server is 172.30.0.8. The allocated source IP host address for the LAN Switch 1 server is 172.16.8.5. The allocated source IP host address for the LAN Switch 2 server is 172.16.20.5. The allocated source IP host address for the IP default gateway router is 172.30.0.1. 3. The targeted IP hosts did respond to the ICMP echo-request packet with an ICMP echo-reply packet when I intiated the ping command and four packets were sent back to the IP source. 4. The command line syntax for running an
Words: 340 - Pages: 2
identification number of the particular packet, the protocol, packet length and synchronization. Packets are typically routed from source to destination using network switches and routers. Each packet contains address information that identifies the sending computer and intended recipient. Using these addresses, network switches and routers determine how best to transfer the packet to its destination Pros and Cons of Packet Switching Packet switching is the alternative to circuit switching protocols used
Words: 307 - Pages: 2
service uses a fiber optic line sometimes copper, it carries 24 digitized voice channels or data at a rate of 1.544 MBPS. It plugs into the phone system if its only being used for voice calls, if data is being used then it plugs into the network’s router. By moving from high-end T1 services to DSL/Cable access services, Riordan monthly network communications cost will be reduced. With download availability up to 18Mbps per circuit, you could move Active Directory, Exchange services, file sharing,
Words: 355 - Pages: 2
obtained. But using Heuristic technique the results are not always optimal and may have some limitations. To overcome all this we can use decomposition method which is very efficient for computation and results are nearly exact. Introduction- Routers are basically classified into two types- Oblivious and Adaptive. In oblivious routing the path is completely determined by the sources and destination. Whereas Deterministic routing is the same path is chosen between a source and destination. The
Words: 1064 - Pages: 5
Note: The routers used CCNA labs are Cisco 2911 Cable the network as shown in the topology. Attach the devices as shown in the topology diagram, and cable as necessary. Configure PC hosts. Initialize and reload the routers and switches as necessary. Configure basic settings for each router. Configure routing. Configure OSPF on the routers in area 1 with process ID of 100, in area 0 with process ID of 110, in area 2 with 200. R6(config)#router ospf 100 R6(config-router)#network 8
Words: 1093 - Pages: 5
news site, or it may mean that someone is up to no good. A sudden jump in the number of bad or malformed packets. Some routers collect packet-level statistics; you can also use a software network scanner to track them. Some routers collect packet-level statistics; you can also use a software network scanner to track them. Also large numbers of packets caught by your router or firewall's egress filters. Egress filters prevent spoofed packets from leaving your network, so if your filter is catching
Words: 524 - Pages: 3
Task 1—Verify Connectivity and Configuration in Dallas router #1. What CLI command does produce the output below? ------------------------------------------------- ------------------------------------------------- ------------------------------------------------- ------------------------------------------------- #2. Complete the table below based on the dynamic routes displayed in the routing table above. Routing protocol | Destination Network | Metric | Outbound Interface
Words: 329 - Pages: 2
learned how to Configuring OSPF setting in a router simulated environment. We learned the commands that must be used to properly install these settings. We learned how to create a designated router and a backup router and how to see which ones are directly connected to the main router. As well as how to change those designated and backup routers ID and addresses. Along with a few other commands that show you the routing tables and the neighboring routers connected. This will help me greatly in the
Words: 506 - Pages: 3
Configuration Guide OSPF internal route 10 OSPF export IS-IS Level 1 internal route 15 IS-IS external-preference, preference IS-IS Level 2 internal route 18 IS-IS external-preference, preference Default 20 - Redirects 30 - Kernel 40 - SNMP 50 - Router Discovery 55 - RIP 100 RIP preference RIPng 100 RIP preference PIM 105 JUNOS
Words: 365 - Pages: 2
ITU Which of the following are true about a router? (Choose three) A. Routers enable different IP networks or IP subnets to communicate with each other. C. Path selection is one of the main functions of a router E. Routers have a central processing unit and memory. Which of the following are main components of a router? (Choose three) A. ROM B. Flash memory E. RAM Which of the following statements describe the function of RAM in a router? (Choose two) C. RAM stores the current configuration
Words: 456 - Pages: 2
