Ring Sizing Guide
*Sizes & dimensions are approximate.
Make sure your printer is set to 100-percent. Do not reduce the print size in your printer ‘page setup’ area. You can verify that the ring sizer printed correctly by measuring it with a ruler; it should measure 3 1/2 inches long from "A" to "B". To open the print dialog box, press CTRL + P for pc or COMMAND +P for mac.
Method A: Measure Your Finger
*Sizes & dimensions are approximate.
Ring Sizing Guide
Method A: Measure Your Finger
Make sure your printersizer.to 100-percent. Do not reduce the print size in the print ‘page 1. Make sure your printer is set to 100 percent. Do not reduce your printer size in your page setup area (see dialog box below). Cut out the ring is set setup’ area. You can verify thatsure this page is printed at the correctwith a ruler; it should Use a quarter to make the ring sizer printed correctly by measuring it size. 2. Cut a3slit for Slot "A". "A" to "B". measure 1/2 inches long from 3.The printed quarter should finger where the ring an actual quarter placedthe numbers are facing out. Wrap the sizer around the be the same size as will be worn. Make sure on top of it. To open the print dialog box, press CTRL + P for pc or COMMAND +P for mac. 4. Pull the pointed end Tab "B" through Slot "A"until the sizer is snug. Make sure to allow size for your knuckle. If your To open the in between the press knuckle is sizeprint dialog box,two. CTRL+P for PC or COMMAND+P for Mac. 5. The number aligned with Slot "A" is your ring size. Use a quarter to 6. If the measurement lands between two numbers, your size is a half size. make sure this page Example: IfSample Dialog Box between 5 and 6, your ring size is 5 1/2. your measurement falls is printed at the correct size.
Use a quarter to make sure this page is printed at the correct size.
1. Cut out the ring sizer. finger at the beginning of the day to avoid incorrect measurements. More sizing mistakes are Sizing Tip: Measure your 2. Cut byslit for Slot "A". too large rather than too small. made a ordering rings 3. Wrap the sizer around the finger where the ring will be worn. Make sure the numbers are facing out. 4. Pull the pointed end Tab "B" through Slot "A"until the sizer is snug. Make sure to allow size for your knuckle. If your knuckle is size in between the two. 5. The number aligned with Slot "A" is your ring size. Read 6. If the measurement lands between two numbers, your size is a half size. Size Example: If your measurement falls between 5 and 6, your ring size is 5 1/2.
Here select actual size
A
B
Sizing Tip: Measure your finger at the beginning of the day to avoid incorrect measurements. More sizing mistakes are made by ordering rings too large rather than too small. 3½ Inches
Method B: Measure a Ring that Fits
Read Size Here
A
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
B
1. Select a ring that properly fits the intended finger. 3½ Inches 2. Place the ring on top of the circle below until the inside edge of the ring matches the outside of the circle. Comfort Fit Ring Tip: If the ring is a comfort fit design, match circles to the contoured edge of the inner surface of the ring.
Size 4.5 Size 6.5 Size 5.5 Size 6 Size Method 15.6 mm B: 5Measure a Ringmm 14.8 mm 16.9 mm 16 mm 16.45 that Fits
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Size 7 17.3 mm
Size 7.5 17.7 mm
Size 8 18.2 mm
1. Select a ring that properly fits the intended finger. 2. Place the ring on top of the circle below until the inside edge of the ring matches the outside of the circle.
21 mm Comfort Fit Ring Tip: If the ring is a comfort fit design, match circles to the contoured mm of the inner surface of the ring. 19 mm 19.4 mm 18.6 mm 20.6 edge 20.2 mm 19.9 mm Size 8.5 Size 9 Size 9.5 Size 10 Size 10.5 Size 11 Size 11.5
Size 4.5 14.8 mm Size 12 21.4 mm Size 8.5 18.6 mm
Size 5.5 Size 5 16 mm 15.6 mm Size 12.5 21.8 mm Size 9 19 mm
