| BRANCH: M. Tech. Design ROLL NO. : -121424016 TRAINING AND PLACEMENT CELL COLLEGE OF ENGINEERING, PUNE RESUME YEAR: 2015-2016 I) PERSONAL 1) Full Name: KASHID ANURAG ASARAM (SURNAME NAME FATHER’S NAME) 2) Present Address: -: Rahi Apartment Flat no. 9. 365, Ganjwe chowk, Navi Peth
Words: 319 - Pages: 2
PART B - THE IMPLEMENTATION Procedures: 1. The circuit was set up as depicted in the schematic diagram shown 2. One end of the 3Ω-5W resistor was connected to the positive terminal of dc power supply. 3. The other end of the resistor was connected to the red testing probe of the ammeter. 4. Using another connecting wire, the black testing probe of the ammeter was connected to the switch feed of the single pole switch. 5. The other terminal of the single pole switch was connected
Words: 658 - Pages: 3
Case 13-6 Natural Irony: Accounting Considerations When There Is a Natural Disaster WetWind Alternatives Corp. (“WWA”) is a publicly traded company in Reedsport, OR, that produces electricity using alternative production methods; specifically, using wind and wave-powered turbines. WWA operates one of the first commercial wave-power farms installed in the United States off the coast of Oregon near the mouth of Umpqua River. The wave-powered farm provides power to the city of Reedsport using turbines
Words: 849 - Pages: 4
Covering Page: CDGI’S CHAMELI DEVI SCHOOL OF ENGINEERING (CDSE), INDORE ULTRABOOK by MAYANK YADUWANSHI (0832CS141084) Mr. DHARMENDRA GUPTA (FACULTY) DEPARTMENT OF COMPUTER SCIENCE ENGINEERING 2015 – 2016 November 2015.
Words: 653 - Pages: 3
But before electricity could be consumed to power a load or a certain device, it needs to travel long distances through the utilization of electrical power systems. Electrical Power Systems consists of mainly of generating stations, transmission lines and distribution systems. From the generating stations, different types of energy are converted to electrical energy (high voltage) and then transported to the distribution systems through the transmission lines, where the voltages to be delivered to
Words: 1876 - Pages: 8
Our analysis showed a near linear relationship between current and voltage for the resistor, as expected. Our experimental error for the factory versus actual resistance was only 4.77%. The resistance of the light bulb is not as linear as with the resistor. This is because the resistance changes when the light come on, as some of the energy is converted to heat in the filament. The critical point when the light first turns on is at O.456 Volts and you can see on the graph that the resistance begins
Words: 420 - Pages: 2
motors can be used in situations where constant speed drive is required. Chapter IV EPM1076 3 Chapter IV EPM1076 4 Angle in Electrical and Mechanical Unit -For 2 pole machine, when the rotor rotates for one revolution, the induce emf varies for one cycle. i.e. θ = θm, (refer to figure 2) -Where θ is the angle in electrical degrees or radians and θm is the mechanical angle. - For a 4 pole machine, as the rotor rotates for one revolution (θm = 2π), the induced emf varies
Words: 2662 - Pages: 11
Jennifer L. Theresa Scott ENC 1101: Comp 1 June 8th, 2016 The Machines of Tomorrow Technology is everywhere. You go out in public and all you see is everyone concentrating on their phones. Technology allows people to communicate with one another and share information. Even if someone doesn’t own a computer or a phone, there is some type of mobile device, computer, or even television that you can get too to get the latest news. I was born in 1999, where technology wasn’t as big as it is now
Words: 825 - Pages: 4
you are installing cable in conduits within a structure, be sure that you have allowed enough room for the cable or cables you are installing. Tray and duct installation is used inside structures and is similar to installation methods used for electrical wiring. Because many optical fiber cables are nonconductive, some of the requirements and restrictions for copper do not apply to fiber. When the optical fiber rests in trays or horizontal ductwork the weight of the cable is usually not a factor
Words: 255 - Pages: 2
Name LC – Lab 20 Go to http://phet.colorado.edu/en/simulation/circuit-construction-kit-ac and click on Run Now. Arrange the circuit according the diagram below: You may have to replace the red and black voltmeter connections to the proper location in the circuit. a. Charge the capacitor by closing the switch on the left. Sketch the graphs of Voltage vs. Time for the resistor and the capacitor below. b. What happens to the
Words: 604 - Pages: 3
