Free Essay

Panel View Plus

In:

Submitted By tunfem
Words 7594
Pages 31
Installation Instructions

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Catalog Numbers 2711P-Kxxxx, 2711P-Txxxx, 2711P-Bxxxx, 2711P-RDxxxx, 2711PC-T10C4D1
Topic Important User Information Environment and Enclosure Hazardous Locations Wiring and Safety Guidelines About the PanelView Plus 700 to 1500 Terminals Parts List Required Tools Install the Terminal DC Power Connections AC Power Connections Battery Precautions Troubleshooting Specifications Additional Resources Page 2 3 4 8 8 10 10 10 16 20 22 24 28 30

About This Publication
This document provides instructions on how to install these devices in a panel. • Factory-assembled PanelView Plus or PanelView Plus CE 700 to 1500 terminals • PanelView Plus or PanelView Plus CE 700 to 1500 display modules • Factory-assembled PanelView Plus Compact 1000 terminal For complete information on installing, wiring, and troubleshooting the terminals, refer to the publications listed under Additional Resources.

2

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://literature.rockwellautomation.com) describes some important differences between solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable. In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited. Throughout this manual, when necessary, we use notes to make you aware of safety considerations. WARNING Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. Identifies information that is critical for successful application and understanding of the product. Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and recognize the consequences.

IMPORTANT ATTENTION

SHOCK HAZARD Labels may be on or inside the equipment (for example, a drive or motor) to alert people that dangerous voltage may be present.

BURN HAZARD Labels may be on or inside the equipment (for example, a drive or motor) to alert people that surfaces may reach dangerous temperatures.

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

3

Environment and Enclosure
ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to 2000 m (6561 ft) without derating. The terminals are intended for use with programmable logic controllers. Terminals that are AC powered must also be connected to the secondary of an isolating transformer. This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR Publication 11. Without appropriate precautions, there may be potential difficulties ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbance. Korean Radio Wave Suitability Registration - This equipment is registered for Electromagnetic Conformity Registration as business equipment (A), not home equipment. Sellers or users are required to take caution in this regard. This equipment is supplied as open-type equipment. It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. The interior of the enclosure must be accessible only by the use of a tool. The terminals meet specified NEMA Type and IEC ratings only when mounted in a panel or enclosure with the equivalent rating. Subsequent sections of this publication may contain additional information regarding specific enclosure type ratings that are required to comply with certain product safety certifications. In addition to this publication, see: • Industrial Automation Wiring and Grounding Guidelines, for additional installation requirements, publication 1770-4.1. • NEMA Standards publication 250 and IEC publication 60529, as applicable, for explanations of the degrees of protection provided by different types of enclosure.

ControlNet Communication Port
ATTENTION PanelView Plus terminals with ControlNet communications ports include a Network Applications Port (NAP). This port is for temporarily connecting programming terminals to devices on a ControlNet network, and are not intended for continuous operation.

Publication 2711P-IN001I-EN-P - November 2009

4

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Hazardous Locations
This equipment is suitable for these locations: • • • • Class I, Division 2 Groups A, B, C, D Class II, Division 2 Groups F, G Class III Ordinary, nonhazardous locations only

The following statement applies to use in hazardous locations.
WARNING Explosion Hazard • Substitution of components may impair suitability for hazardous locations. • Do not disconnect equipment unless power has been switched off and area is known to be nonhazardous. • Do not connect or disconnect components unless power has been switched off. • All wiring must comply with N.E.C. articles 501, 502, 503, and/or C.E.C. section 18-1J2 as appropriate. • Peripheral equipment must be suitable for the location in which it is used.

The terminals have a temperature code of T4 when operating in a 55 °C (131 °F) maximum ambient temperature. Do not install the terminals in environments where atmospheric gases have ignition temperatures less than 135 °C (275 °F).

