...Design of Five Phase Induction Motor Sanket M. Bhimgade#1 Swapnil C. Chaudhari#2 Roshan B. Durge#3 Vabeihrohnei Chozah#4 Parag P. Salunke#5 Department of Electrical Engineering Dr. Babasaheb Ambedkar Technological University, Lonere, Raigad (MS - 402 103) sanketbhimgade@gmail.com , 2swapnil.28492@gmail.com , 3roshan.durge16@gmail.com , 4pawhrohnei@gmail.com , 1 Abstract: The conversion of electrical energy into mechanical energy has been and continuous to be a dominant form of power transmission for industrial purposes. The alternating current (AC) electric induction motor has been an industry workhouse for electromechanical conversion for over 100 years. This paper introduces the fundamental electric and mechanical principles of 5 phase AC induction motor. In this paper, a generalized formula is proposed for the selection of number of slots required for 5-phase alternative current (AC) machine design and the criterion for selecting the starting points of each phases. Keywords: Induction motor. Five phase, Stator winding. current. The power per phase is P = VP IP cosϕ and the total power is the sum of the amount of power in each phase. If the currents are equal and the phase angles are the same as in Fig. 1, then the load on the system is balanced, the current in the neutral is zero and the total power is [1], =3 cos ∅ Or Or = √3 = 1.73 cos ∅ cos ∅ I. INTRODUCTION In general, the induction machines having three-phase windings are...
Words: 3545 - Pages: 15
...A Novel Three-Phase to Five-Phase Transformation Using a Special Transformer Connection Atif Iqbal, Member, IEEE, Shaikh Moinuddin, Member, IEEE, M. Rizwan Khan, Sk. Moin Ahmed, Student Member, IEEE, and Haithem Abu-Rub, Senior Member, IEEE Abstract—The first five-phase induction motor drive system was proposed in the late 1970s for adjustable speed drive applications. Since then, a considerable research effort has been in place to develop commercially feasible multiphase drive systems. Since the three-phase supply is available from the grid, there is a need to develop a static phase transformation system to obtain a multiphase supply from the available three-phase supply. Thus, this paper proposes a novel transformer connection scheme to convert the threephase grid supply to a five-phase fixed voltage and fixed frequency supply. The proposed transformer connection outputs five phases and, thus, can be used in applications requiring a five-phase supply. Currently, the five-phase motor drive is a commercially viable solution. The five-phase transmission system can be investigated further as an efficient solution for bulk power transfer. The connection scheme is elaborated by using the simulation and experimental approach to prove the viability of the implementation. The geometry of the fabricated transformer is elaborated in this paper. Index Terms—Five phase, multiphase, three phase, transformer, turn ratio. I. INTRODUCTION ULTIPHASE (more than three phase) systems...
Words: 4370 - Pages: 18
...Linear Induction Motor 2 2.2 Double layer Winding 2.3 Electro-magnetic Bearings 6 3 Work Progress 9 4 Results References 1.0 INTRODUCTION The main idea behind this project is to understand the designing and operation of a Linear Levitating Machine and be able to create a successful prototype using the knowledge that we have acquired. Through this project we want to design and develop a machine which is capable of moving with the help of electromagnetic forces produced by the poles made by the stator windings and is lifted up due to the force generated by electromagnetic bearings. A single sided LIM (linear induction motor), with a short primary on the moving structure and a secondary of aluminium with back iron is being used in our project. An Electromagnetic Bearing is a bearing which is used to support a load without any physical contact. Since they are non-contact bearings, the friction losses are eliminated. Furthermore it avoids wear and tear which is normally associated with ball bearings. The operating speed is also improved. Since it is an active system, the bearings can control the levitation of the machine dynamically while it is in operation. 2.0 LITERATURE SURVEY 2.1 Linear Induction Motor – Linear Induction Motor is similar to a rotary poly phase induction motor where the air gap magnetic field in a poly phase LIM is a traveling magnetic field. The air gap field of an LIM, unlike that of a poly phase rotary induction motor...
