Name: Suzzanna Stevens Exercise 5: Cardiovascular Dynamics: Activity 1: Studying the Effect of Blood Vessel Radius on Blood Flow Rate Lab Report Pre-lab Quiz Results You scored 100% by answering 5 out of 5 questions correctly. 1. Blood flow is measured in You correctly answered: b. ml/min. 2. Which of the following has the greatest effect on blood flow? You correctly answered: a. blood vessel radius 3. Which of the following would not result in a decrease in the blood vessel radius? You
Words: 603 - Pages: 3
Quiz 6 1) (a) Figure 1 below shows the arrangements of a circuit for a hydraulic system. The pump draws oil with a specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 125 mm, and in 15 s the piston must travel 500 mm while exerting a force of 5000 kg. It is estimated that there are energy losses of 3.5 m in the suction pipe and 10.7m in the discharge pipe. Both pipe diameter is 50mm. Calculate: (i) The volume flow rate
Words: 269 - Pages: 2
1. The work in this report was written collectively by the members of this group and reflects the laboratory and analysis efforts primarily of this group. 2. The data and other findings of the report are entirely those of this group. 3. The group may have discussed experimental problems during the laboratory with members of other groups or with the TA and may have consulted with members of other groups: where such discussions had significant impact on our work, we have noted the
Words: 3231 - Pages: 13
The objectives of this experiment are to investigate the way in which the static pressure varies on the surface of an aerofoil in low speed flow, and to deduce the lift force acting on the aerofoil. An aerofoil with a symmetrical section is used for the experiment, which is conducted in a wind tunnel at a wind speed low enough for the flow to be treated as incompressible. From the measured distribution of surface pressure around the aerofoil at a small angle of incidence, the lift will be calculated
Words: 406 - Pages: 2
Scheme-G Sample Test Paper- I Course Name :- Diploma in Electronics Engineering Group Course Code :- EJ/EX/ET/EN/IS/IC/IE/IU/ED/EI Semester :-Fourth 17434 Subject Title :- Industrial Measurements Marks :-25 Time:-1 hour Instructions: 1. All questions are compulsory. 2. Illustrate your answers with neat sketches wherever necessary. 3. Figures to the right indicate full marks. 4. Assume suitable data if necessary. 5. Preferably, write the answers in sequential order. Q1. Attempt any THREE of
Words: 1264 - Pages: 6
ABSTRACT Pumps are an essential part of any system where the movement of fluids is needed. In this experiment, pump curves, pumps in parallel and series as well as the phenomenon of cavitation were investigated. The objectives for the experiment were: to determine a characteristic pump curve of a single centrifugal pump and compare it to the manufacturer’s pump curve; to confirm that the overall pump curve for pumps in series and parallel can be obtained from the individual pump curves and finally
Words: 3410 - Pages: 14
PIC 18F4520 is 40 pin IC which performs the controlling action. That is the water flow is sensed and given to controller. The controller will take the action according to the given condition. Water flow sensor is used to sense the water have been passed through it. If the one litre is passed through the sensor it will give 450 pulse. Keypad is used if the extra water is needed. If we need 10 litre extra the we can type 10
Words: 813 - Pages: 4
7 VanePump PVR1T-8-FRA-28 Yuken 1 8 Electricmotor 3hp x1440rpm;50Hz Foot Mounting Monark/ CGL 1 The hydraulic circuit of the system is shown in figure 2. Figure 2: Circuit Diagram of Hydraulic system 4. Mathematical Modeling of the Components 4.1 Modeling of Valves and Actuators The input to the system is the movement of the valve xi. This allows the flow of oil into the cylinder of Q m3\s which makes the cylinder move a distance xo [6]. Assuming constant supply pressure the flow rate is directly
Words: 750 - Pages: 3
UNIVERSITY OF SUNDERLAND / SEGi UNIVERSITY BA (HONS) BUSINESS & MANAGEMENT Module: Core Business Skills Code: UGB 103 Assessment Element 1: Skills Audit and PDP Plan (Total 15 module marks) (This assignment covers the following skills learning outcomes, taken from the Module Guide: Skills:- 8 - Manage own time, including setting own goals and targets for Progress Files) Date of Submission: 12th October 2012 TASK: Draw up an initial skills assessment to rate your skills
Words: 2037 - Pages: 9
The Condition | True or False | attAverage >= verizonAverage | True | tmobileAverarge == 868 | True | verizonAverarge < spirntAverage | False | sprintAverage != attAverage | True | The condition | Expected Ouput | If tmobileAverage > 800 and VerizonAverage > 800 ThenDisplay “Both have average download rates over 800”ElseDisplay “One or both of the averages are less”End If | Both have average download rates over 800 | If sprintAverage == 800 ThenDisplay “Sprint download
Words: 268 - Pages: 2