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

5

Environnements dangereux
Cet équipement ne peut être utilisé que dans les environnements suivants : • • • • Classe I, Division 2, Groupes A, B, C, D Classe II, Division 2, Groupes F, G Classe III ou environnements non-dangereux

La mise en garde suivante s’applique à une utilisation en environnement dangereux.
AVERTISSEMENT DANGER D’EXPLOSION • La substitution de composants peut rendre cet équipement impropre à une utilisation en environnement dangereux. • Ne pas déconnecter l’équipement sans s’être assuré que l’alimentation est coupée ou que l’environnement est classé non dangereux. • Ne pas connecter ou déconnecter des composants sans s’être assuré que l’alimentation est coupée. • L’ensemble du câblage doit être conforme, selon le cas, aux articles 501-4(b), 502-4(b) et 503-3(b) du Code national de l’électricité des Etats-Unis. • L’équipement périphérique doit être adapté à l’environnement dans lequel il est utilisé.

Le code de température de fonctionnement des terminaux PanelView Plus et PanelView Plus CE est T4 pour une température ambiante maximale de 55 °C. N’installez pas les terminaux dans des environnements contenant des gaz atmosphériques inflammables à moins de 135 °C.

Publication 2711P-IN001I-EN-P - November 2009

6

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

USB Ports
All PanelView Plus and PanelView Plus Compact terminals contain universal serial bus (USB) ports that comply with hazardous location environments. This section details the field-wiring compliance requirements and is provided in accordance with the National Electrical Code, article 500.

Terminals Control Drawing
Associated Nonincendive Field Wiring Apparatus PanelView Plus Host Product Nonincendive Field Wiring Apparatus USB Peripheral Device

Nonincendive Field Wiring USB Port

Table 1 - PanelView Plus USB Port Circuit Parameters
Voc 5.25V DC Isc 1.68 A Ca Groups A and B 10 µF Groups C and D 10 µF Groups A and B 15 µH La Groups C and D 15 µH

Selected nonincendive field wiring apparatus must have nonincendive circuit parameters conforming with Table 2.

Table 2 - Required Circuit Parameters for the USB Peripheral Device
Vmax Imax Ci + Ccable Li + Lcable ≥ ≥ ≤ ≤ Voc Isc Ca La

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

7

Application Information
Per the National Electrical Code the circuit parameters of nonincendive field wiring apparatus for use in hazardous locations shall be coordinated with the associated nonincendive field wiring apparatus such that their combination remains nonincendive. The PanelView Plus terminals and the USB peripheral device shall be treated in this manner. The circuit parameters of the PanelView Plus USB port are given in Table 1. The USB peripheral device and its associated cabling shall have circuit parameters with the limits given in Table 2 for them to remain nonincendive when used with the PanelView Plus USB port. If cable capacitance and inductance are not known the following values from ANSI/ISA-RP 12.06.01-2003 may be used: Ccable = 197 µF/m (60 µF/ft) Lcable = 0.7 µF/m (0.20 µH/ft) Nonincendive field wiring must be wired and separated in accordance with 501.10(B)(3) of the National Electrical Code (NEC) ANSI/NFPA 70 or other local codes as applicable. This associated nonincendive field wiring apparatus has not been evaluated for use in combination with another associated nonincendive field wiring apparatus.

Symbol Definitions
Voc Isc Vmax Imax Ci Ca Open circuit voltage of the host USB port. Maximum output current of the host USB port. Maximum applied voltage rating of the USB peripheral device. Vmax shall be greater than or equal to Voc in Table 1 (Vmax ≥ Voc ). Maximum current to which the USB peripheral device can be subjected. Imax shall be greater than or equal to Isc in Table 1 (Imax ≥ Isc). Maximum internal capacitance of the USB peripheral device. Maximum allowed capacitance of the USB peripheral device and its associated cable. The sum of Ci of the USB peripheral device and Ccable of the associated cable shall be less than or equal to Ca (Ci + Ccable ≤ Ca). Maximum internal inductance of the USB peripheral device. Maximum allowed inductance of the USB peripheral device and its associated cable. The sum of Li of the USB peripheral device and Lcable of the associated cable shall be less than or equal to La (Li + Lcable ≤ La).

