Unit 17 Gas turbine science outcome 2 assignment 2 Q1 4) Cross reference to Unit 17 Gas turbine science outcome 2 assignment 1 Q1 Outcome 3.2 Materials used in gas turbines have gone through many incremental improvements since the first practical turbines were developed in the 1940s. Most recent efforts have led to improved steel alloys for use in turbine vanes, blades, and inlet blocks. material improvements have led to an increase in rotor life and reliability. Progress in gas turbine
Words: 2787 - Pages: 12
and Produce Thrust Table of Contents 1.0 Introduction 3 2.0 Basic Components of a Jet Engine 4 2.2 Compressor 4 2.3 Combustor 5 2.4 Turbine 5 2.5 Exhaust Duct/Nozzle 5 4.0 Creation of Thrust in a Turbojet Engine 7 5.0 Conclusion 9 6.0 References 10 1.0 Introduction According to Hunecke (1997), jet engines, also known as gas turbine engines, are the most widespread and most efficient method used for airplane propulsion currently. The Jet engine uses basic principles and concepts
Words: 1759 - Pages: 8
FUNDAMENTALS OF GAS TURBINE ENGINES INTRODUCTION The gas turbine is an internal combustion engine that uses air as the working fluid. The engine extracts chemical energy from fuel and converts it to mechanical energy using the gaseous energy of the working fluid (air) to drive the engine and propeller, which, in turn, propel the airplane. THE GAS TURBINE CYCLE The basic principle of the airplane turbine engine is identical to any and all engines that extract energy from chemical fuel. The basic
Words: 4458 - Pages: 18
Needs Analysis Training and Development HR 592 Introduction The purpose of the survey is to give the employee the opportunity to provide opinions on where Solar Turbines Inc. should focus their attention in order to improve the climate and productivity of the Test Department. The survey was complete and analyzed, the results will be used to improve in areas of training and development. The results of the assessment was analyzed by our human resource department, the two student from
Words: 651 - Pages: 3
Natural gas is a vital component of the world’s supply of energy. It is one of the cleanest, safest, and most useful of all energy sources. Natural gas is a fossil fuel. Like oil and coal, this means that it is, essentially, the remains of plants and animals and microorganisms that lived millions and millions of years ago. In the 19th and early 20th centuries, natural gas was used primarily for street and building lighting, providing what was known as gaslight. Today, improved distribution of
Words: 463 - Pages: 2
DIFFERENT TYPES OF AIRCRAFT ENGINE AIR INLET Air intake (inlet) — For subsonic aircraft, the inlet is a duct which is required to ensure smooth airflow into the engine despite air approaching the inlet from directions other than straight ahead. This occurs on the ground from cross winds and in flight with aircraft pitch and yaw motions. The duct length is minimized to reduce drag and weight.[1] Air enters the compressor at about half the speed of sound so at flight speeds lower than this the
Words: 2391 - Pages: 10
INDUSTRIAL TRAINING REPORT AT KAPAR ENERGY VENTURES SDN.BHD KAPAR, SELANGOR BY CHOLAN A/L VENU (ME090139) DEPARTMENT OF MECHANICAL ENGINEERING UNIVERSITI TENAGA NASIONAL START DATE :09/03/15 END DATE :29/05/15 ABSTRACT As a third year degree student in Bachelor of Mechanical Engineering (Hons.), I have been assigned to undergo industrial training for 12 weeks. This industrial training is one of the vital part of my coursework whereby I will be able to graduate from
Words: 6281 - Pages: 26
I personally feel that there is substantial respect to be gained by pursuing the field of Mechanical Engineering. The diversity present in this field has attracted me and it is consistent with my enthusiasm for Mathematics and Science. It has a lot of scope as well. I have gone through the entire course and the specific areas, which interested me, were Robotics and Project Design. I know what a career in Engineering is like, since I have done an internship as a Engineer in MTA. I have been quite
Words: 633 - Pages: 3
ACKNOWLEDGEMENT We would like to acknowledge and extend our heartfelt gratitude to the intelligence and co-operation of those people who had been so easy to let us understand what we needed from time to time for completion of this report. We want to express our special gratitude towards Ma’am Rafia Ayub of Cost Accounting, for giving us such a unique project. CHAPTER O5: CLASSIFICATION OF COST Cost can be classified into two categories i.e. product cost and period cost.
Words: 1596 - Pages: 7
with an engine in the space shuttle. The engine which has high capability and which has high working performance can be known as high engine capability. However, Engine is not a single component but is embedded with many other components like the turbine blades. This whole combined package and how high these components can work is called as high engine capability. As it is in the case of space shuttle it is expressed as an engine but when it comes to software engineering and testing terms the engine
Words: 719 - Pages: 3
