK SPEAKERS terminals.
No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. Before using the AV receiver, you must specify which speakers are connected and their sizes (see page 34). To get the very best from your surround-sound system, you should also set the advanced speaker settings (see page 55.)
Attaching the Speaker Labels
The AV receiver’s positive (+) speaker terminals are color-coded for ease of identification. (The negative (–) speaker terminals are all black.)
Speaker terminal Front left Front right Center Surround left Surround right Surround back left Surround back right Color White Red Green Blue Gray Brown Tan
The supplied speaker labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. All you need to do then is to match the color of each label to the corresponding speaker terminal.
16
Connecting Your Speakers—Continued
Connecting Speaker Set A Connecting Speaker Set B
5/8" (15 mm)
1
Strip 5/8" (15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.
1
Strip 3/8" (10 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown. While pressing the lever, insert the wire into the hole, and then release the lever. Make sure that the terminals are gripping the bare wires, not the insulation.
3/8" (10 mm)
2
Unscrew the terminal. Fully insert the bare wire, making sure that it’s touching the threaded shaft in the center. Screw the terminal tight.
2
Connecting a Powered Subwoofer
Using a suitable cable, connect the AV receiver’s SUBWOOFER PRE OUT to the input on your powered subwoofer. If your subwoofer is unpowered and you’re using an external amplifier, connect the SUBWOOFER PRE OUT to it’s input. Note: Make sure the plugs are pushed in all the way.
Note: While speaker set B is on, speaker set A is reduced to 5.1-channel playback.
Speaker Set A Front right speaker Front left speaker
The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one surround back speaker, connect it to the left (L) SURROUND BACK SPEAKERS terminals.
Center speaker
XM
AM
ANTENNA
FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
CENTER SPEAKER
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
L
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
CENTER SPEAKER
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
L
R R AC OUTLET
AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX.
L
V
2
PR
S
FRONT SPEAKERS B PRE OUT
SURROUND CENTER SURR BACK
IN
OUT OUT
IN IN
IN
FRONT
3
IN
OUT
IN
IN
L L
REMOTE CONTROL
L
L
SUB WOOFER
AV RECEIVER
R
R
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
LINE INPUT
Front right speaker
Front left speaker
Powered subwoofer
Surround back right speaker
Surround back left speaker
Surround right speaker
Surround left speaker
Speaker Set B
17
Connecting Antennas
This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.
AM antenna push terminals FM antenna jack
XM
AM
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use only.
1
Assemble the AM loop antenna, inserting the tabs into the base, as shown.
ANTENNA
FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
CENTER SPEAKER
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
L
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
V
R
R
AC OUTLET
AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX.
2
PR
S
FRONT SPEAKERS B PRE OUT
SURROUND CENTER SURR BACK
IN
OUT OUT
IN IN
IN
FRONT
3
IN
OUT
IN
IN
L L
REMOTE CONTROL
L
L
SUB WOOFER
AV RECEIVER
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
2
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
1
Attach the FM antenna, as shown. ■ American Model
Connect both wires of the AM loop antenna to the AM push terminals, as shown. (The antenna’s wires are not polarity sensitive, so they can be connected either way around). Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.
Insert the plug fully into the jack.
Push
Insert wire
Release
■ Other Models
Insert the plug fully into the jack.
Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.
Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception. Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords. If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 19).
2
Use thumbtacks or something similar to fix the FM antenna into position.
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself when using thumbtacks. If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 19).
18
Connecting Antennas—Continued
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.
Outdoor antenna
FM 75
Insulated antenna cable AM loop antenna
Notes: • Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft. • For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter. • Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc. • For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment. • Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards. ■ Using a TV/FM Antenna Splitter It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.
Outdoor AM antennas work best when installed horizontally outside, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected. Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.
TV/FM antenna splitter To AV receiver To TV (or VCR)
19
Connecting Your Components
About AV Connections
• Before making any AV connections, read the manuals supplied with your other AV components. • Don’t connect the power cord until you’ve completed and double-checked all AV connections.
AV Connection Color Coding
RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.
Left (white) Right (red) (Yellow) Composite video Analog audio Left (white) Right (red) (Yellow) Right!
Optical Digital Jacks
The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way. Caution: To prevent shutter damage, hold the optical plug straight when inserting and removing.
• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions). • To prevent interference, keep audio and video cables away from power cords and speaker cables.
Wrong!
AV Cables and Jacks
Video
Cable
Y Y PB
PB Y
Jack
Description
Component video cable
PB PR
PR
PR
Component video separates the luminance (Y) and color difference signals (PR, PB), providing the best picture quality. (Some TV manufacturers label their component video jacks slightly differently.)
S
S-Video cable
S-Video separates the luminance and color signals and provides better picture quality than composite video. Composite video is commonly used on TVs, VCRs, and other video equipment. Use only dedicated composite video cables.
Composite video cable
V
Audio
Cable Optical digital audio cable Jack
OPTICAL
Description
This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for coaxial. This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for optical. This cable carries analog audio. It’s the most common connection format for analog audio and can be found on virtually all AV components. This cable carries multichannel analog audio and is typically used to connect DVD players with a 7.1channel analog audio output. Several standard analog audio cables can be used instead of a multichannel cable.
Coaxial digital audio cable
COA XIAL
Analog audio cable (RCA)
L
R
Multichannel analog audio cable (RCA)
Note: The AV receiver does not support SCART connections.
20
Connecting Your Components—Continued
Connecting Audio and Video Signals to the AV Receiver
By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver.
: Signal Flow Video Audio Video Audio TV, projector, etc.
Speakers (see page 17 for hookup details) DVD player, etc.
Which Connections Should I Use?
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide. For video components, such as a DVD player, you must make an audio connection and a video connection.
Video Connection Formats
When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats, so only outputs of the same format as the input will output the signal.
Video Signal Flow Chart DVD player, etc. Output IN AV Receiver OUT Input TV, projector, etc.
Composite S-Video Component Composite S-Video Component Composite S-Video Component
Audio Connection Formats
When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats. For example, audio signals connected to an OPTICAL or COAXIAL digital input are not output by the analog TAPE OUT, so if you want to record from, for example, your CD player, in addition to connecting it to a digital input, you must also connect it to the analog CD IN.
Audio Signal Flow Chart CD player, etc. Output IN AV Receiver OUT Input Cassette recorder, etc.
Analog Optical Coaxial Analog Multichannel Optical
Coaxial
Analog
Multichannel
21
Connecting Your Components—Continued
Connecting a TV or Projector
Step 1: Video Connection Choose a video connection that matches your TV ( A , B , or C ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches your TV ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from your TV and listen via speaker set B. • To enjoy Dolby Digital and DTS, use connection b or c . (For recording, use a and b , or a and c .)
Connection A B C a b c AV receiver COMPONENT VIDEO OUT MONITOR OUT S MONITOR OUT V VIDEO 2 IN L/R DIGITAL IN COAXIAL DIGITAL IN OPTICAL 2 Signal flow TV Component video input S-Video input Composite video input Analog audio L/R output Digital coaxial output Digital optical output Picture quality Best Better Standard
⇒ ⇒ ⇒ ⇐ ⇐ ⇐
XM
ANTENNA
AM FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
C S
b c
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
L
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
C
R R
V
2
PR
S
IN
OUT OUT
IN IN
IN
FRONT SURROUND CENTER SURR BACK
3
IN
OUT
IN
IN
B
FRONT SPEAKERS B PRE OUT
L L L L
SUB WOOFER
A
REMOTE CONTROL
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
a
L COAXIAL OUT OPTICAL OUT Y PB PR COMPONENT VIDEO IN AUDIO OUT
R S VIDEO IN VIDEO IN
Connect one or the other Connection b must be assigned (see page 33)
TV, projector, etc.
Hint!
If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see pages 25 and 27).
22
Connecting Your Components—Continued
Connecting a DVD player
Step 1: Video Connection Choose a video connection that matches your DVD player ( A , B , or C ), and then make the connection. You must connect the AV receiver to your TV via the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD player ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from a DVD and listen via speaker set B. • To enjoy Dolby Digital and DTS, use connection b or c . (For recording, use a and b , or a and c .) • If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left and right outputs for connection a .
Connection A B C a b c AV receiver COMPONENT VIDEO DVD IN DVD IN S DVD IN V DVD IN FRONT DIGITAL IN COAXIAL DIGITAL IN OPTICAL 1 Signal flow DVD player Component video output S-Video output Composite video output Analog audio L/R output Digital coaxial output Digital optical output Picture quality Best Better Standard
⇐ ⇐ ⇐ ⇐ ⇐ ⇐
XM
ANTENNA
AM FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
b
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
L
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
C
R R
V
c
2
PR
S
IN
OUT OUT
IN IN
IN
FRONT SURROUND CENTER SURR BACK
3
IN
OUT
IN
IN
B
FRONT SPEAKERS B PRE OUT
L L L L
SUB WOOFER
A
REMOTE CONTROL
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
a
L COAXIAL OUT OPTICAL OUT Y PB PR COMPONENT VIDEO OUT AUDIO OUT
R S VIDEO OUT VIDEO OUT
Connect one or the other Connection c must be assigned (see page 33)
DVD player
To connect a DVD player or DVD-Audio/SACD-capable player with a multichannel analog audio output, see page 24.
23
Connecting Your Components—Continued
Hooking Up the Multichannel DVD Input
If your DVD player supports multichannel audio formats such as DVD-Audio or SACD, and it has a multichannel analog audio output, you can connect it to the AV receiver’s multichannel DVD input. Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s DVD IN FRONT L/R, CENTER, SURROUND L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your DVD player. If your DVD player has a 5.1-channel analog audio output, don’t connect anything to the AV receiver’s SURR BACK L/R jacks.
XM
AM
ANTENNA
FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
CENTER SPEAKER
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
L
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
V
R
R
7.1 ch
CENTER SURR BACK L
2
PR
S
5.1 ch
IN
OUT OUT
IN IN
IN
FRONT SURROUND CENTER SURR BACK
FRONT SPEAKERS B PRE OUT FRONT
3
IN
OUT
IN
IN
SURROUND
L
L
REMOTE CONTROL
L
L
SUB WOOFER
L
R R R R
SUB WOOFER
R DVD SUB WOOFER
R
CD
TAPE
VIDEO 2
VIDEO 1
DVD
L FRONT
R
L SURROUND
R CENTER SUB WOOFER
L SURR BACK
R
DVD player
24
Connecting Your Components—Continued
Connecting a VCR or DVD Recorder for Playback
Hint! With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV receiver, useful if your TV has no audio outputs.
Step 1: Video Connection Choose a video connection that matches your VCR or DVD recorder ( A , B , or C ), and then make the connection. You must connect the AV receiver to your TV via the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your VCR or DVD recorder ( a , b , or c ), and then make the connection. • With connection a , you can listen to the VCR or DVD recorder even via speaker set B. • To enjoy Dolby Digital and DTS, use connection b or c . (To listen via speaker set B, use a and b , or a and c .)
Connection A B C a b c AV receiver COMPONENT VIDEO VIDEO 1 IN VIDEO 1 IN S VIDEO 1 IN V VIDEO 1 IN L/R DIGITAL IN COAXIAL DIGITAL IN OPTICAL 1 Signal flow VCR or DVD recorder Component video output S-Video output Composite video output Analog audio L/R output Digital coaxial output Digital optical output Picture quality Best Better Standard
⇐ ⇐ ⇐ ⇐ ⇐ ⇐
XM
ANTENNA
AM FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
b
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
C
R
V
c
2
PR
S
IN
OUT OUT
IN IN
IN
FRONT SURROUND
3
IN
OUT
IN
IN
CENTER
B
FRONT SPEAKER PRE OUT
SURR BACK
L L L L
SUB WOOFER
A
REMOTE CONTROL
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
a
L COAXIAL OUT OPTICAL OUT Y PB PR COMPONENT VIDEO OUT AUDIO OUT
R S VIDEO OUT VIDEO OUT
Connect one or the other Connection b must be assigned (see page 33) VCR, DVD recorder
25
Connecting Your Components—Continued
Connecting a VCR or DVD Recorder for Recording
Step 1: Choose a video connection that matches your VCR or DVD recorder ( A or B ), and then make the connection. The video source to be recorded must be connected to the AV receiver via the same type of connection. Step 2: Make the audio connection a .
DIGITAL IN COA XIAL OPTICAL 1 PB
XM
AM
VIDEO 2 IN VIDEO 1 IN
ANTENNA
FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
S
COMPONENT VIDEO
DVD IN
L
OUT
L
Y VIDEO 2 VIDEO 1 DVD
MONITOR OUT
B
V
R
R
2
PR
S
FRONT SPEAKERS B PRE OUT
CENTER SURR BACK
IN
OUT OUT
IN IN
IN
FRONT
3
a
REMOTE CONTROL
IN
OUT
IN
IN
SURROUND
A
L
SUB WOOFER
L
L
L
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
L R AUDIO IN S VIDEO IN
VCR, DVD recorder Connection A B a AV receiver VIDEO 1 OUT S VIDEO 1 OUT V VIDEO 1 OUT L/R Signal flow
VIDEO IN
VCR or DVD recorder S-Video input Composite video input Analog audio L/R input
Picture quality Better Standard —
⇒ ⇒ ⇒
Connecting a Camcorder, Games Console, or Other Device
Step 1: Make the video connection A . Step 2: Make the audio connection a .
