...increased network traffic, and a lot more collision domains. The network load was severely affected because on the increase in demand within the network. The network was also affected because of the addition of more nodes on the network the traffic is doubled. I would highly recommend the use of Network Load Balancing which scales the performance of a server-based programs and it also helps to evenly distribute the load and traffic through the network. Server load balancing should also be put into place into order to lighten the load that is on the servers. Strategic planning expansion should also be practiced because it is nice to come prepared for the worst instead of just crossing your fingers. I would setup the first server followed by the 30 nodes that I connected to the switch I then put a load onto the network and ran my tests, making sure that the results were positive. Next I would add an expansion onto the network so I added another switch and connected 15 nodes to that. Finally, I would re-run the networks test at which led to the increase in nodes which would put a much higher strain on the network and the server load in general. This looks all good on paper but unfortunately I was unable to complete all the steps. The creation of the network is a little more complicated and required much more pratice than I expected. I spent four hours trying to complete this task. This was more time than I was instructed to spend. But I love...
Words: 288 - Pages: 2
...analyze, and evaluate the significant influences that work for or against its strategic objectives (Sultz & Young, 2009). Strategically planning will help aid Sandwich Blitz with the decision of expanding and locating new locations. It allows for all management persons to get involved in the process. Although I believe that the expansions should be on small scale because this allows them time for growth if the new expansion takes off. The biggest STRENGTH of Sandwich Blitz is that they have the resources to open two additional locations if good locations can be found. Another strength would be, that they have the staff to move to these new locations. This also allows for low level management to get involved in the marketing of the new expansions. A major WEAKNESS of Sandwich Blitz is that due to the recent economic downturn, the larger park offices have been affected and this could affect business because people are probably not shopping in these areas too much. They would probably have to come up with cheaper menus and do specials to attract business which could be costly. The OPPORTUNITY for Sandwich Blitz would be that the expansion allows for more business especially if it is moved to another city. The new city may not have top competitors or mimics of Sandwich Blitz and this allows to them to enter another market. Another opportunity is that it can bring about new business and more customers for the franchise. It also gives them the opportunity to create new...
Words: 355 - Pages: 2
...CIST 1122 Hardware Installation & Maintenance Final Exam Answers Follow Below Link to Download Tutorial https://homeworklance.com/downloads/cist-1122-hardware-installation-maintenance-final-exam-answers/ For More Information Visit Our Website ( https://homeworklance.com/ ) Email us At: Support@homeworklance.com or lancehomework@gmail.com 1. A HDMI cable is generally used for what computer functions? 2. Where does one go to verify correct hardware settings in a system? 3. What connectors from a power supply should be used with a graphics expansion card? 4. What MUST be performed when installing a Video card for use? 5. What expansion slots is characterized by having an x16 speed? 6. What types of Ethernet should be used if a technician has no choice but to run cable along fluorescent lighting arrays in a suspended ceiling? 7. What laptop accessories would MOST likely be used to support multiple expansion ports? 8. What connector types is used on a CAT5 cable? 9. What can be implemented on a WAP to ensure that only certain client machines can access it? 10. Secure web traffic uses what port? 11. What features can be configured with keyboards to assist users with disabilities? 12. What features makes logical processor cores appear as physical cores to the operating system? 13. What storage media would be used to build a cost-effective RAID 5 array? 14. A network consisting of numerous geographically dispersed networks that cover a large physical distance...
Words: 1196 - Pages: 5
...CIST 1122 Hardware Installation & Maintenance Final Exam Answers Follow Below Link to Download Tutorial https://homeworklance.com/downloads/cist-1122-hardware-installation-maintenance-final-exam-answers/ For More Information Visit Our Website ( https://homeworklance.com/ ) Email us At: Support@homeworklance.com or lancehomework@gmail.com 1. A HDMI cable is generally used for what computer functions? 2. Where does one go to verify correct hardware settings in a system? 3. What connectors from a power supply should be used with a graphics expansion card? 4. What MUST be performed when installing a Video card for use? 5. What expansion slots is characterized by having an x16 speed? 6. What types of Ethernet should be used if a technician has no choice but to run cable along fluorescent lighting arrays in a suspended ceiling? 7. What laptop accessories would MOST likely be used to support multiple expansion ports? 8. What connector types is used on a CAT5 cable? 9. What can be implemented on a WAP to ensure that only certain client machines can access it? 10. Secure web traffic uses what port? 11. What features can be configured with keyboards to assist users with disabilities? 12. What features makes logical processor cores appear as physical cores to the operating system? 13. What storage media would be used to build a cost-effective RAID 5 array? 14. A network consisting of numerous geographically dispersed networks that cover a large physical distance...
