Give two differences between EEPROM and Flash memory. EEPROM is a read only memory, which can re erased and reprogrammed. Flash memory is a memory that holds data even when the power is not on. 2. Indicate the use of each memory in the microcontroller. In other words, state which one is used for code, program variables, and variables that must remain when the power is turned off. • Code is stored in flash ( non-volatile memory, where the code will be saved even when there is no power) • Program
Words: 572 - Pages: 3
------------------------------------------------- University of Ottawa School of Electrical Engineering and Computer Science (EECS) ELG 4913 Final Report Project Title: Solar Panel Enhancement System Executive Summary The project is to enhance the functionality of the solar panels. Our project is divided onto three main parts. Snow and dust can prevent the
Words: 5076 - Pages: 21
Temperature control system for PEM Fuel cell Fuel cell research technology Group Babol University of Technology S.M.Rakhtala, T.Fadaiian R.Ghaderi, A.Ranjbar and M.Shakeri mh_rakhtala@stu.nit.ac.ir Abstract In This paper, design of the temperature control system of PEM fuel cell is developed with integrated control techniques by Atmega 128 micro-controller along with optimized performance of fuel cell system. The temperature control system will guarantee the correct performance of fuel cell around
Words: 3037 - Pages: 13
0, Embedded Linux-2.6, Uc/OS-II and Android 2.1, which provide drivers for all the bottom interfaces and devices and utility applications. OK6410-B is an Embedded Computer (Single Board Computer) based on the 667MHz Samsung S3C6410 (ARM11) microcontroller. OK6410-B embodies abundant of built-in resources and powerful video processing capacity, which make the OK6410-B reliable for the development of higher-end
Words: 2960 - Pages: 12
camera we can monitor the area. This project is designed around a Microcontroller which forms the control unit of the project. According to this project, an RF transmitter is used to transmit the control signals, which controls the direction of the robot. In the same way, RF receiver which is placed on the robot receives the RF signals according to which the direction of the robot is controlled. The microcontroller plays important role in controlling the direction according to RF signals
Words: 344 - Pages: 2
Table Of Contents Chapter One .................................................................................................................................... 3 Introduction ..................................................................................................................................... 3 1.1 Statement of the problem ...................................................................................................... 4 1.2 Objectives .....................................
Words: 5593 - Pages: 23
Software Requirements Specification FOR AUTOMATIC RAILWAY GATE CONTROL SYSTEM PREPARED BY: SHIKHAR MALIK (13BCE0494) EMAIL: shikhar.malik2013@vit.ac.in SUBMITTED TO: PROF. AKILA VICTOR
Words: 1517 - Pages: 7
for audio streaming. Figure 7.1 Shows BT modules Connects with Headset 7.3) Transmitting Audio For transmitting heart beat audio that is coming from Analog circuitry firstly send to MSP430 microcontroller where analog data is converted into Digital data now this sampled data has been send to Bluetooth module over UART interface MSP 430 G2553 BT MODULE
Words: 808 - Pages: 4
proponents for the whole system to run. Theoretical Framework Each of the devices is supported by different theories which we hope we would be able to integrate. A microcontroller “is a small computer on a single IC containing a processor core, memory, and a programmable Input/Output peripheral.” (http://en.wikipedia.org/wiki/Microcontroller) We will be using this device as the brain of the system. We will be using the memory of the IC to encode the program and the I/O system inside the IC to retrieve
Words: 636 - Pages: 3
Temasek Polytechnic Microcontroller Technology EMC2001 Keypad and Sensor Board 4x4 Matrix Keypad Touch Sensor Key Encoder The keypad and sensor board houses mainly the 4x4 Matrix Keypad, MM74C992 16 Key Encoder and QProx QT113 Touch Sensor. The 4x4 Matrix Keypad is an input device that can be used to interface to microcontroller (for entry of password for example). The MM74C992 16 Key Encoder provides all the required logic to encode an array of keypad switches. This requires
Words: 418 - Pages: 2