MASTER VOLUME
TUNING PRESET
ENTER
a
VIDEO 3 INPUT
VIDEO L AUDIO R
TUNER
CD
RETURN
SETUP
VIDEO 3 INPUT L AUDIO R
DIGITAL INPUT
DIMMER
MEMORY
TUNING MODE
CLEAR
L AUDIO R OUT
A
VIDEO 3 INPUT VIDEO
VIDEO OUT
Camcorder, games console, etc.
Connection A a
AV receiver VIDEO 3 INPUT VIDEO 3 INPUT L/R
Signal flow
Camcorder or console Composite video output Analog audio L/R output
⇐ ⇐
26
Connecting Your Components—Continued
Connecting a Satellite, Cable, Set-top box, or Other Video Source
Hint! With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, useful if your TV has no audio outputs.
Step 1: Video Connection Choose a video connection that matches the video source ( A , B , or C ), and then make the connection. You must connect the AV receiver to your TV via the same type of connection. Step 2: Audio Connection Choose an audio connection that matches the video source ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from the video source and listen via speaker set B. • To enjoy Dolby Digital and DTS, use connection b or c . (For recording, use a and b , or a and c .)
Connection A B C a b c AV receiver COMPONENT VIDEO VIDEO 2 IN VIDEO 2 IN S VIDEO 2 IN V VIDEO 2 IN L/R DIGITAL IN COAXIAL DIGITAL IN OPTICAL 2 Signal flow Video source Component video output S-Video output Composite video output Analog audio L/R output Digital coaxial output Digital optical output Picture quality Best Better Standard
⇐ ⇐ ⇐ ⇐ ⇐ ⇐
XM
ANTENNA
AM FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
b
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
Y VIDEO 2 PB VIDEO 1
DVD
C
MONITOR OUT
V
R
2
PR
S
c A
IN
OUT OUT
IN IN
IN
3
IN
OUT
IN
IN
FRONT
B
FRON SPEAKE PRE OUT
CENTER SURR BACK
SURROUND
L L
REMOTE CONTROL
L
L
SUB WOOFER
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
a
L COAXIAL OUT OPTICAL OUT Y PB PR COMPONENT VIDEO OUT AUDIO OUT
R S VIDEO OUT VIDEO OUT
Connect one or the other Connection b must be assigned (see page 33)
Satellite, cable, set-top box, etc.
27
Connecting Your Components—Continued
Connecting a CD Player or Turntable
■ CD Player or Turntable (MM) with Built-in Phono Preamp Step 1: Choose a connection that matches your CD player ( a , b , or c ). Use connection a for a turntable with a built-in phono preamp.
b
Connect one or the other Connection b must be assigned (see page 33)
DIGITAL IN
DIGITAL IN COA XIAL OPTICAL 1
XM
AM
VIDEO 2 IN VIDEO 1 IN
ANTENNA
FM 75
SURROUND BACK SPEAKERS
COMPONENT VIDEO
DVD IN
L
OUT
IN
COAXIAL
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
L
V R
L R CD AUDIO OUTPUT
c
R
PR
OPTICAL 3 IN L R CD
2
S
IN
OUT OUT
IN IN
IN
FRONT SURROUND CENTER
3
IN
OUT
IN
IN
SURR BACK
L
REMOTE CONTROL
L
L
R
R
R
SUB WOOFER
a
VIDEO 2 VIDEO 1 DVD
CD
TAPE
a
R
COAXIAL OUT
L
OPTICAL OUT
AUDIO OUT
CD player
Turntable (MM) with built-in phono preamp
• With connection a , you can listen to and record audio from your CD player or turntable and listen via speaker set B. • To connect the CD player digitally, use connection b or c . (For recording, use a and b , or a and c .)
Connection a b c AV receiver CD IN L/R DIGITAL IN COAXIAL DIGITAL IN OPTICAL 3 Signal flow CD or turntable Analog audio L/R output Digital coaxial output Digital optical output
⇐ ⇐ ⇐
■ Turntable (MM) with no Phono Preamp Built-in A phono preamp is necessary to connect a turntable that doesn’t have a phono preamp built-in.
XM
AM
■ Turntable with an MC (Moving Coil) Cartridge An MC head amp and phono preamp are necessary to connect a turntable with an MC (Moving Coil) cartridge.
XM
ANTENNA
FM 75
ANTENNA
AM FM 75
SURROUND BACK SPEAKERS
SURROUND BACK SPEAKERS
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
DIGITAL IN COA XIAL
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
Y VIDEO 2 VIDEO 1 DVD MONITOR OUT
OPTICAL
V
R
1
PB
V
R
2
PR
S
2
PR
S
IN
OUT OUT
IN IN
IN
IN
OUT OUT
IN IN
IN
FRONT SURROUND CENTER SURR BACK
3
3
IN
OUT
IN
IN
FRONT
SURROUND
CENTER
SURR BACK
IN
OUT
IN
IN
L
REMOTE CONTROL
L
L
REMOTE CONTROL
L
L
L
R
R
R
SUB WOOFER
R
R
R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
CD
TAPE
VIDEO 2
VIDEO 1
DVD
IN L R CD
AUDIO OUTPUT L R
IN
AUDIO OUTPUT L R
AUDIO INPUT L R
AUDIO OUTPUT L R
Phono preamp
L R CD
Phono preamp MC head amp or MC transformer
AUDIO OUTPUT L R
AUDIO INPUT L R
AUDIO OUTPUT L R
AUDIO INPUT L R
28
Connecting Your Components—Continued
Connecting an HDD-compatible Component
As of this printing, the Onkyo Remote Interactive Dock is the only HDD-compatible component available. ■ For HDD-compatible components that support video Connect your HDD-compatible component’s analog audio output jacks and S-Video output jack to the AV receiver’s VIDEO 2 IN L/R jacks and VIDEO 2 IN S jack. ■ For HDD-compatible components that don’t support video Connect your HDD-compatible component’s analog audio output jacks to the AV receiver’s TAPE IN L/R jacks.
S VIDEO OUT L
AUDIO OUT L R
AUDIO OUT R
XM
AM
ANTENNA
FM 75
XM
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
OUT
DIGITAL IN Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT COA XIAL OPTICAL
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
OUT
Y
V
1
PB
2
PR
S
2
IN
OUT OUT
PR
IN IN
IN
FRONT SURROUND
3
IN
OUT
IN
IN
3
IN
OUT
IN
L
REMOTE CONTROL
L
L
REMOTE CONTROL
L
L
R
R
R
R
R
CD
TAPE
VIDEO 2
VIDEO 1
D
CD
TAPE
Notes: • Connect the Remote Interactive Dock with an cable (see page 31). • Set the Remote Interactive Dock’s RI MODE switch to HDD. • Set the AV receiver’s Input Display to HDD (see page 33). • Refer to the Remote Interactive Dock’s instruction manual.
29
Connecting Your Components—Continued
Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
Step 1: Choose a connection that matches the recorder ( a , b , or c ), and then make the connection.
XM
b
ANTENNA
AM FM 75
DIGITAL IN
DIGITAL IN COA XIAL
VIDEO 2 IN VIDEO 1 IN
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS
COMPONENT VIDEO
DVD IN
L
OUT
Y VIDEO 2 VIDEO 1 DVD MONITOR OUT
COAXIAL
OPTICAL 1 PB
V
R
c
Connect one or the other These connections must be assigned (see page 33)
2
PR
S
OPTICAL
3
IN
OUT
IN IN IN
OUT OUT
IN IN
IN
FRONT
3
REMOTE CONTROL
L
L
L
SURROUND IN CENTER SURR BACK OUT L
a
F SPE PRE OUT
L
SUB WOOFER
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
R
TAPE
COAXIAL OUT
L
L
OPTICAL OUT
R
R IN OUT REC PLAY
Cassette recorder, CDR, etc.
• With connection a , you can listen via speaker set B. • To connect the recorder digitally, use connections a and b , or a and c .
Connection a b c AV receiver TAPE IN L/R TAPE OUT L/R DIGITAL IN COAXIAL DIGITAL IN OPTICAL 3 Signal flow Cassette/CDR/MD/DAT recorder Analog audio L/R output Analog audio L/R input Digital coaxial output Digital optical output
⇐ ⇒ ⇐ ⇐
Connecting the Power Cord of Another Component
The AV receiver has an AC outlet on its rear panel for connecting the power cord of another AV component. The other component’s power switch can then be left in the ON position so that it turns on or off when the AV receiver is set to On or Standby. Caution: • Make sure that the capacity of the component that you connect to the AC OUTLET does not exceed the stated capacity (e.g., 100 W). Notes: • Onkyo components connected via should be connected directly to a wall outlet, not the AV receiver’s AC OUTLET. • The socket type and capacity depends on the country in which you purchased the AV receiver.
SURROUND SPEAKERS FRONT SPEAKERS A CENTER SPEAKER
L
R
AC OUTLET
60Hz AC 120V SWITCHED TOTAL 120W 1A MAX.
FRONT SPEAKERS B PRE OUT
L
SUB WOOFER
AV RECEIVER
R
AC OUTLET
AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX.
European and some Asian models
American model
30
Connecting Your Components—Continued
Connecting Onkyo Components
Step 1: Make sure that each Onkyo component is connected to the AV receiver with an analog audio cable (connection a in the hookup examples) (see pages 22 to 30). Step 2: Make the connection. Step 3: If you’re using an MD, CDR, or HDD component, change the input Display (see page 33). With (Remote Interactive), you can use the following special functions:
■ Auto Power On/Standby When you start playback on a component connected via , if the AV receiver is on Standby, it will automatically turn on and select that component as the input source. Similarly, when the AV receiver is set to Standby, all components connected via will also go on Standby. This function will not work on components connected to an AC OUTLET on the AV receiver. ■ Direct Change When playback is started on a component connected via , the AV receiver automatically selects that component as the input source. If your DVD player is connected to the AV receiver’s multichannel DVD input, you’ll need to press the [MULTI CH] button to hear all channels (see page 37), as the Direct Change function only selects the FRONT DVD IN jacks. ■ Remote Control You can use the AV receiver’s remote controller to control your other -capable Onkyo components, pointing the remote controller at the AV receiver’s remote control sensor instead of the component. You must enter the appropriate remote control code first (page 60). Notes: • Use only cables for connections. cables are supplied with Onkyo players (DVD, CD, etc.). • Some components have two jacks. You can connect either one to the AV receiver. The other jack is for connecting additional -capable components. • Connect only Onkyo components to jacks. Connecting other manufacturer’s components may cause a malfunction. • Some components may not support all functions. Refer to the manuals supplied with your other Onkyo components.
IN L R
XM
AM
ANTENNA
FM 75
SURROUND BACK SPEAKERS
DIGITAL IN COA XIAL OPTICAL
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
CD
Y VIDEO 2 VIDEO 1 DVD MONITOR OUT
REMOTE CONTROL
1
PB
V
R
2
PR
S
FRONT
IN
OUT OUT
IN IN
IN
FRONT SURROUND CENTER SURR BACK
3
IN
OUT
IN
IN
L
REMOTE CONTROL
L
L
L R DVD
R
R
R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
e.g., CD player
R L ANALOG AUDIO OUT
e.g., DVD player
R L ANALOG AUDIO OUT
Connecting the Power Cord
• Connect the AV receiver’s power cord to a suitable wall outlet. Notes: • Before connecting the power cord, connect all of your speakers and AV components. • Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.
31
Turning On the AV Receiver
STANDBY/ON STANDBY indicator
MASTER VOLUME
TUNING PRESET
ON/STANDBY
REMOTE MODE
ON/STANDBY RECEIVER
1
V1
RECEIVER
TAPE
DVD
M D/CDR
INPUT SELECTOR
2
V2
3
V3
CD
HDD
4 7
ENTER
5
MULTI CH
6
DVD
TV
STANDBY/ON
STANDBY
8
TUNER
9
CD
VCR
12
CABLE
TAPE
MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD
RETURN SETUP
10
11
+10
D TUN
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
CLEAR
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
VOL
PREVIOUS MENU
SP A / B
MUTING
Turning On and Standby
1
AV receiver
STANDBY/ON
Remote controller
RECEIVER
Press the [STANDBY/ON] button. Alternatively, press the remote controller’s [RECEIVER] button, followed by the [ON/STANDBY] button. The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
or
ON/STANDBY
To turn the AV receiver off, press the [STANDBY/ON] button, or press the remote controller’s [ON/STANDBY] button. The AV receiver will enter Standby mode. To prevent any loud surprises when you next turn on the AV receiver, always turn down the volume before you turn it off.
Smooth Operation in a Few Easy Steps
To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the very first time. These settings only need to be made once. ■ Have you connected a component to a digital audio input? If you have, see “Assigning Digital Inputs to Input Sources” on page 33. ■ Have you connected an Onkyo MD recorder, CD recorder, or next generation HDD-compatible component? If you have, see “Changing the Input Display” on page 33.
