Table of Contents Assignment: 2 1 Introduction 1 1) You need to select an Op Amp circuit of your choice (inverting, non-inverting, summing, comparator, feedback, voltage regulator, etc.). Simulate the circuit in any of the packages you have identified in the first assignment, and then assess the performance of the software package by carrying out mathematical analysis of the circuit. 2 Op Amp Summing Amplifier 2 Op Amp Summing Amplifier Simulation 1 2 Op Amp Summing Amplifier Simulation
Words: 2165 - Pages: 9
Other remote control systems General Description The 212 encoders are a series of CMOS LSIs for remote control system applications. They are capable of encoding information which consists of N address bits and 12-N data bits. Each address/data input can be set to one of the two logic states. The programmed addresses/data are transmitted together with the header bits via an RF or an infrared transmission medium upon receipt of a trigger signal. The capability to select a TE trigger on the HT12E
Words: 3546 - Pages: 15
Electrical Engineering 101 Third Edition Electrical Engineering 101 Everything You Should Have Learned in School… but Probably Didn’t Third Edition Darren Ashby AMSTERDAM • BOSTON • HEIDELBERG • LONDON NEW YORK • OXFORD • PARIS • SAN DIEGO SAN FRANCISCO • SINGAPORE • SYDNEY • TOKYO Newnes is an imprint of Elsevier Newnes is an imprint of Elsevier 225 Wyman Street, Waltham, MA 02451, USA The Boulevard, Langford Lane, Kidlington, Oxford, OX5 1GB, UK © 2012 Elsevier Inc. All rights
Words: 111107 - Pages: 445
This part of the reading will examine the CPU, Buses, Controllers, and Main Memory. Other sections will examine input devices, output devices, and secondary memory. The Central Processing Unit (CPU) Figure 2: The Central Processing Unit The computer does its primary work in a part of the machine we cannot see, a control center that converts data input to information output. This control center, called the central processing unit (CPU), is a highly complex, extensive set of electronic circuitry
Words: 2592 - Pages: 11
instructions (a program). A computer system includes a computer, peripheral devices, and software Capabilities of Computers Speed: computer operates on data and commands at incredibly fast speed. Storage: computer can store enormous amount of data and information in its memory. Reliability: computers made of modern technology rarely breakdown and when they do, they are easily repaired. Consistent: if you input the same data into the computer using the same program, it will give you the
Words: 1177 - Pages: 5
Week 4 Assignment 1: Computer Architecture Tony D. Everett Professor Jennifer Merritt CIS106 Intro to Information Technology July 28, 2013 Introduction The use of Information Technology is well recognized. Information Technology has become a must for survival of all business housing with the growing IT trends. The computer is the main component of any Information Technology system. Today, computer technology has filled every scope of existence of modern man. From airline reservations to
Words: 1237 - Pages: 5
applications. Almost all the real world and real time systems built around microcontrollers and microprocessors make use of interrupts. What is an Interrupt The interrupts refer to a notification, communicated to the controller, by a hardware device or software, on receipt of which controller momentarily stops and responds to the interrupt. Whenever an interrupt occurs the controller completes the execution of the current instruction and starts the execution of an Interrupt Service Routine (ISR)
Words: 795 - Pages: 4
between the SLC 500 series and the newer Logix series of PLCs? 3. What is the difference between rack/slot-based memory organization and a tag-based memory system? In rack/slot-based memory, the programmer assigns the data from an input field device to an input instruction on a ladder rung by specifying the memory location but for the tag based memory the allocation of variable names for program values is not tied to specific memory locations in the memory structure. 4. What is the difference
Words: 399 - Pages: 2
Jaipur Engineering College & Research Centre, Jaipur Manual Of TCP/IP Programming Lab (7CP8) Session 2007-2008 Computer Engineering Department Prepared By: Mahesh Jangid cc Exercise No. 1 AIM: Study of Data Communication System, Connectionless and connection oriented service, programming with TCP and UDP. Theory: - [pic] Networking Basics • computers running on the Internet communicate to each other using either Transmission
Words: 2326 - Pages: 10
disk drivers, display screens, keyboards printers, boards, and chips. In contrast, software is untouchable. The typical components of a computer consist of the central processing unit (CPU), main memory, secondary storage devices, input devices, and output devices. The CPU runs the program. While the computer is running it is stored in the main memory. Commonly known as the random access memory (RAM). Secondary storage is all data storage that is not currently in a
Words: 778 - Pages: 4