Words: 1196 - Pages: 5
...Hardware Components |Components |Devices |Requirements Met | |Input Device |Wireless Keyboard |Create text documents with flexibility | | |All-in-One Scanner |Create digital copy of files | | |HD Web Cam w/ Mic |Create video and still image files | | |5-in-1 Card Reader |Creates copy video, still image files | | |Wireless Mouse |Allows flexibility of selection device | | | | | | | | | |Output Devices |23”HD 3D LED Monitor |High quality visual presentation | | |Wireless Laser Printer |High quality hardcopy presentation ...
Words: 659 - Pages: 3
...------------------------------------------------- Step 1: Choose mode table glossary small large 3" x 5" index card Want to print a test? Click here. Alphabetize Flip terms and definitions ------------------------------------------------- Step 2: Open the file Open PDF ------------------------------------------------- Step 3: Print it! ← Back to Set | PC Pro Certification Practice Exam A+ 220-801Study online at quizlet.com/_ipciw | 1. | An administrator wants to prevent people outside of the building from accessing a new wireless router. Which of the following is the LEAST labor intensive method to use while setting up new workstations? A. Turn SSID broadcast off B. Use wireless encryption C. Institute MAC filtering D. Setup static IP addresses | | A. Turn SSID broadcast off | 2. | After installing a bar code reader, which of the following is commonly done to configure the reader? A. Scan in program codes B. Enable the code reader in the BIOS C. Use Device Manager to enable I⁄R ports D. Adjust jumper switches | | A. Scan in program codes | 3. | After installing a new serial port card in a computer, the communication parameters need to be configured. Which of the following is the MOST common communication configuration for a serial port? A. Eight data bits, even parity, two stop bits B. Seven data bits, no parity, one stop bit C. Eight data bits, no parity, one stop bit D. Seven data bits, even...
Words: 11959 - Pages: 48
...The Complete Guide To: How to Build a Computer from Scratch. By Whitson Gordon [PDF Created by Sarvesh Lad] Lesson 1: Hardware Basics Building a computer from scratch gives you the perfect machine for your needs, but it can be daunting the first time around. In this edition of Lifehacker Night School, we'll be taking you through the buying, building, and installation process step-by-step. Today, we're going to start with a little computer hardware basics. While you could just go to the store and buy a Dell, you might find that you're happier with a custom-built machine. Building a PC from the ground up means it's perfectly crafted to fit your needs, whether you're a hardcore gamer, video editor extraordinaire, or you're just trying to build a low- or high-powered home theater PC. In some instances, you may save some money, and in all instances you'll have accomplished a project that you'll benefit from for years—a pretty great feeling in and of itself. That said, building is much more time consuming than buying, and your first time through, it can be daunting. This week's Night School series will walk you through building your first (or second, or third) computer from start to finish. Today, we'll be talking about the first step in any computer build: brainstorming what kind of machine you're looking to make and what that means for your hardware. The Types of Machines and their Ballpark Costs Much like we did in our original spec-crafting feature, the the first thing...
Words: 10432 - Pages: 42
...Step 1 User boots her computer and hears a sequence of six beeps. Step 2 a cause could be an expansion card has failed. Step 3 you would do a physical check and uninstall and reinstall any expansion cards that you have connected to the motherboard. When you do that restart the computer and see if you get that same beep sequence or any. Step 4 you should check run a test on all expansion cards.Step 5 once you ran many tests and you fixed to problem you then verify the computer is working. Step 6 you found that the expansion slots were a problem and you replaced them with new ones. Now your computer is working fine. Step 1 the user boot their computer and hear a sequence of ten beeps. Step 2 a cause could be by a damaged expansion card. Step 3 after pulling the cards out you still has a problem. Step 4 you then replace the motherboard and that should fix the problem. Step 5 you restart our computer and that the computer was fixed. Step6 you found the problem was your motherboard, you replaced the motherboard and the problem was fixed. Task 2 Step 1 you opened the internet and you can’t open this website. Step 2 cause could be you are not connected to the internet, the website is encountering problems or there might be typing error in the address. Step 3 try to open a regular site like Google to see if you’re encountering problems. Then you could look at your Ethernet cable to see if it’s connected to the computer. Last try to find the site using Google in case you’re having...