COAX
OPT1
OUT IN
TAPE
CD recorder, MD recorder, RI Dock, etc.
■ Have you connected any speakers with an impedance of between 4 and 6 ohms? If you have, see “Minimum Speaker Impedance Setup” on page 34. (Not North American models.) ■ Do the speaker configuration—this is essential! See “Speaker Configuration” on page 34.
4–6 ohm speakers
32
First Time Setup
Assigning Digital Inputs to Input Sources Changing the Input Display
If you connect an -capable Onkyo MiniDisc recorder, CD recorder or next generation HDD-compatible component to the TAPE IN/OUT or VIDEO 2 IN jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver.
R
1
STANDBY/ON
STANDBY
2, 3
MASTER VOLUME
TUNING PRESET ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO
1, 2
STANDBY/ON
STANDBY
1, 2
MASTER VOLUME
TUNING PRESET
CLEAR
To enjoy Dolby Digital and DTS, you must connect your DVD player to the AV receiver digitally (coaxial or optical). Here are the default assignments.
Input selector DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE CD Default assignment COAX OPT 1 OPT 2 ------OPT 3
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
1
TAPE
Press the [TAPE] or [VIDEO 2] input selector button so that “TAPE” or “VIDEO2” appears on the display.
or
VIDEO 2
With this function, you can change the digital inputs assign. If, for example, you connect your DVD player to the DIGITAL IN OPTICAL 1 input (OPT1), you’ll need to assign it to the DVD input source, as follows.
1
DVD VIDEO 1 VIDEO 2 VCR VIDEO 3 TAPE
Press the input selector button for the input source that you want to assign. (Digital inputs cannot be assigned to the TUNER input source.)
2
TAPE
or
VIDEO 2
CD
Press and hold down the [TAPE] or [VIDEO 2] input selector button (about 3 seconds) to change the setting. Repeat this step to select MD, CDR, or HDD. For the TAPE input selector, the setting changes in this order: TAPE → MD → CDR → HDD For the VIDEO 2 input selector, the setting changes in this order: VIDEO 2 ↔ HDD
2
DIGITAL INPUT
Press the [DIGITAL INPUT] button. The current assignment appears.
3
DIGITAL INPUT
Press the [DIGITAL INPUT] button repeatedly to select COAX, OPT1, OPT2, OPT3, or “– – – –” (analog).
Note: HDD can be selected for the TAPE input selector or VIDEO 2 input selector, but not both at the same time.
Note: Make sure that components connected digitally are configured to output digital audio. Refer to the relevant manuals.
→
33
First Time Setup—Continued
Speaker Configuration
ON/STANDBY REMOTE MODE
RECEIVER
TAPE
DVD
M D/CDR
1
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
HDD
4 7
TAPE
5
MULTI CH
6
DVD
TV
8
TUNER
9
CD
VCR
12
CABLE
10
11
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
VOL
PREVIOUS MENU
This section explains how to specify your speaker configuration. For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large (full band). For those with a smaller diameter, specify Small (default crossover 100 Hz). The crossover frequency can be Cone diameter changed on page 55.
SP A / B
MUTING
2–8
RETURN
ENTER PLAYLIST/CAT PLAYLIST/CAT
RETURN
SETUP
1, 9
1
RECEIVER
Press the [RECEIVER] button, followed by the [SETUP] button.
LISTENING MODE STEREO SURROUND
Minimum Speaker Impedance Setup (not North American model)
If the impedance of any of the connected speakers is 4 ohms or more but less than 6, set the minimum speaker impedance to “4 ohms.” Note: Before you change this setting, turn down the volume.
SETUP
2
Use the Up and Down [ ]/[ ] buttons to select “1. SP Config,” and then press [ENTER].
1 2 3
Press the [RECEIVER] button, followed by the [SETUP] button. Use the Up and Down [ ]/[ ] buttons to select “0. Hardware Setup,” and then press [ENTER]. Use the Left and Right [ ]/[ ] buttons to select the setting for “Impedance.” 4 ohms: Select if the impedance of any connected speaker is 4 ohms or more but less than 6. 6 ohms: Select if the impedances of all connected speakers are between 6 and 16 ohms. Press the [RETURN] button to go to step 2 of the “Speaker Configuration” (next column).
3
While the “Subwoofer” setting is selected, use the Left and Right [ ]/[ ] buttons to select Yes or No. Yes: Select if a subwoofer is connected. No: Select if no subwoofer is connected. Use the Down [ ] button to select “Front,” and then use the Left and Right [ ]/[ ] buttons to select Small or Large. Small: Select if the front speakers are small. Large: Select if the front speakers are large. Note: • If the Subwoofer setting in step 3 is set to No, this setting is fixed at Large and does not appear.
4
Note: • This procedure can also be performed on the AV receiver by using the [SETUP], [ENTER], and arrow buttons.
34
First Time Setup—Continued
5
Use the Down [ ] button to select “Center,” and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Small: Select if the center speaker is small. Large: Select if the center speaker is large. None: Select if no center speaker is connected. Note: • If the Front setting in step 4 is set to Small, the Large option cannot be selected.
8
Use the Down [ ] button to select “Surr Back Ch,” and use the Left and Right [ ]/[ ] buttons to select 2ch or 1ch. 2ch: Select if two (left and right) surround back speakers are connected. 1ch: Select if one surround back speaker is connected. Note: • If the Surround and Surr Back settings in steps 6 and 7 are set to None, this setting does not appear.
6
Use the Down [ ] button to select “Surround,” and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Small: Select if the surround speakers are small. Large: Select if the surround speakers are large. None: Select if no surround speakers are connected. Note: • If the Front setting in step 4 is set to Small, the Large option cannot be selected.
9
SETUP
Press the [SETUP] button. Setup closes.
Testing the Speakers To test that all of the speakers are working properly, press the remote controller’s [TEST TONE] button.
LISTENING MODE STEREO SURROUND
AUDIO SUBTITLE RANDOM REPEAT
TEST TONE
TEST TONE
CH SEL PLAY MODE
LEVEL-
LEVEL+
DISPLAY VCR
L NIGHT DVD
CINE FLTR HDD
7
Use the Down [ ] button to select “Surr Back,” and use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Small: Select if the surround back speakers are small. Large: Select if the surround back speakers are large. None: Select if no surround back speakers are connected. Notes: • If the Surround setting in step 6 is set to None, this setting does not appear. • If the Surround setting in step 6 is set to Small, the Large option cannot be selected.
RC-647M
The test tone will be output by each speaker in turn and the name of each speaker will appear on the display. To turn off the test tone, press the [TEST TONE] button again. • If the test tone is not produced by a speaker, or it’s produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see page 17). • If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker configuration incorrectly (see page 34). • Testing cannot be performed while speaker set B is on or a pair of headphones is connected.
35
Playing Your AV Components
Basic AV Receiver Operation
MULTI CH
1
TUNING PRESET
4
MASTER VOLUME
ON/STANDBY
REMOTE MODE
RECEIVER
DVD
M D/CDR
1
TAPE
1
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
HDD
STANDBY/ON
STANDBY
4
ENTER
5
MULTI CH
6
DVD
TV
7
MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD
RETURN SETUP
8
TUNER
9
CD
VCR
12
CABLE
TAPE
10
11
+10
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
0
ENT DIMMER
CLR
SLEEP
SAT
D TUN
--/---
CLEAR
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
VOL
4
2
DISPLAY
2
PREVIOUS MENU
SP A / B
MUTING
ENTER PLAYLIST/CAT PLAYLIST/CAT
1
AV receiver
DVD VIDEO 1 VIDEO 2 VCR VIDEO 3 TAPE TUNER
Remote controller
RECEIVER
Use the AV receiver’s input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] REMOTE MODE button, and then use the INPUT SELECTOR buttons.
1
V1
2
V2
3
V3
CD
6
DVD
On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1, VIDEO 2, and VIDEO 3 input sources respectively.
7
TAPE
8
TUNER
9
CD
2
AV receiver
SPEAKERS A B
Remote controller
To turn the speakers on or off, use the AV receiver’s SPEAKERS [A] and [B] buttons, or use the remote controller’s [SP A/B] button. Pressing the remote controller’s [SP A/B] button cycles through the following settings: Speaker Set A → Speaker Set A&B → Speaker Set B → Off. Note that while speaker set B is on, speaker set A is reduced to 5.1-channel Indicators playback. See page 6 for more information about speaker sets A and B.
3 4
AV receiver
MASTER VOLUME
Start playback on the source component. To watch a DVD or other video source, on your TV, select the video input that’s connected to the AV receiver’s MONITOR OUT jack.
Remote controller
VOL
To adjust the volume, use the MASTER VOLUME control, or the remote controller’s [VOL] button. The volume can be set to MIN, 1 through 79, or MAX. Since the AV receiver is designed for home theater enjoyment, it has a wide volume range for precise adjustment.
5
Select a suitable listening mode and enjoy! See “Using the Listening Modes” on page 48.
36
Playing Your AV Components—Continued
Displaying Source Information
ON/STANDBY REMOTE MODE
RECEIVER
TAPE
DVD
M D/CDR
RECEIVER
INPUT SELECTOR
You can display various information about the current input source as follows.
RECEIVER
1
V1
2
V2
3
V3
CD
HDD
MULTI CH
4 7
TAPE
5
MULTI CH
6
DVD
TV
8
TUNER
9
CD
VCR
12
CABLE
10
11
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
DISPLAY
TV INPUT
Press the [RECEIVER] REMOTE MODE button, and then press the [DISPLAY] button repeatedly to cycle through the available information.
VOL
DISC ALBUM
CH
VOL
The following information can typically be displayed:
LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVELLEVEL+
Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode
DISPLAY
DISPLAY VCR
L NIGHT DVD
CINE FLTR HDD
RC-647M
Using the Multichannel DVD Input
The multichannel DVD input is for connecting a component with a 7.1-channel analog audio output, such as a DVD-Audio or SACD-capable DVD player, or an MPEG decoder. See page 24 for hookup information.
RECEIVER
*1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Note: • The listening mode is displayed only when speaker set A is on. Interpreting Surround Channel Information
Press the [RECEIVER] REMOTE MODE button, followed by the [MULTI CH] button. The MULTI CH indicator appears on the display.
MULTI CH indicator
MULTI CH
A
B C
Audio from the multichannel DVD input will now be used for the DVD input source. Note: • While the multichannel DVD input is selected, the Speaker Configuration settings on page 34 are ignored, and signals from the multichannel input are fed to the speakers as they are.
A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there’s surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes).
37
Listening to the Radio
Listening to AM/FM stations
TUNER TUNING
MASTER VOLUME
TUNING PRESET
Tuning into AM/FM Radio Stations
■ Auto Tuning Mode
1
TUNING MODE
STANDBY/ON
STANDBY
Press the [TUNING MODE] button so that the AUTO indicator appears on the display.
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
2
TUNING PRESET
TUNING MODE
Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found.
With the built-in tuner, you can enjoy AM and FM radio stations.
1
TUNER
Use the [TUNER] input selector button to select AM or FM. In this example, FM has been selected.
■ Manual Tuning Mode
1
Band Frequency
TUNING MODE
Press the [TUNING MODE] button so that the AUTO indicator disappears from the display.
(Actual display depends on country.)
2
TUNING PRESET
■ AM Frequency Step Setup (not North America and Europe) You must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted.
Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time.
1
Press the [SETUP] button, use the Up and Down [ ]/[ ] buttons to select “0. Hardware Setup,” and then press [ENTER]. Use the Up and Down [ ]/[ ] buttons to select “AM Freq,” and then use the Left and Right [ ]/[ ] buttons to select: 10 kHz: Select if 10 kHz steps are used in your area. 9 kHz: Select if 9 kHz steps are used in your area. Press the [SETUP] button. Setup closes.
2
The American model changes FM frequency in 0.2 MHz steps, 10 kHz steps for AM. For other models it’s 0.05 MHz steps for FM and 9 kHz (or 10 kHz) steps for AM. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also appears.
TUNED AUTO
FM STEREO
3
Tuning into Weak FM Stereo Stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Note: • You can also use the remote controller’s Up and Down [ ]/[ ] buttons to tune the radio.
38
Listening to the Radio—Continued
■ Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency.
ON/STANDBY REMOTE MODE
2
MEMORY
Press the [MEMORY] button. The MEMORY indicator appears and the preset number flashes.
RECEIVER
TAPE
DVD
M D/CDR
RECEIVER
INPUT SELECTOR
Number buttons D TUN
1
V1
2
V2
3
V3
CD
HDD
4 7
TAPE
5
MULTI CH
6
DVD
TV
3
CH +/–
TUNING
PRESET
8
TUNER
9
CD
VCR
12
CABLE
10
11
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 40.
ENTER
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
VOL
PREVIOUS MENU
SP A / B
MUTING
ENTER PLAYLIST/CAT PLAYLIST/CAT
4
MEMORY
RETURN
SETUP
1
RECEIVER
Press the [RECEIVER] button, followed by the [D TUN] button.
Press the [MEMORY] button again to store the station or channel. The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations and XM channels.
D TUN
(Actual display depends on country.) The [RECEIVER] button flashes.