Words: 2466 - Pages: 10
...Research Report 2005-27 Double Side Control of Wound Rotor Induction Machine for Wind Energy Application Employing Half Controlled Converters D. Panda, T. A. Lipo* Rockwell Automation Advanced Technology Lab, Richmond Heights, Ohio 44143, USA, dpanda@ieee. org *Department of Electrical and Computer Engineering University of Wisconsin, Madison, WI 53706, USA, lipo@engr.wisc.edu isconsin lectric achines & ower lectronics onsortium University of Wisconsin-Madison College of Engineering Wisconsin Power Electronics Research Center 2559D Engineering Hall 1415 Engineering Drive Madison WI 53706-1691 © 2005 Confidential Double side control of wound rotor induction machine for wind energy application employing half controlled converters Debiprasad Panda 1, Thomas .A.Lipo 2 Rockwell Automation Advanced Technology Lab, Richmond Heights, Ohio 44143, USA, dpanda@ieee.org 2 Department of Electrical and Computer Engineering University of Wisconsin, Madison, WI 53706, USA, lipo@engr.wisc.edu 1 Abstract – A double side converter fed wound rotor induction machine control for a wind energy application is proposed in this paper. In order to reduce the cost of a wind generator system, a new configuration using half controlled converters for both the stator and rotor circuit as well as for the line side is proposed. The proposed controller reduces the required KVA rating of both machine side and line side converters, improves the efficiency of the wind generator, helps operating...
Words: 5946 - Pages: 24
...INTRODUCTION This designation presents a universal picture of induction motors and their function in AC drive systems. Induction motors, specially those of the squirrel-cage type, are the most usual sources of mechanical force in the diligence. The main purpose that we use induction motors are they have a high power/weight ratio compared to DC motors and supplied from a three-phase AC line, induction motors are simple, full-bodied, and inexpensive, in contrast the main disadvantage is most motors operate with a fixed frequency resulting in an almost constant speed, adjustable-speed drives are increasingly introduced into a diversity of applications. Such a cause must include a power electronic converter to control the magnitude and frequency...
Words: 1395 - Pages: 6
...Induction Training at Delphi – TVS Introduction: Delphi TVS is a leading manufacturer of Fuel injection equipment and it is located in Sriperambudur, near Chennai. Being a manufacturer plant, they recruit people with engineer back ground and provide them with training as part of induction for a year. Fresh employees are tagged as “Graduate Engineer Trainee” and they need to successfully complete their one year induction program before getting promoted to “Engineer”. Now let us go through the complete structure of induction program that is practiced in this company Recruitment Procedure: Certain procedures followed by the company while recruiting people from Campus 1. Campus Selection: List of colleges are selected which is situated in various part of Tamil Nadu 2. Recruiting Team: HR Recruiting team, Technical Interview team (especially from R&D or Quality department) and HR Manager for HR Interview 3. Company Culture: Projecting TVS brand and Culture which is well established than brand Delphi Recruitment process has three stages: Written Test, Interview and Verification Below diagram explains the stages in detail Overview of Induction Program: Classroom Training phase of induction goes on for four months. It includes technical knowledge about the product (FIP), Practical learning of operating various machines to outdoor training like Swimming, Team building activity. Let us have a look at some of the important session that is provided to build both technical...
Words: 1341 - Pages: 6
...Arab Academy for Science, Technology and Maritime Transport College of Engineering and Technology Department: Electrical and Computer Control Engineering B. Sc. Final Year Project WIND ENERGY Presented By: Ahmed Magdy Ahmed Mokhtar Latifa Ahmed Supervised By: Dr.Amr Magdy DECLARATION I hereby certify that this material, which I now submit for assessment on the programme of study leading to the award of Bachelor of Science in (insert title of degree for which registered) is entirely my own work, that I have exercised reasonable care to ensure that the work is original, and does not to the best of my knowledge breach any law of copyright, and has not been taken from the work of others save and to the extent that such work has been cited and acknowledged within the text of my work. Signed: _____________________________ Registration No.: ___________ Date: 6/7/2013 2 ACKNOWLEDGMENT To my honourable Dr.AMR MAGDY We were honoured and pleased at the same time to work under the supervision of you, you spent a lot of time with us, at the time you definitely had lots of other important occupations. This work would have never been done without your assistance.Very thanking prof.Dr. Yasser Galal on his effort with us the past five years.Thanking engineers Noha Magdy and Ashraf Brdwyli to help us in the project. 3 ABSTRACT Wind energy is fast becoming the most preferable alternative to conventional sources of electric power. wind turbines...
