punch and die surfaces. Due to that, the sheet metal will deformed into the desired shape. Some of the most common outcomes in deep drawing process are tearing and wrinkling or the formation of uneven height at the top rim of a drawn part due to the material anisotropy. Wrinkling as become a serious obstacle to forming quality and part functions and finally results in scraps. This defects are caused due to change in parameters like
Words: 1177 - Pages: 5
surface. Aerogels as a whole are made by creating a gel then extracting the solvent with supercritical fluid extraction. This leaves a very porous, low-density solid. Due to their porous nature, aerogels are considered to be the finest insulation materials available. Silica aerogels are good insulators, but will flake apart and produce dust in the Mars atmosphere. For this reason, all-polymer aerogels should be used over their silica-based counterparts. They can be created as thin, flexible films and
Words: 744 - Pages: 3
ACKNOWLEGDEMENT The successful completion of this study would not have been possible without the assistance and cooperation of a number of persons. Members of my family especially my mother and Mr. James, they have been a constant source of encouragement and assistance. Finally, special thanks to my teacher Mr. James who has guided me every step of the way throughout this exercise. DESCRIPTION OF THE BUSINESS JAMAICAN TINGS “PREPARING AND DELIVERING DELICIOUS MEALS TO YOUR DOOR”
Words: 2204 - Pages: 9
3. Materials This section will describe the materials that were used in the laboratory experiments that will be presented in this thesis. 3.1 Portland CEMENT Portland cement is composed of a combination of limestone and either shale, clay, sand, or iron. These materials are ground and blended together and heated in a kiln from 2600o F to3000o F. This causes the materials to fuse together to create clinker. Cooled clinker is then ground with gypsum (CaSO4*2H20). The addition of gypsum controls the
Words: 1043 - Pages: 5
attempted by this unique process. Friction Stir Welding can be used to join aluminum sheets and plates without filler wire or shielding gas. Material thicknesses ranging from 0.5 to 60 mm can be welded from one side at full penetration, without porosity or internal voids. Nowadays welding materials is chosen for non-ferrous materials and it has a broad range of materials. In this paper we have identified the effects of different process parameters on friction stir welding of aluminium 1100 and aluminium
Words: 1526 - Pages: 7
MANUFACTURING CHALLENGES AND REMEDIES OF NANO SiC PARTICULATES FROM QUARTS BY MECHANICAL ABERRATION METHOD R. Selvam1, S. Ravi2, 1 Research scholar, Department of Mechanical Engineering, Bharath University, Chennai, India. 2 Professor, Department of Mechanical Engineering, Sriram College of Engineering, Chennai, India. Abstract Among the various non-oxide ceramics, silicon carbide (SiC) is the leader. The attractive properties, such as good specific strength and Young’s modulus as a function
Words: 1353 - Pages: 6
Relationship between Kmax and σf Kannan et al. [23] had examined the applicability of a modified two-parameter fracture criterion MTPFC which introduced by Christopher et al. [24, 25] while assessing the fracture strength of structure components. They utilized a relation between the stress intensity factor (Kmax) and the corresponding stress at failure (σf) as (2) where σf is the hoop stress at the failure pressure
Words: 832 - Pages: 4
disc can also be used as well. In this application, the film will be more uniform and we will be able to save 10 to 15 percent of the material because there will be a reduction in the overspray. There are many low prices units available. A high voltage electrostatic charge is applied to the workpieve and the sprayer mechanism. Both powdered and liquid paint materials can be used The overpack is first sprayed with or dipped with paint particles which are
Words: 475 - Pages: 2
Drinkin’ with Dad My family likes to drink. In fact, looking back on my life, it is really what we did together the most. It seemed like it was the one thing we were best at and proud of. My Dad used to own a bar. I began working at my Dad’s bar when I was still in school. I would walk to the bar after football practice work at the bar. On weekends I would work one night in the back. My brother John worked there too and my brother Brian got sent away. One
Words: 287 - Pages: 2
strain response of two different materials were measured as stress was applied to them. The materials were an aluminum rod and a chicken bone. Strain (ᵋ) is the change of length of the material over the initial length. As we increase the stress on the material, there will be an increase on the strain on the material as well. Stress is the force (F) over cross-sectional area (A) applied on the material. The area is constant, so stress can
Words: 610 - Pages: 3
