...Term Paper Course code :CSE 211 Course title: Computer Organisation and Architecture Submitted to: Ramanpreet Kaur Lamba Madam Submitted by: K. Nabachandra Singha Very-Long Instruction Word (VLIW) Computer Architecture ABSTRACT VLIW architectures are distinct from traditional RISC and CISC architectures implemented in current mass-market microprocessors. It is important to distinguish instruction-set architecture—the processor programming model—from implementation—the physical chip and its characteristics. VLIW microprocessors and superscalar implementations of traditional instruction sets share some characteristics—multiple execution units and the ability to execute multiple operations simultaneously. The techniques used to achieve high performance, however, are very different because the parallelism is explicit in VLIW instructions but must be discovered by hardware at run time by superscalar processors. VLIW implementations are simpler for very high performance. Just as RISC architectures permit simpler, cheaper high-performance implementations than do CISCs, VLIW architectures are simpler and cheaper than RISCs because of further hardware simplifications. VLIW architectures, however, require more compiler support. INTRODUCTION AND MOTIVATION Currently, in the mid 1990s, IC fabrication technology is advanced enough to allow unprecedented implementations of computer architectures on a single chip...
Words: 3947 - Pages: 16
...divides its functions in two categories, logical functions and processing functions. The arithmetic and logical unit and the control unit handle these functions respectively. The information is communicated through a bunch of wires called buses. The address bus carries the 'address' of the location with which communication is desired while the data bus carries the data that is being exchanged. Arithmetic & Logic Unit (ALU) This part of the central processing unit deals with operations such as addition, subtraction, and multiplication of integers and Boolean operations. It receives control signals from the control unit telling it to carry out these operations. Control Unit (CU) This controls the movement of instructions in and out of the processor, and also controls the operation of the ALU. It consists of a decoder, control logic circuits, and a clock to ensure everything happens at the correct...
Words: 1249 - Pages: 5
...COMPUTER ORGANIZATION AND ARCHITECTURE DESIGNING FOR PERFORMANCE EIGHTH EDITION William Stallings Prentice Hall Upper Saddle River, NJ 07458 Library of Congress Cataloging-in-Publication Data On File Vice President and Editorial Director: Marcia J. Horton Editor-in-Chief: Michael Hirsch Executive Editor: Tracy Dunkelberger Associate Editor: Melinda Haggerty Marketing Manager: Erin Davis Senior Managing Editor: Scott Disanno Production Editor: Rose Kernan Operations Specialist: Lisa McDowell Art Director: Kenny Beck Cover Design: Kristine Carney Director, Image Resource Center: Melinda Patelli Manager, Rights and Permissions: Zina Arabia Manager, Visual Research: Beth Brenzel Manager, Cover Visual Research & Permissions: Karen Sanatar Composition: Rakesh Poddar, Aptara®, Inc. Cover Image: Picturegarden /Image Bank /Getty Images, Inc. Copyright © 2010, 2006 by Pearson Education, Inc., Upper Saddle River, New Jersey, 07458. Pearson Prentice Hall. All rights reserved. Printed in the United States of America. This publication is protected by Copyright and permission should be obtained from the publisher prior to any prohibited reproduction, storage in a retrieval system, or transmission in any form or by any means, electronic, mechanical, photocopying, recording, or likewise. For information regarding permission(s), write to: Rights and Permissions Department. Pearson Prentice Hall™ is a trademark of Pearson Education, Inc. Pearson® is a registered trademark of...
Words: 239771 - Pages: 960
...NATIONAL INSTITUTE OF TECHNOLOGY SILCHAR Bachelor of Technology Programmes amï´>r¶ JH$s g§ñWmZ, m¡Úmo{ à VO o pñ Vw dZ m dY r V ‘ ñ Syllabi and Regulations for Undergraduate PROGRAMME OF STUDY (wef 2012 entry batch) Ma {gb Course Structure for B.Tech (4years, 8 Semester Course) Civil Engineering ( to be applicable from 2012 entry batch onwards) Course No CH-1101 /PH-1101 EE-1101 MA-1101 CE-1101 HS-1101 CH-1111 /PH-1111 ME-1111 Course Name Semester-1 Chemistry/Physics Basic Electrical Engineering Mathematics-I Engineering Graphics Communication Skills Chemistry/Physics Laboratory Workshop Physical Training-I NCC/NSO/NSS L 3 3 3 1 3 0 0 0 0 13 T 1 0 1 0 0 0 0 0 0 2 1 1 1 1 0 0 0 0 4 1 1 0 0 0 0 0 0 2 0 0 0 0 P 0 0 0 3 0 2 3 2 2 8 0 0 0 0 0 2 2 2 2 0 0 0 0 0 2 2 2 6 0 0 8 2 C 8 6 8 5 6 2 3 0 0 38 8 8 8 8 6 2 0 0 40 8 8 6 6 6 2 2 2 40 6 6 8 2 Course No EC-1101 CS-1101 MA-1102 ME-1101 PH-1101/ CH-1101 CS-1111 EE-1111 PH-1111/ CH-1111 Course Name Semester-2 Basic Electronics Introduction to Computing Mathematics-II Engineering Mechanics Physics/Chemistry Computing Laboratory Electrical Science Laboratory Physics/Chemistry Laboratory Physical Training –II NCC/NSO/NSS Semester-4 Structural Analysis-I Hydraulics Environmental Engg-I Structural Design-I Managerial Economics Engg. Geology Laboratory Hydraulics Laboratory Physical Training-IV NCC/NSO/NSS Semester-6 Structural Design-II Structural Analysis-III Foundation Engineering Transportation Engineering-II Hydrology &Flood...
Words: 126345 - Pages: 506
...*3963103* [3963] – 103 T.E. (Petroleum) (Semester – I) Examination, 2011 DRILLING & PRODUCTION OPERATIONS (2003 Course) Time : 3 Hours Max. Marks : 100 Instructions : 1) Question Nos. 1 and 5 are compulsory. Out of the remaining attempt 2 questions from Section I and 2 questions from Section II. 2) Answers to the two Sections should be written in separate books. 3) Neat diagrams must be drawn wherever necessary. 4) Black figures to the right indicate full marks. 5) Use of Logarithmic Tables, Slide Rule, Mollier Charts, Electronic Pocket Calculator and Steam Tables is allowed. 6) Assume suitable data, if necessary. SECTION – I 1. What are different systems on a drilling rig ? Explain any one in detail with suitable diagramme. 18 2. a) Calculate Bottom hole pressure if well depth is 2500 m and mud weight is 1.2 gm/cc. b) Calculate mud weight if mud gradient is 0.87 psi/ft. ′ c) Calculate volume bbl/meter for drill pipe O.D. = 5′ inch and I.D. = 4.276 inch. 2 2 2 10 8 8 16 d) Draw circulation system on a drilling rig. 3. a) Discuss IADC classification of a bit in details. b) Discuss different factors affecting rate of penetration in details. 4. Write short note on : i) Coring ii) Fishing tools iii) BOP iv) Directional well P.T.O. [3963] – 103 -2- *3963103* SECTION – II 5. a) Discuss different types of casings and function of the casings in brief. b) Discuss different types of well completion techniques. 6. a) Discuss primary cementation process with...
Words: 172166 - Pages: 689