Words: 13966 - Pages: 56
...mesh analysis, transient response of dc and ac networks; sinusoidal steady-state analysis, resonance, basic filter concepts; ideal current and voltage sources. The venin's, Norton's and Superposition and Maximum Power Transfer theorems, two-port networks, three phase circuits; Gauss Theorem, electric field and potential due to point, line, plane and spherical charge distributions; Ampere's and Biot-Savart's laws; inductance; dielectrics; capacitance. Signals and Systems: Representation of continuous and discrete-time signals; shifting and scaling operations; linear, time-invariant and causal systems. Fourier series representation of continuous periodic signals; sampling theorem; Fourier, Laplace and Z transforms. Electrical Machines: Single phase transformer - equivalent circuit, phasor diagram, tests, regulation and efficiency; three phase transformers - connections, parallel operation; auto-transformer; energy conversion principles. DC machines - types, windings, generator characteristics, armature reaction and commutation, starting and speed control of motors; three phase induction motors - principles, types, performance characteristics, starting and speed control; single phase induction motors; synchronous machines - performance, regulation and parallel operation of generators, motor starting, characteristics and applications; servo and stepper motors. Power Systems: Basic power generation concepts; transmission line models and performance; cable performance, insulation;...
Words: 875 - Pages: 4
...analyst operations, such as: ▪ Considation – aggregate of data, e.g. roll-ups from branches to regions. ▪ Drill-down – showing details, just the reverse of considation. ▪ Slicing and dicing – pivoting. Looking at the data from different viewpoints. E.g. X, Y, Z axis as salesman, Nth quarter and products, or region, Nth quarter and products. A Brief Overview Data Mining: Construct an advanced architecture for storing information in a multi-dimension data warehouse is just the first step to evolve from traditional DBMS. To realize the value of a data warehouse, it is necessary to extract the knowledge hidden within the warehouse. Unlike OLAP, which reveal patterns that are known in advance, Data Mining uses the machine learning techniques to find hidden relationships within data. So Data Mining is to ▪ Analyse data, ▪ Use software techniques ▪ Finding hidden and unexpected patterns and relationships in sets of data. Examples of Data Mining Applications: ▪ Identifying potential credit card customer groups ▪ Identifying buying patterns of customers. ▪ Predicting trends of market movement. Basic Structure of Data Mining tools Data Mining Techniques There are four main operations associated with data mining techniques: Predictive Modeling Database Segmentation Link Analysis Deviation Predictive...
Words: 1258 - Pages: 6
...with coils passing magnets at the same rate as the power supply frequency and resulting rotating magnetic field which drives it. Another way of saying this is that it does not rely on slip under usual operating conditions and as a result, produces torque at synchronous speed. Synchronous motors can be contrasted with an induction, which must slip in order to produce torque. They operate synchronously with line frequency. As with squirrel-cage induction motors, speed is determined by the number of pairs of poles and the line frequency. Synchronous motors are available in sub-fractional self-excited sizes to high-horsepower direct-current excited industrial sizes. In the fractional horsepower range, most synchronous motors are used where precise constant speed is required. In high-horsepower industrial sizes, the synchronous motor provides two important functions. First, it is a highly efficient means of converting ac energy to work. Second, it can operate at leading or unity power factor and thereby provide power-factor correction. The operation of a synchronous motor is simple to imagine. The armature winding, when excited by a poly-phase (usually 3-phase) supply, creates a rotating magnetic field inside the motor. The field winding, which acts as a permanent magnet, simply locks in with the rotating magnetic field and rotates along with it. During operation, as the field locks in with the rotating magnetic field, the motor is said to be in synchronization. Once the motor...
Words: 3243 - Pages: 13
...Method: There are three types of methods of filling with liquid filling machine which have the high rating of accuracy. These three methods are filling by volume, filling by time and filling by weight. For this filling machine, filling by volume method has selected in rigid plastic container as a mode of packaging to fill lubricant oil. The servo mechanism is used for the filling process which includes induction motor, encoder and high speed counter. The encoder produces the pulses by counting the rpm of the induction motor and gives its signal to the high speed counter and the high speed counter counts the pulses and compares it with the reference pulses and when the reference pulses and the counter pulses matched...