■ Selecting Presets
1
TUNING
PRESET
2
Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87.5 (FM), press 8, 7, 5. Note: While the [RECEIVER] button is flashing, the input source cannot be changed by using the remote controller.
ENTER
To select a preset, use the PRESET [ ]/[ ] buttons, or the remote controller’s CH [+/–] button.
Select the preset that you want to delete. See the previous section. While holding down the [MEMORY] button, press the [TUNING MODE] button. The preset is deleted and its number disappears from the display.
STANDBY/ON
STANDBY
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO
CLEAR
MEMORY
TUNING MODE
You can store a combination of up to 40 of your favorite AM/FM radio stations and XM channels as presets.
1
Tune into the AM/FM station or XM channel that you want to store as a preset. See page 42 to select XM channels.
39
Listening to the Radio—Continued
Using RDS (European Models Only)
RDS only works with European models and only in areas where RDS broadcasts are available. When tuned into an RDS station, the RDS indicator appears.
RDS indicator
RDS Program Types (PTY)
Type None News reports Current affairs Display NONE NEWS AFFAIRS Description No program type. Reports on current events and happenings. Topical reporting of current affairs, often with a wider range of topics than news reports. General information such as weather forecasts, consumer affairs, medical help, etc. Live sports action, sports news, and interviews. Radio plays and serials.
Information INFO
■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. Many FM stations use it these days. In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.). The AV receiver supports four types of RDS information:
PS (Program Service)
Sport Education Drama Culture
SPORT
EDUCATE Formal educational programs. DRAMA CULTURE Cultural programs (including religious affairs).
Science and SCIENCE Programs about the natural technology sciences and technology. Varied VARIED Talk programs not covered by the above categories (e.g., quizzes, panel games, and comedy). Popular commercial music, usually from past or present sales charts (e.g., Top 40). Popular music with an alternative appeal, often not appearing on sales charts. Easy listening music (as opposed to Pop, Rock, or Classical). Classical music for general rather than specialist appreciation.
When tuned to an RDS station that’s broadcasting PS information, the station’s name will be displayed. Pressing the [DISPLAY] button will display the frequency for 3 seconds.
RT (Radio Text)
Pop music
POP M
When tuned to an RDS station that’s broadcasting text information, the text will be shown on the display (see page 41).
PTY (Program Type)
Rock music ROCK M
This allows you to search for RDS radio stations by type (see page 41).
TP (Traffic Program)
Middle of the road music Light classics Serious classics
M.O.R.M
LIGHT M
This allows you to search for RDS radio stations that broadcast traffic information (see page 41). Notes: • In some cases, the text characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be displayed when unsupported characters are received. This is not a malfunction. • If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all.
CLASSICS Performances of major orchestral works, symphonies, chamber music, etc. (including the Grand Opera).
Other music OTHER M Music styles not covered by the above categories (e.g., Jazz, Rhythm and Blues, Folk, Country, and Reggae). Alarm ALARM When an RDS station is making an emergency broadcast, ALARM will flash on the display.
40
Listening to the Radio—Continued
Displaying Radio Text (RT)
MASTER VOLUME
TUNING PRESET
4
ENTER
ENTER
STANDBY/ON
STANDBY
PURE AUDIO
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE VIDEO L AUDIO R
To start the search, press [ENTER]. The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search. When a station you want to listen to is found, press [ENTER]. If no stations are found, the message “Not Found” appears.
CLEAR
1
When tuned to an RDS station that’s broadcasting text information, the text can be displayed.
5
ENTER
1
RT/PTY/TP
Press the [RT/PTY/TP] button once. The RT information scrolls across the display.
Listening to Traffic News (TP)
1
STANDBY/ON
STANDBY
3
MASTER VOLUME
TUNING PRESET ENTER
Notes: • The message “Waiting” may appear while the AV receiver waits for the RT information. • If the message “No Text Data” appears on the display, no RT information is available.
PURE AUDIO
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
2
You can search for stations that broadcast traffic news.
Finding Stations by Type (PTY)
1
STANDBY/ON
STANDBY
3–5
MASTER VOLUME
TUNING PRESET ENTER
1
TUNER
Use the [TUNER] input selector button to select FM.
PURE AUDIO
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE VIDEO L AUDIO R
2
RT/PTY/TP
CLEAR
2
You can search for radio stations by type.
1
TUNER
Use the [TUNER] input selector button to select FM.
Press the [RT/PTY/TP] button three times. If the current radio station is broadcasting TP (Traffic Program), “[TP]” will appear on the display, and traffic news will be heard as and when it’s broadcast. If “TP” without square brackets appears, this means that the station is not broadcasting TP. To locate a station that is broadcasting TP, press [ENTER]. The AV receiver searches until it finds a station that’s broadcasting TP. If no stations are found, the message “Not Found” appears.
3 2
RT/PTY/TP
Press the [RT/PTY/TP] button twice. The current program type appears on the display. Use the PRESET [ ]/[ ] buttons to select the type of program you want. See the table on page 40.
ENTER
ENTER
3
TUNING
PRESET
41
Listening to the Radio—Continued
Listening to XM Satellite Radio® (North American Models Only)
Important XM Radio Information To receive XM Radio on this receiver you need to purchase an optional XM Passport System and subscribe to XM’s paid programming. Please note that XM is currently only licensed to provide service to the contiguous 48 United States (not available in Alaska and Hawaii) and portions of Canada. XM Radio service is not currently available in Mexico or any other region outside the continental U.S. and portions of Canada. For updates on service availability please visit XM's website at http://www.xmradio.com or http://www.xmradio.ca Note: Hardware and required basic monthly subscription sold separately. Premium Channels available at additional monthly cost. Installation costs and other fees and taxes, including a one-time activation fee may apply. Subscription fee is consumer only. All fees and programming subject to change. About XM Radio: There is a world beyond AM and FM. It is XM Satellite Radio. XM offers more than 160 digital channels of audio entertainment, including 100% commercial-free music channels, in the top markets in the U.S. Channels with frequent explicit language are indicated with an XL. Channel blocking is available for XM radio receivers by calling 1-800-XMRADIO. About XM Canada: XM Canada offers the most commercial-free music – and engaging talk show programs. XM Canada creates original content that reflects our unique Canadian culture and broadcasts it throughout North America. Canadian Satellite Radio Inc. offers its satellite radio service and operates under the XM Canada™ brand. XM Canada has an exclusive Canadian licence from XM Satellite Radio Inc. For more information about XM Canada, visit www.xmradio.ca or call 1-877-GET-XMSR A warning against reverse engineering: It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE® voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this or any other software contained in an XM Radio is explicitly prohibited from attempting to copy, decompile, reverse engineer, or disassemble the object code, or in any other way convert the object code into humanreadable form. The software is licensed solely for use within this product.
Connecting the XM Passport System
The XM Passport System is sold separately. You can purchase the XM Passport System from the XM Web site at: http://www.xmradio.com (U.S.A.) http://www.xmradio.ca (Canada) Connect the Passport System to the XM antenna jack on the rear panel.
XM antenna jack
XM
AM
ANTENNA
FM 75
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
FRONT SPEAKERS A
CENTER SPEAKER
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
L
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
V
R
R
AC OUTLET
AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX.
2
PR
S
FRONT SPEAKERS B PRE OUT
SURROUND CENTER SURR BACK
IN
OUT OUT
IN IN
IN
FRONT
3
IN
OUT
IN
IN
L L
REMOTE CONTROL
L
L
SUB WOOFER
AV RECEIVER
R R R R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
Put the XM Passport System by a southerly facing window, with nothing obstructing its path to the sky.
TUNER
TUNING
MASTER VOLUME
TUNING PRESET
STANDBY/ON
STANDBY
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
Selecting XM Satellite Radio
1
TUNER
Press the [TUNER] input selector button repeatedly to select XM. If “CHECK ANTENNA” appears on the display, make sure the XM Passport System is connected properly.
42
Listening to the Radio—Continued
Signing Up for XM Satellite Radio
Before you can use XM Satellite Radio, you must first sign up for an account. You’ll need a major credit card and your XM Satellite Radio ID, which you can get from the AV receiver, as explained below, or from the Passport System package and itself. ■ Channel Search Mode
1
Press the [RECEIVER] button, followed by the [ENTER] button to select “Channel Search” mode.
1
TUNING PRESET
Use the TUNING Up and Down [ ]/[ ] buttons to select channel 0. Your XM Satellite Radio ID number is displayed. Write it below. ID
2
Use the Up and Down [ ]/[ ] buttons to select a channel.
Channel number
Channel name
2
To sign up, go to: http://activate.xmradio.com Or call: 1-800-967-2346 For XM Canada, go to: http://xmradio.ca Or call: 1-877-GET-XMSR
You can also use the Left and Right [ ]/[ ] buttons to select a category. ■ Category Search Mode
1
Notes: • Channel 0 cannot be selected in Category Search mode. You must select Channel Search mode (see page 43). • The following letters are not used in XM Satellite Radio IDs: I, O, S, F.
Press the [RECEIVER] button, followed by the [ENTER] button to select “Category Search” mode.
2
Selecting XM Radio Channels
There are three ways to select XM radio channels: • Channel Search mode: select any channel. • Category Search mode: select channels by category. • Direct tuning: enter channel number. Note: You can’t select Channel Search or Category Search mode, while the Tuning Arrow indicators are flashing, as tuning is in progress.
ON/STANDBY REMOTE MODE
Use the Left and Right [ ]/[ ] buttons to select a category, and use the Up and Down [ ]/[ ] buttons to select a channel in that category.
■ Direct Tuning You can select an XM radio channel directly by entering its number.
1
D TUN
Press the [RECEIVER] button, followed by the [D TUN] button. The [RECEIVER] button flashes.
RECEIVER
TAPE
DVD
M D/CDR
RECEIVER
INPUT SELECTOR
Number buttons
1
V1
2
V2
3
V3
CD
HDD
4 7
TAPE
5
MULTI CH
6
DVD
TV
2
1
V1
8
TUNER
9
CD
VCR
12
CABLE
D TUN
10
11
2
V2
3
V3
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
ENT
VOL
4 7
TAPE
5
MULTI CH
6
DVD
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
8
TUNER
9
CD
11
PREVIOUS MENU
12
Within 8 seconds, use the number buttons to enter the channel number. The channel is selected. For example, to select channel #20, press 0, 2, 0, or 2, 0, [ENT]. Note: While the [RECEIVER] button is flashing, the input source cannot be changed by using the remote controller.
0
ENT DIMMER
CLR
SLEEP
SP A / B
MUTING
ENTER
ENTER PLAYLIST/CAT PLAYLIST/CAT
RETURN
RETURN SETUP
43
Listening to the Radio—Continued
SAT
ENTER
PLAYLIST/CAT
ENTER PLAYLIST/CAT
TUNER
TUNING
MASTER VOLUME
TUNING PRESET
RETURN
RETURN SETUP
STANDBY/ON
STANDBY
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
LISTENING MODE
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
STEREO
SURROUND
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVELLEVEL+
CLEAR
DISPLAY DISPLAY RETURN TUNING MODE Selecting XM Channels from the Front Panel:
DISPLAY VCR
L NIGHT DVD
CINE FLTR HDD
RC-647M
Displaying XM Radio Information
1
TUNING MODE
Press the [TUNING MODE] button to select “Channel Search” or “Category Search” mode.
1
AV receiver
DISPLAY
Press the [DISPLAY] button repeatedly to cycle through the available information.
2
ENTER
Press the [ENTER] button repeatedly to select a category.
Remote controller
DISPLAY
3
TUNING PRESET
Use the TUNING Up and Down [ ]/[ ] buttons to select a channel. In Channel Search mode, you can select any channel. In Category Search mode, you can only select channels from the currently selected category.
The following information can be displayed:
Channel name
Channel number & preset number Selecting the Previous Channel:
1
AV receiver
RETURN
To listen to the previously selected XM channel, press the [RETURN] button.
Category
Artist
Song title
Remote controller
Listening mode
RETURN
Notes: • If the category, artist, or song title is not available, “- - -” will be displayed instead. • The listening mode is displayed only when speaker set A is on.
44
Listening to the Radio—Continued
ENTER TUNING
MASTER VOLUME
TUNING PRESET
XM Radio Messages
The following messages may appear while using XM radio.
STANDBY/ON
STANDBY
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
SETUP
The XM Passport System is not connected properly. Check the connection.
Positioning the XM Passport System
You can check the signal strength of the XM radio signal and adjust the position of the XM Passport System accordingly. The XM user encryption code is being updated. Please wait.
1
SETUP
On the AV receiver, press the [SETUP] button.
2
TUNING PRESET
Use the Up and Down [ ]/[ ] buttons to select “5. ANT Aiming,” and then press [ENTER].
The signal is too weak. Check the XM Passport System connection and reposition it for the best reception.
The AV receiver is tuning or decoding audio or text data. Please wait.
3
Adjust the position of the XM Passport System so that the SAT signal strength bar is as long as possible. The XM channel you selected is not currently broadcasting. Select another channel. If you can’t receive a satellite signal, press the Down [ ] button to display the terrestrial (TER) signal strength meter and adjust your XM Passport System so that the bar is as long as possible. Terrestrial signals are only available in certain areas.