Li La

Publication 2711P-IN001I-EN-P - November 2009

8

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Wiring and Safety Guidelines
Use publication NFPA 70E, Electrical Safety Requirements for Employee Workplaces, IEC 60364 Electrical Installations in Buildings, or other applicable wiring safety requirements for the country of installation when wiring the devices. In addition to the NFPA guidelines: • • • • connect the device and other similar electronic equipment to its own branch circuit. protect the input power by a fuse or circuit breaker rated at no more than 15 A. route incoming power to the device by a separate path from the communication lines. cross power and communication lines at right angles if they must cross. Communication lines can be installed in the same conduit as low-level DC I/O lines (less than 10V). • shield and ground cables appropriately to avoid electromagnetic interference (EMI). Grounding minimizes noise from EMI and is a safety measure in electrical installations. For more information on grounding recommendations, refer to the National Electrical Code published by the National Fire Protection Association. For more information, refer to Wiring and Grounding Guidelines for PanelView Plus/PanelView Plus CE Devices Technical Data, publication 2711P-TD001. You can find this publication in the Literature Library website, http://literature.rockwellautomation.com.

About the PanelView Plus 700 to 1500 Terminals
The PanelView Plus terminals have these modular components: • Display module (700, 1000, 1250, and 1500) • Logic module with AC or DC power, CompactFlash card slot, Ethernet port, serial port, and USB ports • Internal CompactFlash card with firmware or operating system, RAM memory (SO-DIMM) • Communication module for specific communication protocols These items can be ordered as separate components for field installation or factory assembled per your configuration. The base-configured unit includes the display module and the logic module with internal CompactFlash and RAM.

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

9

Modular Components
Communication Module Power Input, AC or DC Logic Module Display Module

Ethernet Port CompactFlash Card Slot USB Ports Serial Port

If the modules are ordered separately, attach the logic and communication module to the display module before panel installation. See the instructions shipped with each module. The logic module for the terminals is available with or without RAM and CompactFlash preinstalled. If memory is ordered separately, you must install the memory before attaching the logic module to the display module. See the instructions shipped with the logic module.

About the PanelView Plus Compact 1000 Terminal
The PanelView Plus Compact 1000 terminal has a fixed configuration. It does not support communication modules, or the replacement of the logic module. The 1000 terminal contains a non-isolated DC power supply.

Compact Flash

Power Input, 24V DC

Ethernet Port USB Ports RS-232 Serial Port

The PanelView Plus Compact 1000 terminal has these features: • • • • • • 1000 touch screen display module USB ports (2) RS-232 serial port 10/100Base T Ethernet port Power input, 24V DC non-isolated CompactFlash Type 1 card slot

Publication 2711P-IN001I-EN-P - November 2009

10

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Parts List
These items are shipped with the terminals: • • • • Power terminal block Mounting clips FactoryTalk View software preloaded Installation instructions and panel cutout template

Required Tools
These tools are required for panel installation: • Panel cutout tools • Small, slotted screwdriver • Torque wrench (lb•in)

Install the Terminal
Before installing the terminal in a panel, review the following topics: • Mounting clearances • Panel cutout dimensions • Product dimensions

Mounting Clearances
Allow adequate clearance around the terminal, inside the enclosure, for adequate ventilation. Consider heat produced by other devices in the enclosure. The ambient temperature around the terminals must be between 0…55 °C (32…131 °F). These minimum clearances are required for ventilation. • • • • Top clearance: 51 mm (2 in.) Bottom clearance: 102 mm (4 in.) Side clearances: 25 mm (1 in.) Back clearance: 25 mm (1 in.)

Minimum side clearance for insertion of memory card is 102 mm (4 in.).