Words: 343 - Pages: 2
...power switch allows normal OS shutdown unlike the back switch, which immediately cuts power. Second is the NLX, which is for low end personal computer, supports riser card which adds expansion slots. Third is the BTX which is compatible with all ATX functions but is designed for better airflow and cooling. By having an intake vent at the front and an exhaust vent on the back along with having the CPU and memory modules installed parallel to the direction of the airflow, the BTX achieves its cooling functions. Communication buses are also explained. They are copper tracing on the bottom of the mother board and they make up the bus system. Often described as highways. Buses connect to various components and allows power and data between the CPU, Hard Drive, key board, mouse, USB devices, sound cards and any other components. System bus is the largest and fastest bus, it connects to the mother board and it carries data between the CPU and the mother board and vice versa. There are various connectors on a mother board one of them is the power connector known as the p1 connector. P1 has a 20 pin connector or a 24 pin connector. The 40 pin IDE, 34 pin Floppy drive connector, SATA connectors and the 50 or 68 pin SCSI otherwise known as Scuzzy. Today’s computers uses PCI, PCIX, PCIe(express) and AGP expansion slots to connect peripheral devices and system of buses.PCI is fast, PCIX is faster, PCIe is the newest, fastest...
Words: 647 - Pages: 3
...Widget Wonders is a worldwide leader in widgets. They are building a state-of-the-art facility to manufacture and distribute the next generation of widgets. SNHUConsulting has been retained to implement information technology on the expansion project. The new facility for Widget Wonders will be the main manufacturing and distribution center in the United States. The network in the distribution center will connect to the main network located at headquarters. The various departments in the distribution center, the number of employees, and the department needs are listed below. Sales: The 50 employees in this department require mobility to access company resources while visiting customers and presenting at sales meetings and conferences. Manufacturing: The 45 employees in this department require access to word processing and spreadsheet programs and the internet. Inventory Control: The 30 employees in this department require mobility and power to access database systems. Research and Development: The 20 employees in this department require graphics and computer-aided design (CAD) programs. MIS: The 5 employees in this department require additional processor and memory requirements to support administration tasks. As part of the expansion team, you will determine the hardware requirements for each department. Widget Wonders...
Words: 718 - Pages: 3
...Short Answer Computer Structure and Logic May 11th, 2016 Professor Martin Rachel Baldwin The major concepts of the motherboard include; peripherals, Interface cards, daughter cards: sound cards, video cards, network cards, hard drives, TV tuner cards, cards providing extra USB or FireWire slots and a variety of other components. A peripheral is a device that is used to put information into get information out of the country. The Daughter cards or daughterboard contains plug sockets connectors for other boards to attached to. Daughterboards only have internal connections. Next is the sound cards. The sound cards is an internal computer expansion card. It facilitates economical input of auto signals to and from a computer found under control of a computer programs. Video cards is a type of expansion card this also generates a feed of output images to the display. They are frequently advertised as dedicated graphics cards. Which is a big difference between the integrated graphics. Sometimes video cards are called graphic add- in- boards. Network cards is a computer hardware component that connects a computer to a computer network. (Wi-Fi connection) The hard drives is a data storage device used to store and retrieving digital information using one or more rigid(hard) rapidly rotating disks platters coated with megnetic material. TV tuner card is a kind of television that allows TV signals to be retrieved by a computer. Most TV tuners function as video capture cards which allows...