So long as the signal strength is good, you can enjoy XM Radio by using either satellite or terrestrial reception.
45
Common Functions
This section explains functions that can be used with any input source.
Adjusting the Bass and Treble
You can adjust the bass and treble for the front speakers, except when the Direct or Pure Audio (not North American models) listening mode is selected.
ON/STANDBY
REMOTE MODE
RECEIVER
TAPE
DVD
M D/CDR
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
HDD
Press [RECEIVER] first
1
TONE
4 7
TAPE
5
MULTI CH
6
DVD
TV
Press the AV receiver’s [TONE] button repeatedly to select either Bass or Treble.
8
TUNER
9
CD
VCR
12
CABLE
10
11
DIMMER
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
SLEEP
--/---
2
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
Use the TONE [–]/[+] buttons to adjust.
VOL
PREVIOUS MENU
MUTING
SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT
RETURN
SETUP
■ Bass You can boost or cut low-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps. ■ Treble You can boost or cut high-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps.
LISTENING MODE STEREO SURROUND
AUDIO SUBTITLE RANDOM REPEAT
CH SEL
TEST TONE
CH SEL PLAY MODE
LEVEL-
LEVEL+
LEVEL – +
L NIGHT CINE FLTR HDD DVD
DISPLAY VCR
RC-647M
Note: • To bypass the bass and treble tone circuits, select the Direct or Pure Audio (not North American model) listening mode.
Muting the AV Receiver
TONE, –, +
MASTER VOLUME
TUNING PRESET
You can temporarily mute the output of the AV receiver. Press the remote controller’s [MUTING] button. The output is muted and the MUTING indicator flashes on the display.
STANDBY/ON
STANDBY
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
MUTING
CLEAR
PHONES
DIMMER
Setting the Display Brightness
You can adjust the brightness of the display. Press the remote controller’s [DIMMER] button repeatedly to select: dim, dimmer, or normal brightness. Alternatively, you can use the AV receiver’s [DIMMER] button (not European models).
To unmute the AV receiver, press the remote controller’s [MUTING] button again, or adjust the volume. The output is unmuted and the MUTING indicator goes off. Muting is cancelled when the AV receiver is set to Standby.
DIMMER
46
Common Functions—Continued
Using the Sleep Timer
With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. Press the remote controller’s [SLEEP] button repeatedly to select the required sleep time. You can set the sleep time from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears.
SLEEP indicator
Adjusting Speaker Levels
You can adjust the volume of each speaker in speaker set A. These temporary adjustments are cancelled when the AV receiver is set to Standby.
1
CH SEL
SLEEP
Use the remote controller’s [CH SEL] button to select each speaker, and use the [LEVEL–] and [LEVEL+] buttons to adjust the volume. You can adjust the volume of each speaker from –12 dB to +12 dB (–15 dB to +12 dB for the subwoofer).
LEVEL-
LEVEL+
To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you’ll shorten the sleep time by 10 minutes.
Notes: • You cannot use this function while the AV receiver is muted. • Speakers that are set to No or None in the Speaker Configuration cannot be adjusted. ■ Speaker Set B While speaker set B is on, you can adjust the volume of the left and right speakers, from –12 dB to +12 dB.
Using Headphones
For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver’s PHONES jack.
STANDBY/ON
STANDBY
• These settings are stored when the AV receiver is set to Standby. • While speaker set B is on, you cannot adjust the levels of speaker set A’s surround back speakers. ■ Headphones While a pair of headphones is connected, you can adjust the volume of each headphone speaker, from –12 dB to +12 dB each.
PHONES
Notes: • Always turn down the volume before connecting your headphones. • Speaker sets A and B are turned off while the headphones plug is inserted in the PHONES jack. • When you connect a pair of headphones, the listening mode is set to Stereo, unless it was set to Pure Audio, Mono, Stereo, or Direct, in which case it stays the same. • When the multichannel DVD input is selected, only the front left and front right channels can be heard in the headphones.
• These settings are stored when the AV receiver is set to Standby.
47
Using the Listening Modes
Selecting Listening Modes
For a description of each listening mode, see “About the Listening Modes” on page 50.
• The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial or optical). • Listening mode availability depends on the format of the current input signal. • While a pair of headphones is connected, you can select only the Pure Audio (not North American model), Mono, Direct, or Stereo listening mode. • The listening modes cannot be selected while speaker set A is off.
Selecting with the Remote Controller
TV INPUT
GUIDE TOP MENU PREVIOUS MENU
VOL
DISC ALBUM
CH
VOL
SP A / B
MUTING
ENTER PLAYLIST/CAT PLAYLIST/CAT
RETURN
SETUP
SURROUND
LISTENING MODE
STEREO
STEREO
SURROUND
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD CINE FLTR HDD LEVELLEVEL+
,
RC-647M
Selecting on the AV Receiver
MASTER VOLUME
TUNING PRESET
■ [STEREO] button This button selects the Stereo listening mode. ■ [SURROUND] button This button selects the Dolby Digital and DTS listening modes and the Neural Surround listening mode (North American model only). ■ LISTENING MODE [ ]/[ ] buttons Pressing these buttons repeatedly cycles through all of the listening modes that can be used with the current input source.
STANDBY/ON
STANDBY
ENTER
PURE AUDIO
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
PURE AUDIO STEREO LISTENING MODE
■ [PURE AUDIO] button (not North American model) This button selects the Pure Audio listening mode. When this mode is selected, the AV receiver outputs no video signals and its display is turned off. Pressing this button again will select the previous listening mode. ■ [STEREO] button This button selects the Stereo listening mode. ■ LISTENING MODE [ ]/[ ] buttons Pressing these buttons repeatedly cycles through all of the listening modes that can be used with the current input source.
48
Using the Listening Modes—Continued
The following table shows which listening modes can be used with each input signal format.
Source format Analog, PCM*1 CD, TV, radio, cassette, etc. 3/2.1 2/2.1 Dolby Digital 2/0 1/0, 1+1 Other 3/2.1 2/2.1 DTS/DTS 96/24*2 DTS-ES 2/0 Discrete Matrix Multich analog
DVD, DTV, etc.
DVD, CD, etc.
DVD
Listening mode Pure Audio (Not North American models) Direct Stereo Mono Multich PLIIx Movie/Music/Game *3 Neo:6 Cinema Neo:6 Music Neural Surround (North American models only) Dolby D Dolby D + Neo:6 Dolby D EX Dolby D+PLIIx Music Dolby D+PLIIx Movie DTS, DTS 96/24 DTS-ES Discrete DTS DTS-ES Matrix DTS+Neo:6 DTS+Dolby EX DTS+PLIIx Music DTS+PLIIx Movie Mono Movie Orchestra Unplugged Studio-Mix TV Logic All Ch Stereo Full Mono Dolby
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔ ✔ ✔*4 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
*6
✔
✔
✔
✔*5
Onkyo Original DSP
✔
✔
✔
✔
✔
✔
✔
✔
*1. In the Pure Audio and Direct listening modes, 32 kHz, 44.1 kHz, and 48 kHz PCM is processed at 64 kHz, 88.2 kHz, and 96 kHz respectively. In listening modes other than Pure Audio, Direct, and Stereo, 64 kHz, 88.2 kHz, and 96 kHz PCM is processed at 32 kHz, 44.1 kHz, and 48 kHz respectively. *2. In listening modes other than Pure Audio, Direct, Stereo, and DTS 96/24, DTS 96/24 sources are processed as normal DTS. *3. If the Surr Back parameter is set to None, or speaker set B is on, normal Pro Logic II is used. *4. Not available for 88.2 kHz and 96 kHz PCM input signals. *5. If the Surr Back setting is set to None, or speaker set B is on, normal DTS is used. *6. Available only when surround speakers are connected.
: Only available on 6.1/7.1-channel playback systems. Not available while speaker set B is on. : Only available on 7.1-channel playback systems. Not available while speaker set B is on.
Tip: To check the format of the digital input signal, see “Displaying Source Information” on page 37.
49
Using the Listening Modes—Continued
About the Listening Modes
The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.
The illustration shows which speakers are active in each listening mode with 7.1 channel speaker system.
Front left Center Front right
Dolby Digital
Use this mode with DVDs that bear the Dolby Digital logo, and Dolby Digital TV broadcasts. This is the most common digital surroundsound format, and it’ll put you right in the middle of the action, just like being in a movie theater or concert hall.
Dolby Digital EX DTS+Dolby EX
Subwoofer
Surround left
Surround back left/ right
Surround right
Pure Audio (not North American models)
In this mode, the display and video circuitry are turned off, minimizing possible noise sources for the ultimate in high-fidelity reproduction. (As the video circuitry is turned off, no video signals are output in this mode.)
Direct
These modes expand 5.1-channel Dolby Digital and DTS sources for 6.1/7.1-channel playback. They’re especially suited to Dolby Digital EX soundtracks that include a matrix-encoded surround back channel. The additional channel adds an extra dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects. Use them with DVDs that bear the Dolby Digital or DTS logo.
Dolby Digital+PLIIx Music DTS+PLIIx Music
In this mode, audio from the input source is output directly with minimal processing, providing high-fidelity reproduction. All of the source’s audio channels are output as they are.
Stereo
These modes use the Pro Logic IIx Music mode to expand 5.1-channel Dolby Digital and DTS sources for 6.1/7.1-channel playback. Use them with Dolby Digital or DTS 5.1 music sources (e.g., DVD and Dolby Digital TV broadcasts).
Dolby Digital+PLIIx Movie DTS+PLIIx Movie
Sound is output by the front left and right speakers and subwoofer.
Mono
Use this mode when watching an old movie with a mono soundtrack, or use it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs.
Dolby Pro Logic IIx Dolby Pro Logic II
These modes use the Pro Logic IIx Movie mode to expand 5.1-channel Dolby Digital and DTS sources for 7.1-channel playback. Use them with Dolby Digital and DTS 5.1 movies (e.g., DVD and select digital TV broadcasts).
DTS
The DTS digital surround-sound format supports up to 5.1 discrete channels and uses less compression for high-fidelity reproduction. Use it with DVDs and CDs that bear the DTS logo.
DTS 96/24
Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging. If you’re not using any surround back speakers, Dolby Pro Logic II will be used instead of Dolby Pro Logic IIx.
• PLIIx Movie
This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo.
DTS-ES Discrete
Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g., TV, DVD, VHS).
• PLIIx Music
Use this mode with any stereo or Dolby Surround (Pro Logic) music source (e.g., CD, radio, cassette, TV, VHS, DVD).
• PLIIx Game
This mode is for use with DTS-ES Discrete soundtracks, which use a discrete surround back channel for true 6.1/7.1-channel playback. The seven totally separate audio channels provide better spatial imaging and 360-degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Discrete soundtrack.
Use this mode with video games, especially those that bear the Dolby Pro Logic II logo.
50
Using the Listening Modes—Continued
DTS-ES Matrix
Onkyo Original DSP Modes
Mono Movie
This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.
DTS Neo:6
This mode is suitable for old movies and other mono sources. The center speaker outputs the sound as it is, while reverb is applied to the sound output by the other speakers, giving presence to even mono material.
Orchestra
This mode expands any 2-channel source for 6.1-channel playback. It uses six full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.
• Neo:6 Cinema
Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.
Unplugged
Use this mode with any stereo movie (e.g., TV, DVD, VHS).
• Neo:6 Music
Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage.
Studio-Mix
Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS, DVD).
Dolby Digital + Neo:6 DTS+Neo:6
This mode uses Neo:6 to expand 5.1-channel Dolby Digital and DTS sources for 6.1/7.1-channel playback. Use it with DVDs that bear the Dolby Digital or DTS logo and feature a 5.1-channel soundtrack.
Neural Surround (North American models only)
Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.
TV Logic
This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire sound, and clarity to voices.
All Ch Stereo
Neural Surround represents the latest advancement in surround technology developed for music and is adopted by XM Satellite Radio for digital radio broadcast of surround recordings and live events in surround sound. Neural Surround employs psychoacoustic frequencydomain processing, which allows delivery of a more detailed sound stage, with superior channel separation and localization of audio elements. System playback is scalable from 5.1 to 7.1 multichannel surround playback.
Ideal for background music, this mode fills the entire listening area with stereo sound from the front, surround, and surround back speakers.
Full Mono
In this mode, all speakers output the same sound in mono, so the sound you hear is the same regardless of where you are within the listening room.
51
Using the Listening Modes—Continued
Using the CinemaFILTER
ON/STANDBY REMOTE MODE
RECEIVER
TAPE
DVD
M D/CDR
RECEIVER
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
HDD
4 7
TAPE
5
MULTI CH
6
DVD
TV
8
TUNER
9
CD
VCR
12
CABLE
10
11
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
With the CinemaFILTER, you can soften overly bright movie soundtracks, which are typically mixed for reproduction in a movie theater. CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital EX, PLII/IIx Movie, DTS, DTS-ES, DTS Neo:6 Cinema, DTS 96/24, Dolby/DTS+PLIIx Movie, Dolby/DTS+Neo:6, and DTS+Dolby EX.