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

11

Panel Cutout Dimensions
Use the full size template shipped with your terminal to mark the cutout dimensions.
Terminal Type 700 Keypad or Keypad and Touch 700 Touch 1000 Keypad or Keypad and Touch 1000 Touch 1250 Keypad or Keypad and Touch 1250 Touch 1500 Keypad or Keypad and Touch 1500 Touch Height, mm (in.) 167 (6.57) 154 (6.08) 224 (8.8) 224 (8.8) 257 (10.11) 257 (10.11) 305 (12.00) 305 (12.00) Width, mm (in.) 264 (10.39) 220 (8.67) 375 (14.75) 305 (12.00) 390 (15.35) 338 (13.29) 419 (16.50) 391 (15.40)

Mount the Terminal in a Panel
Mounting clips secure the terminal to the panel. The number of clips you use (4, 6, or 8) varies by terminal type.

ATTENTION

Disconnect all electrical power from the panel before making the panel cutout. Make sure the area around the panel cutout is clear. Take precautions so metal cuttings do not enter any components already installed in the panel. Failure to follow these instructions may result in personal injury or damage to panel components.

Follow these steps to mount the terminal in a panel. 1. Cut an opening in the panel by using the panel cutout shipped with the terminal. 2. Make sure the terminal sealing gasket is properly positioned on the terminal.

Publication 2711P-IN001I-EN-P - November 2009

12

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

This gasket forms a compression type seal. Do not use sealing compounds.

Sealing Gasket

3. Install the legend strips before installing the terminal if you are using keypad legend strips on keypad terminals. Be careful not to pinch the legend strip during installation. 4. Place the terminal in the panel cutout. 5. Slide the ends of the mounting clips into the slots on the terminal.
Mounting Clip Slot Mounting Clip

6. Tighten the mounting clip screws by hand until the gasket seal contacts the mounting surface uniformly.

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

13

7. Tighten the mounting clip screws to a torque of 0.90…1.1 N•m (8…10 lb•in) by using the specified torque sequence, making sure not to overtighten.
1 4 Clips 3 2 4 2 6 4 1 5 6 Clips 3 3 8 Clips 7 5 2 4 1 6 8

ATTENTION

Tighten the mounting clips to the specified torque to provide a proper seal and prevent damage to the product. Rockwell Automation assumes no responsibility for water or chemical damage to the product or other equipment within the enclosure because of improper installation.

Product Dimensions
The table provides product dimensions for the terminals including depth dimensions for the: • base configured unit (display module and logic module). • base configured unit with communication module.
Height, Approx., mm (in.) 193 (7.58) 179 (7.04) 248 (9.77) 248 (9.77) 282 (11.12) 282 (11.12) 330 (12.97) 330 (12.97) Width, Approx., mm (in.) 290 (11.40) 246 (9.68) 399 (15.72) 329 (12.97) 416 (16.36) 363 (14.30) 469 (18.46) 416 (16.36) 65 (2.55) display to logic module 93 (3.65) display to comm module

Terminal Type 700 Keypad or Keypad and Touch 700 Touch Screen 1000 Keypad or Keypad and Touch 1000 Touch Screen 1250 Keypad or Keypad and Touch 1250 Touch Screen 1500 Keypad or Keypad and Touch 1500 Touch Screen

Depth, Approx., mm (in.) 55 (2.18) display to logic module 83 (3.27) display to comm module

Publication 2711P-IN001I-EN-P - November 2009

14

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

The illustration shows product dimensions for the PanelView Plus and PanelView Plus Compact 1000 touch only terminals. The other size terminals look similar. Measurements are in mm (in.).

1000 Terminal Dimensions

Keypad or Keypad & Touch

248 (9.77)

399 (15.72) a 55 (2.18) Display to Logic Module b 83 (3.27) Display to Comm Module a

b

Touch Screen

248 (9.77)

329 (12.97) a 55 (2.18) Display to Logic Module b 83 (3.27) Display to Comm Module

b

a

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

15

Ethernet Wiring
Use Belden 7921A shielded Ethernet Category 5e cable according to TIA 568-B.1 and RJ45 connector according to IEC 60603-7 for compliance with Marine emissions limits and European Union 89/336/EEC EMC Directive. The maximum cable length between the terminal’s Ethernet port and a 10/100 Base-T port on an Ethernet hub (without repeaters or fiber) is 100 m (328 ft).