Words: 583 - Pages: 3
...add-on cards. Most desktop computers have a form factor that is some variant of ATX. A case designed for an ATX motherboard and power supply may take on several external forms, such as a vertical tower (designed to sit on the floor, height > width) or a flat desktop (height < width). Computer cases usually include: sheet metal enclosures for a power supply unit and drive bays; a rear panel that can accommodate peripheral connectors protruding from the motherboard and expansion slots; a power button, a reset button, and LEDs to indicate power status as well as hard drive and network activity. Major component locations * The motherboard is usually screwed to the case along its largest face, which could be the bottom or the side of the case depending on the form factor and orientation. * Form factors such as ATX provide a back panel with cut-out holes to expose I/O ports provided by integrated peripherals, as well as expansion slots which may optionally expose additional ports provided by expansion cards. * The power supply unit is often housed at the top rear of the case; it is usually attached with four screws...
Words: 1691 - Pages: 7
...The Effect of Compiler Optimizations on Pentium 4 Power Consumption John S. Seng Dean M. Tullsen Dept. of Computer Science and Engineering University of California, San Diego La Jolla, CA 92093-0114 jseng,tullsen @cs.ucsd.edu Abstract This paper examines the effect of compiler optimizations on the energy usage and power consumption of the Intel Pentium 4 processor. We measure the effects of different levels of general optimization and specific optimization. We classify general optimizations as those compiler flags which enable a set of compiler optimizations. Specific optimizations are those which can be enabled and disabled individually. The three specific optimizations we study are loop unrolling, loop vectorization, and function inlining. The binaries used in this study are generated using the Intel C++ compiler, which allows fine-grained control over each of these specific optimizations. ¡ 1. Introduction The power consumption of general purpose microprocessors has reached a point where the problem has to be addressed at various levels of system design. Many circuit, architecture, and software algorithm techniques exist to reduce power, but one often overlooked area is the effect of the program code on power consumption. Some research has been done studying the effect of compiler optimizations on power consumption [8, 9]; this work has been generally limited to using architecture-level power models for power estimation. In this work we examine the effect of the compiler...
Words: 4099 - Pages: 17
...components of a computer mother board are the processor, memory, chipset, expansion slots, and IO bank. The Processor is the brain of the computer. The processor is the chip where all of the computing is completed. The processor is usually removable and inserted into a socket. The processor can be attached directly to the mother board. The processor is normally protected by a heat sink which assists in removing heat and protects the processor from burning out. The memory is where the computers stores all of the information. The computer memory is usually installed on a board called a SIMMs. SIMMs stands for Single Inline Memory Module. Single Inline Memory Modules come in different sizes. These sizes include 2G, 4G, 8G, and up. You can have one memory installed on a board or you can have multiple memory installed. The amount of memory that is allowed on a board depends on various factors. These factors include the processor, the board itself, and the BIOS. The memory is usually removable. The chipset is a term that refers to a chip or a set of chips. The Chipset is a link between the processor and the outside world. The chipset controls the USB ports, keyboard, mouse, and hard drives. The Chipset generates the sound that the computer makes. The Chipset creates the images that you see in the screen. The Chipset is usually attached directly to the mother board and usually has heat sinks attached to them. The Expansion Slots are connectors that allow you to attach cards on the computer...
Words: 574 - Pages: 3
...Associate Program Material Appendix B Computer Hardware Simulator The Computer Hardware Simulator (CHS) is designed to provide you with an opportunity to explore and familiarize yourself with external and internal computer hardware parts and components. You will use the computer featured in the CHS throughout this course to help with assignments. Explore and examine the different pages and video clips in the CHS at https://ecampus.phoenix.edu/secure/aapd/UOPHX/IT280/Computer_Hardware_Simulator.html Your assignments require different information featured in the CHS to complete your work. Some information is basic; you may need to search the Internet to complete necessary information. Below is a chart where you can fill in the CHS computer’s make and model, part numbers, and other information. Keep this chart handy as a reference throughout the course. Computer Hardware Simulator Computer |Component |Brand |Part Number | |Computer make and model |Dell Optiplex 755 Minitower | | | |Operating system Microsoft®Windows® | | |Motherboard |Intel (OEM for Dell Optiplex755) |0GM819 GM819 | |Processor |Intel Celeron...
Words: 390 - Pages: 2