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
VOL
PREVIOUS MENU
1
RECEIVER
SP A / B
MUTING
ENTER
PLAYLIST/CAT RETURN
ENTER PLAYLIST/CAT
SETUP
SETUP
CINE FLTR
Press the [RECEIVER] REMOTE MODE button, and then press the [CINE FLTR] button repeatedly to select: On: CinemaFILTER on. Off: CinemaFILTER off.
LISTENING MODE STEREO SURROUND
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD CINE FLTR HDD LEVELLEVEL+
Using the Audio Adjust Settings
CINE FLTR L NIGHT
The Audio Adjust settings only affect speaker set A.
RC-647M
1
RECEIVER
Press the [RECEIVER] button followed by the [SETUP] button.
Using the Late Night Function (Dolby Digital only)
With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.
SETUP
2
Use the Up and Down [ ]/[ ] buttons to select “4. Audio Adjust,” and then press [ENTER].
1
RECEIVER
L NIGHT
Press the [RECEIVER] REMOTE MODE button, and then press the [L NIGHT] button repeatedly to select: Off: Late Night function off. Low: Small reduction in dynamic range. High: Big reduction in dynamic range.
3
Use the Left and Right [ ]/[ ] buttons to change the setting. Press the Down [ ] button to select the next setting. Repeat this step for the other settings.
Notes: • The effect of the Late Night function depends on the Dolby Digital material that you are playing, and with some material there will be little or no effect. • The Late Night function is set to Off when the AV receiver is set to Standby.
52
Using the Listening Modes—Continued
4
SETUP
Press the [SETUP] button. Setup closes.
adjusts the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. It can be adjusted from 0 to 7 (default value is 3).
DTS Neo:6 Music Mode Setting
■ Center Image The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel (stereo) sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. It can be adjusted from 0 to 5 (default value is 2). This setting has no effect if no center speaker is connected. When set to 0, the front left and right channel output is attenuated by half (–6 dB), giving the impression that the sound is located centrally. This setting works well when the listening position is considerably off center. When set to 5, the front left and right channels are not attenuated, maintaining the original stereo balance.
The Audio Adjust settings are explained below.
Input Channel Settings
■ Multiplex This setting determines which channel is output from a stereo multiplex source. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on. Main: The main channel is output (default). Sub: The sub channel is output. M/S: Both the main and sub channels are output. ■ Mono (2ch) This setting determines which channel is output when the Mono listening mode is used with a stereo source. L+R: Both the left and right channels are output (default). L: Only the left channel is output. R: Only the right channel is output.
Dolby Digital EX Input Signal Setting
■ Dolby EX This setting determines how Dolby Digital EX signals are handled. This setting is unavailable if no surround back speakers are connected or speaker set B is on. Auto: If the source signal contains a Dolby Digital EX flag, the Dolby Digital EX listening mode is used (default). Manual: You can select Pro Logic IIx Movie, Pro Logic IIx Music, Dolby Digital, or Dolby Digital EX.
PLII and PLIIx Music Mode Settings
These settings apply to only 2-channel (stereo) sources. ■ Panorama With this setting, you can broaden the width of the front stereo image when using the Pro Logic II Music or Pro Logic IIx Music listening mode. On: Panorama function on. Off: Panorama function off (default). ■ Dimension With this setting, you can move the sound field forward or backward when using the Pro Logic II Music or Pro Logic IIx Music listening mode. The default value is 3. It can be adjusted from 0 to 6. Higher settings move the sound field forward. Lower settings move it backward. If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward. ■ Center Width With this setting, you can adjust the width of the sound from the center speaker when using the Pro Logic II Music or Pro Logic IIx Music listening mode. Normally, the center channel sound is output by only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting
Multichannel Subwoofer Setting
■ SW Sens On some DVD players, the signal from the multichannel subwoofer output is 15 dB higher than normal. You can change the subwoofer sensitivity to match your DVD player. Note that this setting only affects signals connected to the SUBWOOFER input jack of the multichannel DVD input. You can select 0 dB (default), +5 dB, +10 dB, or +15 dB. If you find that your subwoofer is too loud, try the +10 dB or +15 dB setting.
53
Recording
This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources.
Recording Audio and Video from Separate Sources
You can overdub audio onto your video recordings by simultaneously recording audio and video from two separate sources. This is possible because only the audio source is switched when an audio-only input source, such as TAPE, TUNER, or CD, is selected, the video source remains the same. In the following example, audio from the CD player connected to the CD IN jacks, and video from the camcorder connected to the VIDEO 3 INPUT VIDEO jack are recorded by the VCR connected to the VIDEO 1 OUT jacks.
VIDEO 3 INPUT
VIDEO L AUDIO R
Recording the Input Source
You can only record to a component that’s connected to the TAPE OUT or VIDEO 1 OUT jacks. See pages 20–31 for information on connecting your AV components.
1
DVD VIDEO 1 VIDEO 2 VCR VIDEO 3 TAPE TUNER
CD
Remote controller
1
V1
Use the input selector buttons to select the component that you want to record. Audio signals from the selected input source are output by the TAPE OUT and VIDEO 1 OUT jacks. You can listen to the source while recording. The AV receiver’s VOLUME control has no effect on recording.
Camcorder video signal audio signal
XM
2
V2
3
V3
6
DVD
7
TAPE
8
TUNER
9
CD
AM
ANTENNA
FM 75
SURROUND BAC SPEAKERS
DIGITAL IN COA XIAL OPTICAL 1
VIDEO 2 IN VIDEO 1 IN
COMPONENT VIDEO
DVD IN
L
OUT
Y VIDEO 2 PB VIDEO 1 DVD MONITOR OUT
V
R
2 3
On your recorder, start recording. Start playback on the source component.
2
PR
S
IN
OUT OUT
IN IN
IN
FRONT SURROUND CENTER SURR BACK
3
IN
OUT
IN
IN
L
REMOTE CONTROL
L
L
R
R
R
SUB WOOFER
CD
TAPE
VIDEO 2
VIDEO 1
DVD
Notes: • You cannot record from a component that’s connected to a digital input. Only analog inputs can be recorded. • The surround sound effects provided by the listening modes cannot be recorded. • You cannot record from a component that’s connected to the multichannel DVD input. • If you select another input source while recording, that input source will be recorded instead. • While the Pure Audio listening mode is selected, the VIDEO 1 OUT V and S jacks don’t output video signals, so select another mode when recording.
CD player
VCR
1. Prepare the camcorder and CD player for playback. 2. Prepare the VCR for recording. 3. Press the [VIDEO 3] input selector button. 4. Press the [CD] input selector button.
This selects the CD player as the audio source, but leaves the camcorder as the video source.
5. Start recording on the VCR, then start playback on the camcorder and CD player.
Video from the camcorder and audio from the CD player are recorded by the VCR.
The Crossover Frequency, Double Bass, and Speaker Distance settings cannot be changed while a pair of headphones is connected, speaker set B is on, or the multichannel DVD input is being used.
Over 8 in. (20 cm) 6-1/2 to 8 in. (16–20 cm) 5-1/4 to 6-1/2 in. (13–16 cm)
Crossover Frequency
This setting only applies to the speakers that you specified as Small in the “Speaker Configuration” on page 34. To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers.
3-1/2 to 5-1/4 in. (9–13 cm) Under 3-1/2 in. (9 cm)
*Choose the setting suitable for the speaker.
Continue with step 4 of the “Double Bass” setting below. Notes: • For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly. • Choose a higher crossover frequency if you want more sound from your subwoofer.
1
RECEIVER
Press the [RECEIVER] REMOTE MODE button, followed by the [SETUP] button.
SETUP
2
Use the Up and Down [ ]/[ ] buttons to select “1. SP Config,” and then press [ENTER].
Double Bass
With the Double Bass function, you can boost bass output by feeding bass sounds from the front left and right channels to the subwoofer. This function can only be set if in the Speaker Configuration on page 34, the Subwoofer setting is set to Yes (step 3), and the Front setting is set to Large (step 4).
4 3
Use the Down [ ] button to select “Crossover,” and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency. Use the diameter of the smallest speaker in your system when choosing the crossover frequency.
Use the Down [ ] button to select “Double Bass,” and then use the Left and Right [ ]/[ ] buttons to select: On: Double Bass function on. Bass from the front left and right channels is also fed to the subwoofer (default). Off: Double Bass function off.
5
SETUP
Press the [SETUP] button. Setup closes.
55
Advanced Setup—Continued
Speaker Distance
With these settings, you can specify the distance from each speaker to the listening position. example, if the Front distance is set to 20 ft. (6 m), the Center and Subwoofer distances can be set between 15 and 25 ft. (4.5 and 7.5 m). • The Surround and Surround Back distances can be set up to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the Front distance. For example, if the Front distance is set to 20 ft. (6 m), the SurrRight, Surr Left, Surr Back R, and Surr Back L distances can be set between 5 and 25 ft. (1.5 and 7.5 m).
1 2
Measure and make a note of the distance from each speaker to the listening position. Press the [RECEIVER] REMOTE MODE button, followed by the [SETUP] button.
RECEIVER
Speaker Levels
SETUP
You can set the volume level of each speaker so that all speakers can be heard equally at the listening position. Use the Up and Down [ ]/[ ] buttons to select “2. SP Distance,” and then press [ENTER].
The speaker levels cannot be adjusted while a pair of headphones is connected, speaker set B is on, or the AV receiver is muted.
3
1 4
While “Unit” is displayed, use the Left and Right [ ]/[ ] buttons to select “feet” or “meters”. feet: Distances can be set in feet. Range: 1 to 30 feet in 1-foot steps. meters: Distances can be set in meters. Range: 0.3 to 9 meters in 0.3-meter steps. Use the Down [ ] button to select “Front,” and use the Left and Right [ ]/[ ] buttons to specify the distance for the front speakers, then press the Down [ ] button to select the next speaker. Repeat step 5 for all speakers. Note: Speakers that you set to No or None in the Speaker Configuration (page 34) cannot be selected. Press the [SETUP] button. Setup closes.
RECEIVER
Press the [RECEIVER] REMOTE MODE button, followed by the [SETUP] button.
SETUP
2
Use the Up and Down [ ]/[ ] buttons to select “3. Level Cal,” and then press [ENTER]. A pink noise test tone is output by the front left speaker.
5
3
6
Turn up the volume so that you can hear the test tone sufficiently. As each speaker outputs the test tone, its name appears on the display.
7
Notes: • The Center and Subwoofer distances can be set up to 5 ft. (1.5 m) more or less than the Front distance. For
56
Advanced Setup—Continued
4
Use the Left and Right [ ]/[ ] buttons to adjust the speaker level, and use the Down [ ] button to select the next speaker. The levels can be adjusted from –12 to +12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).
Digital Input Signal Formats
The following table shows the display indicator for each digital signal format.
Format Dolby Digital DTS PCM PCM Display
5
Repeat step 4 so that the level of the test tone coming from each speaker is the same. Speakers that you set to No or None in the Speaker Configuration (page 34) do not output the test tone. Press the [SETUP] button. Setup closes. Don’t forget to turn down the volume if you turned it up while setting the levels.
Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can specify the signal format as either PCM or DTS: • If the beginnings of tracks from a PCM source are cut off, try the PCM setting. • If noise is produced when fast forwarding or reversing a DTS CD, try the DTS setting.
6
SETUP
MASTER VOLUME
TUNING PRESET
STANDBY/ON
STANDBY
ENTER
MULTI CH
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
RETURN
SETUP
VCR
Note: • A quick way to adjust the speaker levels is to press the remote controller’s [TEST TONE] button to turn on the test tone, use the [LEVEL–] and [LEVEL+] buttons to adjust the levels, and use the [CH SEL] button to select the speakers.
VIDEO 3 INPUT PHONES
SPEAKERS A B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R
CLEAR
DIGITAL INPUT
1 2
Press and hold the AV receiver’s [DIGITAL INPUT] button for about 3 seconds. While “Auto” is displayed (about 3 seconds), press the [DIGITAL INPUT] button repeatedly to select: PCM, DTS, or Auto. PCM: Only PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and there will be no sound. DTS: Only DTS format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.
57
Advanced Setup—Continued
Correcting Sound and Picture Sync
When using progressive scanning on your DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals. You can set it from 0 to 100 milliseconds (ms) in 20 millisecond steps.
ON/STANDBY
REMOTE MODE
RECEIVER
TAPE
DVD
M D/CDR
RECEIVER
INPUT SELECTOR
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
HDD
4 7
TAPE
5
MULTI CH
6
DVD
TV
8
TUNER
9
CD
VCR
12
CABLE
10
11
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
VOL
PREVIOUS MENU
SP A / B
MUTING
ENTER PLAYLIST/CAT PLAYLIST/CAT
RETURN
SETUP
1
RECEIVER
Press the [RECEIVER] REMOTE MODE button.
2
1
V1
2
V2
3
V3
6
DVD
Press and hold, for more than 4 seconds, the input selector button for the input source that you want to correct. This can be the [DVD], [VIDEO 1], [VIDEO 2], or [VIDEO 3] input source. Use the Left and Right [ ]/[ ] buttons to adjust the delay from 0 to 100 milliseconds in 20 millisecond steps.
3
Note: • This setting is not available when the Pure Audio listening mode is used, or the Direct listening mode is used with an analog input signal.