Remove and Install the Power Terminal Block
The terminals are shipped with a power terminal block installed. You can remove the terminal block for ease of installation, wiring, and maintenance.
WARNING Explosion Hazard Substitution of components may impair suitability for hazardous locations. Do not disconnect equipment unless power has been switched off and area is known to be nonhazardous. Do not connect or disconnect components unless power has been switched off. All wiring must comply with N.E.C. articles 501, 502, 503, and/or C.E.C. section 18-1J2 as appropriate. Peripheral equipment must be suitable for the location in which it is used.

ATTENTION

Disconnect all power before installing or replacing components. Failure to disconnect power may result in electrical shock or damage to the terminal.

• Series A to D, DC logic modules use a 3-position terminal block. • Series E or later, DC logic modules use a 2-position terminal block. • All logic modules with an AC power input use a 3-position terminal block.

Publication 2711P-IN001I-EN-P - November 2009

16

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Follow these steps to remove the terminal block. 1. Loosen the two screws that secure the terminal block. 2. Gently pull the terminal block away from the connector.

2-position DC Terminal Block (series E or later)

3-position AC or DC Terminal Block

Follow these steps to install the terminal block. 1. Reattach the terminal block to the connector until seated. 2. Tighten the two screws that secure the terminal block to the connector.

DC Power Connections
DC-powered PanelView Plus devices have an integrated 24V DC power supply. Both isolated and non-isolated power supplies have these ratings: • 24V DC nominal (18…32V DC) • 70 W maximum (2.9 A at 24V DC) The power supply is internally protected against reverse polarity of the DC+ and DCconnections. Connecting DC+ or DC- to the earth/ground terminal may damage the device. The input power terminal block supports these wire sizes.

Wire Specifications for DC Input Power Terminal Block
Logic Module Series A to D Series E and later
(1)

Wire Type Stranded or solid Cu 90 °C (194 °F)

Dual-wire Gauge(1) 22…16 AWG

Single-wire Gauge

Terminal Screw Torque 0.23…0.34 N•m (2…3 lb•in) 0.56 N•m (5 lb•in)

22…14 AWG

Two-wire max per terminal.

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

17

External Power Supply For Non-isolated DC Terminals
TIP To identify non-isolated DC logic modules refer to the PanelView Plus Terminals user manual, publication 2711P-UM001.

Use a single, 24V DC power supply to power each PanelView Plus device, such as catalog number 2711P-RSACDIN. Using a separate, isolated and ungrounded source to power each terminal prevents ground loop currents from damaging the terminals. The output on the power supply must be isolated from the input and not connected to earth/ground.
ATTENTION Use a Class 2 or SELV supply as required by local wiring codes for your installation. The Class 2 and SELV power sources provide protection so that under normal and single-fault conditions, the voltage between the conductors, and between the conductors and functional earth or protective earth does not exceed a safe value.

Multiple AC Power Supplies to Power Multiple DC Terminals
L2 L1 L2 L1

AC/DC Power Supply
(2711P-RSACDIN) dc+ Circuitry dc-

AC/DC Power Supply
(2711P-RSACDIN) dc+ Circuitry dc-

PanelView Plus

PanelView Plus

Publication 2711P-IN001I-EN-P - November 2009

18

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

External Power for Isolated DC Terminals
TIP Isolated DC logic modules are identified by catalog number 2711P-RPxDx.

Use an SELV or PELV 24V DC power supply, such as catalog number 2711P-RSACDIN, to power the isolated DC PanelView Plus terminal. The isolated DC terminals may be powered by the same power source as other equipment.
ATTENTION Use an SELV or PELV supply as required by local wiring codes for your installation. The SELV and PELV power sources provide protection so that under normal and single fault conditions, the voltage between conductors and earth ground does not exceed a safe value.