Words: 1429 - Pages: 6
...A Review of Induction Motors Pattinson Hayton California State University, Long Beach College of Engineering 12/03/2015 Thus far in Energy Conversion and Principles, the topics of direct current, or DC, and synchronous motors have been covered and discussed. A direct current exists in the field windings of both of these motors and an alternating current, or AC, exists in the armature windings of both of these motors. Electrical power is delivered right to the armature of a DC motor using a commutator, or the moving part of the rotary, in these motors. Because of this, a DC motor with this type of connection can also be referred to as a conduction motor. Conversely, if a motor receives power by induction, rather than by conduction, the motor is called an induction motor. An induction motor is therefore a type of transformer that possesses a rotary secondary winding. As discussed previously, both DC and synchronous motors are doubly-fed. An induction motor, however, is a singly-fed motor. With these motors being singly-fed, the construction of is different than that of other motors. These motors do not require slip-rings, a commutator, or brushes. With these components absent from induction motors, it is thus seen that there are no moving contacts between the stator and rotors, which is obviously quite different than the structure of DC and synchronous motors. Induction motors are useful due to their efficiency. The absence of brushes in induction motors eliminates...
Words: 3796 - Pages: 16
...Speed Control of Induction Motor using Fuzzy Logic Approach A PROJECT THESIS SUBMITTED IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF Bachelor of Technology In Electrical Engineering By Varuneet Varun (Roll 108EE011) G. Bhargavi (Roll 108EE026) Suneet Nayak (Roll 108EE044) Under Supervision of Prof. Kanungo Barada Mohanty Department of Electrical Engineering National Institute of Technology, Rourkela Rourkela- 769008, Odisha © 2011 - 2012 National Institute of Technology Rourkela Certificate This is to certify that the work contained in this thesis, titled “SPEED CONTROL OF INDUCTION MOTOR USING FUZZY LOGIC APPROACH” submitted by Varuneet Varun, G. Bhargavi and Suneet Nayak is an authentic work that has been carried out by them under my supervision and guidance in partial fulfillment for the requirement for the award of Bachelor of Technology Degree in Electrical Engineering at National Institute of Technology, Rourkela. To the best of my knowledge, the matter embodied in the thesis has not been submitted to any other University/ Institute for the award of any Degree or Diploma. Place: Rourkela Date: 11th May, 2012 Dr. Kanungo Barada Mohanty Associate Professor Department of Electrical Engineering National Institute of Technology Rourkela – 769008 i Acknowledgment We are grateful to The Department of Electrical Engineering for giving us the opportunity to carry out this project, which is an integral...
Words: 17434 - Pages: 70
...Chapter 1 Introduction 1.1 Background AC induction motors are being applied today to a wider range of applications requiring variable speed as they are the leading elements to convert electrical energy into mechanical energy. They are being used as actuators in various industrial processes, robotics, house hold appliances (generally single phase induction motor) and other similar applications. The reason for its day by day increasing popularity can be primarily attributed to its robust construction, simplicity in design and cost effectiveness. Also, induction motors are proved to be more reliable than DC motor. Generally, variable speed drives for induction motor requires wide operating range of speed and fast torque response, regardless of the load variations. Also, the conventional controllers have to linearize the non-linear system of induction motor in order to calculate the parameters, which is almost impossible to obtain a perfect non-linear model. Hence the values of the parameters that are obtained from it are thereby approximate. This leads us to more advanced control methods to meet the real demand. To overcome the complexities of conventional controllers, fuzzy logic controller have been implemented in many motor applications. A Fuzzy Logic Controller (FLC) is incorporated for combination with Phase Locked Loop (PLL) for precise and robust speed of induction motor. The fuzzy logic controller is used to pull the motor speed into the locking range of...
Words: 1757 - Pages: 8
...Abstract-This paper is based on the “Three phase motors protection” from various faults. This paper emphalis on various difficulties such as phase reversal in single and three phase systems, dropout of line, damage due to overload, failure of single phase there will be usually recommended to perform in complex environmental conditions. This includes in built cut-off frequency having several facilities together with timer in off condition and a starter which is automatic. This main circuit of this controllercompraises of a circuit with power supply, a latch and a counter which is used for phase sequence, timer of a motor with on and off conditions. There is a special provisions for checknhase sequence and is modified with decade counter and IC timer which simultaneously check the phase and allows the phase only if its frequency is 42Hz to 50 Hz. The dropping of line and overload which harms the motor is protected by next essential part. By using the objectives of a supply power, this controller controls the timer in on and off condition of a circuit motor and also the counter. The motor...
Words: 2844 - Pages: 12