58
Controlling Other Components
You can use the AV receiver’s remote controller (RC-647M) to control your other AV components, including those made by other manufacturers. This section explains how to enter the necessary remote control code for the component that you want to control (e.g., DVD player, TV, or VCR).
2
REMOTE MODE
DVD
M D/CDR
CD
HDD
While holding down the REMOTE MODE button that you want to set, press the [DISPLAY] button for 3 seconds. The REMOTE MODE button lights up.
TV
Entering Remote Control Codes
To control another component, you must first enter the appropriate remote control code to a REMOTE MODE button. You’ll need to enter a code for each component that you want to control.
VCR
CABLE
SAT
DISPLAY
ON/STANDBY
REMOTE MODE
RECEIVER
1
V1
RECEIVER
TAPE
DVD
M D/CDR
INPUT SELECTOR
2
V2
3
V3
CD
HDD
REMOTE MODE
3
1
V1
Number buttons
D TUN
4 7
TAPE
5
MULTI CH
6
DVD
TV
2
V2
3
V3
8
TUNER
9
CD
VCR
12
CABLE
4 7
TAPE
5
MULTI CH
6
DVD
10
11
Within 30 seconds, use the number buttons to enter the 4-digit remote control code. The REMOTE MODE button flashes twice.
+10
--/---
0
ENT DIMMER
CLR
SLEEP
SAT
8
TUNER
9
CD
11
TV INPUT
GUIDE TOP MENU PREVIOUS MENU
VOL
DISC ALBUM
CH
0
VOL
DIMMER ENT
SP A / B
MUTING
ENTER PLAYLIST/CAT PLAYLIST/CAT
4
RETURN
SETUP
LISTENING MODE STEREO SURROUND
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVELLEVEL+
DISPLAY
DISPLAY VCR
L NIGHT DVD
CINE FLTR HDD
L NIGHT
Press the REMOTE MODE button again to select the remote controller mode, point the remote controller at the component, and check the operation. If the remote controller doesn’t work as expected, and several remote codes are listed, try each one in turn and use the one that works best.
RC-647M
Notes: • A remote control code cannot be entered for the [RECEIVER] REMOTE MODE button. • The remote control codes provided are correct at the time of printing, but are subject to change.
1
Look up the appropriate remote control code in the separate Remote Control Codes list. The codes are organized by category (e.g., DVD player, TV, etc.).
59
Controlling Other Components—Continued
Remote Control Codes for Onkyo Components Connected via
Onkyo components that are connected via are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.
Resetting REMOTE MODE Buttons
You can reset a REMOTE MODE button to its default remote control code.
1
REMOTE MODE
DVD
1
Make sure the Onkyo component is connected with an cable and an analog audio cable (RCA). See page 31 for details. Enter the appropriate remote control code for the [DVD] or [CD] REMOTE MODE button. [DVD] REMOTE MODE button 1612: Onkyo DVD player with [CD/MD/CDR/HDD] REMOTE MODE button 1327: Onkyo CD player with 1808: Onkyo MD recorder with 1322: Onkyo CD recorder with 1993: HDD-compatible component with See the previous page for how to enter remote control codes.
M D/CDR
CD
HDD
While holding down the REMOTE MODE button that you want to reset, press the [L NIGHT] button for 3 seconds. The REMOTE MODE button lights up.
TV
2
VCR
CABLE
SAT
L NIGHT
2
REMOTE MODE
DVD
M D/CDR
Press the REMOTE MODE button again. The REMOTE MODE button flashes twice, indicating that it’s been reset.
CD
3
Press the [DVD] or [CD] REMOTE MODE button, point the remote controller at the AV receiver, and operate the component.
HDD
TV
VCR
If you want to control an Onkyo component by pointing the remote controller directly at it, or you want to control an Onkyo component that’s not connected via , use the following remote control codes: [DVD] REMOTE MODE button 0627: Onkyo DVD player without (default) [CD/MD/CDR/HDD] REMOTE MODE button 1817: Onkyo CD player without (default) 0868: Onkyo MD recorder without 1323: Onkyo CD recorder without 1990: HDD-compatible component without Note: If you connect an -capable Onkyo MD recorder, CD recorder, or HDD-compatible component to the TAPE IN/OUT or VIDEO 2 jacks, for remote operation to work properly, you must set the Input Display to MD, CDR, or HDD (see page 33).
CABLE
SAT
The [DVD] and [CD] REMOTE MODE buttons are preprogrammed with remote control codes for controlling Onkyo DVD players and CD players respectively. When these buttons are reset, the preprogrammed code is restored.
Resetting the Remote Controller
You can reset the remote controller to its default settings.
1
RECEIVER
L NIGHT
While holding down the [RECEIVER] REMOTE MODE button, press the [L NIGHT] button for 3 seconds. The [RECEIVER] button lights up.
2
RECEIVER
Press the [RECEIVER] REMOTE MODE button again. The [RECEIVER] button flashes twice, indicating that it’s been reset.
60
Controlling Other Components—Continued
To control another component, point the remote controller at it and use the buttons explained below. (You must select the appropriate remote control mode first.) With some AV components, certain buttons may not work as expected, and some may not work at all. ■ Controlling a TV ■ Controlling a VCR ■ Controlling a Satellite or Cable Receiver
A
ON/STANDBY REMOTE MODE
ON/STANDBY
A
REMOTE MODE
ON/STANDBY
A
REMOTE MODE
RECEIVER
TAPE
DVD
M D/CDR
RECEIVER
TAPE
DVD
M D/CDR
RECEIVER
TAPE
DVD
M D/CDR
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
HDD
4 7
TAPE
5
MULTI CH
6
DVD
TV
Press [TV] first
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
HDD
2
Press [VCR] first
D TUN
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
HDD
2
Press [SAT] first
4 7
TAPE
5
MULTI CH
6
DVD
TV
4 7
TAPE
5
MULTI CH
6
DVD
TV
8
TUNER
9
CD
VCR
12
CABLE
10
11
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
2 3 4 5 6 7
8
TUNER
9
CD
VCR
12
CABLE
8
TUNER
9
CD
VCR
12
CABLE
10
11
10
11
+10
D TUN
0
ENT DIMMER
CLR
SLEEP
SAT
+10
--/---
0
ENT DIMMER
CLR
SLEEP
SAT
--/---
3
VOL
PREVIOUS MENU
TV INPUT
GUIDE TOP MENU
VOL
DISC ALBUM
CH
VOL
INPUT
PREVIOUS MENU
TV
VOL
DISC ALBUM
CH
TV INPUT
VOL
DISC ALBUM
CH
VOL
GUIDE TOP MENU
4
GUIDE TOP MENU
PREVIOUS MENU
SP A / B
MUTING
SP A / B
MUTING
SP A / B
MUTING
ENTER PLAYLIST/CAT PLAYLIST/CAT
ENTER PLAYLIST/CAT PLAYLIST/CAT PLAYLIST/CAT
ENTER PLAYLIST/CAT
RETURN
SETUP
RETURN
SETUP
RETURN
SETUP
5
LISTENING MODE STEREO SURROUND
3 4 5 6 7 8 9
LISTENING MODE STEREO SURROUND
6
LEVEL+ CINE FLTR HDD
LISTENING MODE STEREO SURROUND
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD CINE FLTR HDD LEVELLEVEL+
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD LEVEL-
AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD CINE FLTR HDD LEVELLEVEL+
A [ON/STANDBY], TV [ B Number buttons
Enter numbers.
]* Sets the TV to On or Standby.
A [ON/STANDBY]
Sets the VCR to On or Standby.
A [ON/STANDBY]
Sets the satellite/cable receiver to On or Standby.
B Number buttons
Select channels.
B Number buttons
Enter numbers.
C TV VOL [ ]/[ ]*
Adjusts the TV’s volume.
C [CLR]
Cancels functions.
C [CLR]
Cancels functions.
D [CH +/–]
Selects channels on the TV.
D [CH +/–]
Selects channels on the VCR.
D [CH +/–]
Selects satellite/cable channels.
E [PREVIOUS]
Selects the previous channel.
E [ ], [ ], [ ]
Pause, Play, Stop.
E [PREVIOUS]
Selects the previous channel.
F [TV INPUT]*
Selects the TV’s VCR input.
F [
], [ ]
], [ ] Rewind and Fast forward.
F [GUIDE]
Displays the program guide.
G [ ], [ ], [ ], [
Operates the VCR.
G [ENTER]
Confirms the selection.
* Buttons marked with an asterisk (*) are exclusively for controlling a TV and can be used at anytime regardless of the current remote controller mode.
H [ ]/[ ]/[ ]/[ ]
Selects menu items.
I [ ], [ ], [ ], [
Operates the VCR.
], [
]
61
Troubleshooting
If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting your Onkyo dealer.
To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VIDEO 1] button, press the [STANDBY/ON] button. “Clear” will appear on the display and the AV receiver will enter Standby mode.
VIDEO 1
STANDBY/ON
•
•
•
•
VCR
Note that resetting the AV receiver will delete your radio presets and custom settings.
•
Power
Can’t turn on the AV receiver • Make sure that the power cord is plugged into the wall outlet properly. • Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again. The AV receiver turns off as soon as it’s turned on • The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact your Onkyo dealer. • •
home theater enjoyment and has a wide volume range for precise adjustment. If the MUTING indicator is shown on the display, press the remote controller’s [MUTING] button to unmute the AV receiver (page 46). While a pair of headphones is connected to the PHONES jack, no sound is output by the speakers (page 47). Check the digital audio output settings on the connected device. On some games consoles, such as those that can play DVDs, the default setting is off. With some DVD-Video discs, you need to select an audio format from a menu. If your turntable doesn’t have a phono preamp built-in, you must connect one between it and the AV receiver. If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer and a phono preamp. Specify the speaker distances and adjust the individual speaker levels (pages 56, 57). The input signal format is set to PCM or DTS. Set it to Auto (page 57).
Only the front speakers produce sound • When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound. • Make sure the speakers are configured correctly (page 34). Only the center speaker produces sound • If you use the Pro Logic IIx Movie, Pro Logic IIx Music, or Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker. • Make sure the speakers are configured correctly (page 34). The surround speakers produce no sound • When the Stereo or Mono listening mode is selected, the surround speakers produce no sound (page 50). • Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode. • Make sure the speakers are configured correctly (page 34). The center speaker produces no sound • When the Stereo or Mono listening mode is selected, the center speaker produces no sound (page 50). • Make sure the speakers are configured correctly (page 34). The surround back speakers produce no sound • While speaker set B is on, speaker set A is reduced to 5.1-channel playback and the surround back speakers produce no sound.
Audio
There’s no sound or it’s very quiet • Make sure that the digital input source is selected properly (page 33). Press the [DIGITAL INPUT] button repeatedly. • Make sure the speker set A or B is on (page 6). • Make sure that all audio connecting plugs are pushed in all the way (page 20). • Make sure that the polarity of the speaker cables is correct, and that the bare wire is in contact with metal part of each speaker terminal (page 17) • Make sure that the speaker cables are not shorting. • Check the volume. It can be set to MIN, 1 through 79, or MAX (page 36). The AV receiver is designed for
62
Troubleshooting—Continued
• The surround back speakers are not used with all listening modes. Select another listening mode (page 50). • Not much sound may be produced by the surround back speakers with some sources. • Make sure the speakers are configured correctly (page 34). The subwoofer produces no sound • The subwoofer outputs no sound while only speaker set B is on. Turn on speaker set A. • When you play source material that contains no information in the LFE channel, the subwoofer produces no sound. • Make sure the speakers are configured correctly (page 34). Speaker set B produces no sound • Speaker set B only outputs sources that are connected to an analog input. Make sure that the analog audio cables are connected properly. There’s no sound with a certain signal format • Check the digital audio output setting on the connected device. On some games consoles, such as those that can play DVDs, the default setting is off. • With some DVD-Video discs, you need to select an audio output format from a menu. Can’t get 6.1- or 7.1-channel playback • While speaker set B is on, speaker set A is reduced to 5.1-channel playback. The volume cannot be set to 79 • When the volume level of each speaker has been adjusted (pages 47, 56), the maximum possible volume may be reduced. Noise can be heard • Using cable ties to bundle audio cables with power cords, speaker cables, and so on may degrade the audio performance, so don’t do it. • An audio cable may be picking up interference. Try repositioning your cables. The Late Night function doesn’t work • Make sure the source material is Dolby Digital (page 52). The multichannel DVD input doesn’t work • Check the multichannel DVD input connections (page 24). • To select the multichannel DVD input, press the [MULTI CH] input selector button. • Check the audio output settings on your DVD player. About DTS signals • When playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction. • When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about 3 seconds, and then resume playback. • With some CD players, you won’t be able to playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.
Video
There’s no picture • Make sure that all video connecting plugs are pushed in all the way (page 20). • Make sure that each video component is properly connected. • The AV receiver does not convert between formats, so if a video source component is connected to a component video input, your TV must be connected to the component video output (page 21). • On your TV, make sure that the video input to which the AV receiver is connected is selected. • While the Pure Audio listening mode (not North American model) is selected, the video circuits are turned off and the AV receiver outputs no video signals.
