Routers Term Paper INTRODUCTION Router is a hardware device designed to take incoming packets, analyzing the packets and then directing them to the appropriate locations, moving the packets to another network, converting the packets to be moved across a different network interface, dropping the packets, or performing any other number of other actions. In the picture to the down, is a Linksys BEFSR11 router and is what most home routers
Words: 569 - Pages: 3
switches provides high bandwidth between all layers and great redundancy in this level. Distribution layer: The routers are using as a routing protocol EIGRIP. Access layer: This layer connects the users with the routers through 4 switches and 40 wireless access points. Users: Here are approximately 700 people connected to the network with up to 1.500 devices mostly using wireless. Internet edge: A 2 Gbit external fiber connection is available and a firewall
Words: 1684 - Pages: 7
point between network equipment and the ports to which the PCs are connected. Router x1 – This is where the default gateway for the network will be and is located at the demarcation point. It is used to route information obtained by the network and deliver packets returned by the Internet. Wireless Access Point x1 – The WAP will be located in the Library and is used to grant wireless access to the internet via the router to those who need it. select the appropriate network connecting devices to use
Words: 407 - Pages: 2
Network interface card: - it is the basic component which allows the computer to communicate across the network. Now day it built up with motherboard. It can be separate card for the use in slots or external units. Network can be operating on wire, wireless or both of them. NCI acts as physical interface between the computer and network cables. On a local area network (LAN) typically contain a network interface card specifically designed for the LAN transmission technology. The specification of
Words: 565 - Pages: 3
Wireless Router Configuration- Gateway Configuration Cisco Linksys Products (http://homesupport.cisco.com/en-us/wireless/lbc/WRT54G) Model # WRT54G Firmware : v1.4 – v 4.20. Barry Rodricks Outline Introduction. Configuring the Router as a Gateway. References Introduction What is a default Gateway ? A default gateway is the device that passes traffic from the local subnet to devices on other subnets. The default gateway often connects a local network to the Internet, although
Words: 304 - Pages: 2
example, there a two networks. The first one the device are connected by wireless technology and other by cables. The device which using wireless only can communicate with other wireless and the wired device only can communicate with wired also. So, all device can communicate with each other using a network bridge. It also determines a data packet are allowed or not to the other part of the Ethernet segments. Router Router is a device that allows the similar network to interchanges data packets between
Words: 777 - Pages: 4
Top-Down Network Design Third Edition Priscilla Oppenheimer Priscilla Oppenheimer Cisco Press 800 East 96th Street Indianapolis, IN 46240 ii Top-Down Network Design Top-Down Network Design, Third Edition Priscilla Oppenheimer Copyright© 2011 Cisco Systems, Inc. Published by: Cisco Press 800 East 96th Street Indianapolis, IN 46240 USA All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying
Words: 79785 - Pages: 320
will identify the system it is in. Once you establish your LAN, then you can move on to connect with other LANs which will form a WAN or MAN, not only through the NIC Adapter but other network devices mentioned below. This is where a Router comes into play. A router is an intelligent network device which transmits data to other destined computers. It connects two networks and like I said, it forwards packets between them according to the information in the packet header. This communication occurs
Words: 607 - Pages: 3
COMPUTER NETWORKING LAB Mahantesh Patil 2BV14IS410 Mahantesh Patil 2BV14IS410 CN LAB REPORT Dept. of ISE, BVBCET LAB-01 List the hardware components 1) Difference between switch and Hub: 2) Difference between SWITCH and ROUTER 3) Differences between Router and Gateway 4) What is the Difference between Subnetting and Supernetting? HARDWARE COMPONENTS Cables: 1|Page Mahantesh Patil 2BV14IS410 CN LAB REPORT Dept. of ISE, BVBCET Cables: which are used to connect one
Words: 3647 - Pages: 15
and ensure optimal schedule definition. Development stage – initial development Function of routers The routers in the network provide a gateway between the networks. Router 1 will provide a gateway to the Internet, Router 2 will provide a gateway between the workgroup networks; file server web server and the Isolation LAN, which will connect the administration network and the isolation LAN. The routers will select the best path using a metric which can be calculated on Hop count, bandwidth, delay
Words: 1581 - Pages: 7