Tuner
Reception is noisy, stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t appear • Relocate your antenna. • Move the AV receiver away from your TV or computer. • Listen to the station in mono (page 38). • When listening to an AM station, operating the remote controller may cause noise. • Passing cars and airplanes can cause interference. • Concrete walls weaken radio signals. • If nothing improves the reception, install an outdoor antenna.
63
Troubleshooting—Continued
Remote Controller
The remote controller doesn’t work • Make sure that the batteries are installed with the correct polarity (page 11). • Make sure that the remote controller is not too far away from the AV receiver, and that there’s no obstruction between the remote controller and the AV receiver’s remote control sensor (page 11). • Make sure you’ve selected the correct remote controller mode (page 12). • Make sure you’ve entered the correct remote control code (page 59). Can’t control other components • Make sure you’ve selected the correct remote controller mode (page 12). • If you’ve connected an -capable Onkyo MD recorder, CD recorder, or next generation HDD-compatible component to the TAPE IN/OUT jacks, or a DS-A1 Remote Interactive Dock to the VIDEO 2 IN jacks, for the remote controller to work properly, you must set the Input Display to MD, CDR, or HDD (see page 33). • The entered remote control code may not be correct. If more than one code is listed, try each one. • With some AV components, certain buttons may not work as expected, and some may not work at all. • To control an Onkyo component that’s connected via , point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first (see page 60). • To control an Onkyo component that’s not connected via , or another manufacturer’s component, point the remote controller at the component. Be sure to enter the appropriate remote control code first (see page 59).
Others
The sound changes when I connect my headphones • When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, Direct, or Pure Audio (not North American model). The display doesn’t work • The display is turned off when the Pure Audio (not North American model) listening mode is selected. How do I change the language of a multiplex source • Use the “Multiplex” setting on the “4. Audio Adjust” menu to select Main or Sub (page 53). The functions don’t work • To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 31).
Recording
Can’t record • On your recorder, make sure the correct input is selected. • To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (e.g., TAPE IN to TAPE OUT, or VIDEO 1 IN to VIDEO 1 OUT). • When the Pure Audio listening mode is selected, recording is not possible because no video signals are output. Select another listening mode.
64
Troubleshooting—Continued
The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again. Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly. Before disconnecting the power cord from the wall outlet, set the AV receiver to Standby. Memory Backup The AV receiver uses a battery-less memory backup system in order to retain radio presets and other settings when it’s unplugged or in the case of a power failure. Although no batteries are required, the AV receiver must be plugged into an AC outlet in order to charge the backup system. Once it has been charged, the AV receiver will retain the settings for several weeks, although this depends on the environment and will be shorter in humid climates.
The following settings can be made for the S-Video and composite video inputs
You must use the buttons on the unit to make these settings. 1. While holding down the input selector button for the input source that you want to set, press the [SETUP] button. 2. Use the Up and Down [ ]/[ ] buttons to select a setting (see below). 3. Use the Left and Right [ ]/[ ] buttons to change the setting: 4. Press the [SETUP] button when you’ve finished. • Video Attenuation This setting can be made for the DVD, VIDEO 1, VIDEO 2, or VIDEO 3 input. If you have a games console connected to an S-Video or composite video input, and the picture isn’t very clear, you can attenuate the gain. Video ATT:0: (default). Video ATT:2: Gain is reduced by 2 dB. • Outputting S-Video Sources from the Composite Video Outputs This setting can be made for the DVD, VIDEO 1, or VIDEO 2 input. With this setting, you can output S-Video input sources from the composite video outputs, useful if your TV doesn’t have any S-Video inputs. Y/C Mix:Off: S-Video input signals are output by only S-Video outputs (default). Y/C Mix:On: S-Video input signals are output by S-Video outputs and composite video outputs.
65
Specifications
Amplifier Section
Rated Output Power (FTC) All channels: 75 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% 100 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.1% Rated Output Power (IEC) 7 ch × 130 W at 6 ohms, 1 kHz, 1 ch driven Maximum Output Power (JEITA) 7 ch × 160 W at 6 ohms, 1 kHz, 1 ch driven Dynamic Power 180 W + 180 W (3Ω, Front) 140 W + 140 W (4Ω, Front) 95 W + 95 W (8Ω, Front) THD (Total Harmonic Distortion) 0.08% (Power Rated) Damping Factor 60 (Front, 1kHz, 8Ω) Input Sensitivity and Impedance 200 mV/ 47 kΩ (LINE) Output Level and Impedance 200 mV/ 470 Ω (REC OUT) Frequency Response 5 Hz–100 kHz/ +1 dB–3 dB (Direct mode) Tone Control ±10 dB, 80 Hz (BASS) ±10 dB, 20 kHz (TREBLE) Signal to Noise Ratio 100 dB (LINE, IHF-A) Speaker Impedance North American: 6Ω–16Ω Others: 4Ω– or 6Ω–16Ω
General
Power Supply North American: AC 120 V, 60 Hz European: AC 230-240 V, 50 Hz Others: AC 120/220-240 V, 50/60 Hz AC 230-240 V, 50Hz AC 220-230 V, 50/60 Hz North American: 4.9 A European: 570 W Others: 525 W North American: 0.1 W European: 0.2 W Others: 0.5 W 435 × 151 × 377 mm 17-1/8" × 5-15/16" × 14-13/16" North American: 9.6 kg 21.2 lbs. Models with voltage selector: 10.4 kg 22.9 lbs. Others: 10.3 kg 22.7 lbs.
Power Consumption Standby Power Consumption Dimensions (W × H × D) Weight
Video Section
Input Sensitivity/Output Level and Impedance 1 Vp-p /75Ω (Component and S-Video Y) 0.7 Vp-p /75Ω (Component PB/CB, PR/CR) 0.28 Vp-p /75Ω (S-Video C) 1 Vp-p /75Ω (Composite) Component Video Frequency Response 5 Hz – 50 MHz
■ Audio Inputs
Digital Inputs Analog Inputs Multichannel Inputs Optical: 3 Coaxial: 1 DVD (MULTICHANNEL), VIDEO1, VIDEO2, VIDEO3, TAPE, CD 7.1
■ Audio Outputs
Analog Outputs TAPE, VIDEO1 Subwoofer Pre Outputs 1 Speaker Outputs SP A (L, R, C, SL, SR, SBL, SBR) SP B (L, R) Phones 1
Tuner Section
■ FM
Tuning Frequency Range Usable Sensitivity Signal to Noise Ratio THD Frequency Response Stereo Separation North American: 87.5 MHz– 107.9 MHz Other: 87.5 MHz– 108.0 MHz Stereo: 17.2 dBf 2 µV (75Ω IHF) Mono: 11.2 dBf 1 µV (75Ω IHF) Stereo: 70 dB (IHF-A) Mono: 76 dB (IHF-A) Stereo: 0.3% (1 kHz) Mono: 0.2% (1 kHz) 30 Hz–15 kHz / ±1 dB 40 dB (1 kHz)
Specifications and features are subject to change without notice.
■ AM
Tuning Frequency Range Usable Sensitivity Signal to Noise Ratio THD North American: 530 kHz–1710 kHz European: 522 kHz–1611 kHz Others: 522/530 kHz–1611/1710 kHz 300 µV 40 dB 0.7%
66
Memo
67
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/ ONKYO EUROPE UK Office Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452 ONKYO CHINA LIMITED Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung, N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.ch.onkyo.com/
HOMEPAGE http://www.onkyo.com/
I0602-1
SN 29344181
(C) Copyright 2006 ONKYO CORPORATION Japan. All rights reserved.
68
* 2 9 3 4 4 1 8 1 *
Remote Control Codes
1. While holding down the REMOTE MODE button that you want to set, press the [DISPLAY] button for 3 seconds. 2. Use the number buttons to enter the 4-digit remote control code.
REMOTE MODE
DVD
1
M D/CDR
2 5 8 0
3 6 9
CD
HDD
4 DISPLAY 7
TV
VCR
CABLE
SAT
Codes de télécommande
1. Maintenez le bouton REMOTE MODE à initialiser enfoncé et appuyez sur le bouton [DISPLAY] durant 3 secondes.
2. Entrez les 4 chiffres du code de télécommande avec les boutons numériques.
Códigos de control remoto
1. Manteniendo pulsado el botón REMOTE MODE que desee ajustar, pulse el botón [DISPLAY] durante 3 segundos.
2. Utilice los botones de número para introducir el código de 4 dígitos para control remoto.
Codici del telecomando
1. Mentre tenete premuto il pulsante REMOTE MODE che volete impostare, premete il pulsante [DISPLAY] per 3 secondi.
2. Utilizzate i pulsanti numerici per inserire il codice di telecomando a 4 cifre.
Fernbedienungscodes
1. Halten Sie die änderungsbedürftige REMOTE MODE-Taste gedrückt, während Sie die [DISPLAY]-Taste 3 Sekunden lang betätigen.
2. Geben Sie mit den Zifferntasten den 4-stelligen Fernbedienungscode ein.
Afstandsbedieningscodes
1. Houd de REMOTE MODE toets ingedrukt die u wilt instellen en druk dan de [DISPLAY] toets 3 seconden in.
2. Met de cijfertoetsen de 4-cijferige afstandsbedieningscode in.
Fjärrstyrningskoder
1. Tryck in och håll lämplig lägesväljare (REMOTE MODE) intryckt och tryck samtidigt in knappen [DISPLAY] i tre sekunder.
2. In den 4-siffriga fjärrstyrningskoden med hjälp av sifferknapparna.
En Fr Es I t De N l Sv Ct Cs
DVD Codes
DVD Player
Acoustic Solutions Advent Aiwa Akai Akura Amoisonic Amphion Media Works Amstrad AMW Apex Digital Aspire Digital Audiovox Axion Blue Nova International Broksonic Bush Cambridge Soundworks Celestial Changhong CineVision Clayton Coby Conia CyberHome Daewoo Daytek Denver Diamond Dick Smith Electronics Digitor Disney DSE DVD2000 ECC Elta Eltax Emerson Ferguson Funai Gateway GE Go Video Go Vision H&B Harman/Kardon Hitachi iLo Integra Jensen JVC jWin Kiss KLH
Akura Alba Albatron Alfide America Action Amstrad Anam Anam National Anhua Anitech AOC Aolinpike Apex Digital Asuka Audinac Audiosonic Audiovox Aventura Awa Baihe Baile Baird Bang & Olufsen Baohuashi Baosheng Basic Line Baur Baysonic Beijing Beko Bell & Howell BenQ Beon Blaupunkt Blue Sky BPL Bradford
Dainichi Dansai Dayton Dayu De Graaf Decca Dell Denon Dick Smith Electronics Digatron Digital Life Digitor Digix Dixi Dongda Donghai DSE Dumont Durabrand ECE Electroband Elektra Elin Elite Elta Emerson Envision Erres ESA Ether Etron Feilang Feilu Feiyan Feiyue Ferguson Finlandia Finlux Firstar Firstline Fisher Formenti Frontech Fujitsu Funai Furi Futuretech
Liesenk & Tter Local India TV Loewe Logik Longjiang Luxman LXI M&S M Electronic Magnavox Manesth Marantz Mark Matsui Matsushita Mediator Medion Megapower Megatron Meile Memorex Mercury Mermaid Metronic MGA Midland Minerva
Mitsubishi
Hitachi
Monivision MTC Mudan Multitech Myryad NAD Nanbao Nansheng National
Neckermann NEI Netsat Newave Nikkai Nikko Noblex Nokia Norcent Nordmende NTC Oceanic Onwa Optimus Orion Osaki Oso Otto Versand Palladium Palsonic Panama
RCA
Realistic Relisys Reoc Revox Rex Roadstar Rowa Runco Saba Sagem Saige Saisho Salora Sampo
Panasonic
Panda Pausa Penney
Samsung
Philco
Philips
Sanjian Sansei Sansui
Phonola Pilot Pioneer Polaroid Portland Prima Princeton Prism Profex Proscan
Transonic Tuntex TVS Universum Vector Research Vestel Victor Videocon Vidikron Viewsonic Viore Vizio Voxson Wards Warumaia Watson Waycon Weipai Westinghouse
7
VCR Codes
VCR
ABS Admiral Aiwa Akai Akiba Alba Alienware American High Amoisonic Anam Anam National Anitech Baird Basic Line Blaupunkt Brandt Brandt Electronique Broksonic Bush Canon CCE Cimline Citizen Colt Combitech Craig Crown Curtis Mathes CyberPower Daewoo Dansai Dell Dick Smith Electronics Digitor DirecTV DSE Dual Durabrand Elcatech Emerson Ferguson Firstline Fisher Fuji Funai Gateway GE Go Video
PVR
ABS Alienware CyberPower Dell DirecTV Gateway Hewlett Packard Howard Computers HP Hughes Network Systems Humax Hush iBUYPOWER JVC Linksys Media Center PC Microsoft Mind Niveus Media Northgate Panasonic Philips RCA ReplayTV Sonic Blue Sony Stack 9 Systemax Tagar Systems Tivo Toshiba Touch Viewsonic Voodoo ZT Group 1972 1972 1972 1972 0739 1972 1972 1972 1972