Earth/Ground Connection
PanelView Plus devices with a DC power input have a earth/ground terminal that you must connect to a low-impedance earth/ground. The earth/ground connection is on the rear of the display module.
IMPORTANT The earth/ground connection to ground is mandatory. This connection is required for noise immunity, reliability, and Electromagnetic Compliance (EMC) with the European Union (EU) EMC directive for CE-mark conformance. This connection is required for safety by Underwriters Laboratory.

The earth/ground terminal requires a minimum wire gauge.

Earth/Ground Wire Specifications for DC Power
Symbol GND Wire Type Stranded or solid Cu 90 °C (194 °F) Wire Gauge 14…10 AWG Terminal Screw Torque 1.13…1.36 N•m (10…12 lb•in)

On most PanelView Plus devices, the earth/ground terminal is internally connected to the DC- terminal within the product.
ATTENTION

Damage or malfunction can occur when a voltage potential exists between two separate ground points. Make sure the terminal does not serve as a conductive path between ground points at different potentials.

The PanelView Plus devices have isolated and non-isolated communication ports. For more information refer to the PanelView Plus Terminals User Manual, publication 2711P-UM001. Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

19

Connect DC Power
WARNING Explosion Hazard - Do not disconnect equipment unless power has been switched off and area is known to be nonhazardous. Disconnect all power before installing or replacing components. Failure to disconnect power may result in electrical shock or damage to the terminal.

Follow these steps to connect the terminal DC power. 1. Verify that the terminal is not connected to a power source. 2. Secure the DC power wires to the terminal block. Follow the markings on the terminal blocks and the terminal for proper connections. 3. Secure the earth/ground wire to the earth/ground terminal screw at the bottom of the display.

DC Power Supply Connections
3-position Terminal Block (series A to D logic modules) –

+

DC- DC+ 2-position Terminal Block (series E or later logic modules)
GND

– Earth/Ground to Ground Bus GND

+

DC - DC+

Publication 2711P-IN001I-EN-P - November 2009

20

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

AC Power Connections
PanelView Plus devices with an integrated AC power supply have these power ratings: • 85…264V AC (47…63 Hz) • 160V A max The input power terminal block supports these wire sizes.

Wire Specifications for AC Input Power Terminal Block
Wire Type Stranded or solid
(1)

Dual-wire Gauge(1) 22…16 AWG

Single-wire Gauge 22…14 AWG

Terminal Screw Torque 0.56 N•m (5 lb•in)

Cu 90 °C (194 °F)

Two-wire max. per terminal.

Protective Earth and Functional Earth Connection
PanelView Plus devices with an AC power input have both a protective earth and functional earth terminal that you must connect to a low-impedance earth ground. • Protective earth terminal is on the power input terminal block. • Functional earth connection is on the back of the display.
ATTENTION The functional earth and protective earth connections to ground are mandatory. The functional earth ground connection is required for electromagnetic compliance (EMC) with the EU (European Union) EMC directive for CE-mark conformance. The protective earth ground connection is required for safety and regulatory compliance.

IMPORTANT

On PanelView Plus devices with an AC power input, you must connect both protective earth and functional earth to ground.

The protective earth and functional earth terminals require a minimum wire gauge.

Functional Earth and Protective Earth Wire Specifications for AC Power
Connection Protective earth Functional earth Wire Type Stranded or solid Stranded or solid Cu 90 °C (194 °F) Cu 90 °C (194 °F) Wire Gauge 14…12 AWG 14…10 AWG Terminal Screw Torque 0.56 N•m (5 lb•in) 1.13… 1.36 N•m (10…12 lb•in)

GND

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

21

Connect AC Power
WARNING Explosion Hazard - Do not connect or disconnect equipment while circuit is live unless area is known to be nonhazardous. Disconnect all power before installing or replacing components. Failure to disconnect power may result in electrical shock and/or damage to the terminal.

ATTENTION

Improper wiring of power terminals may result in voltage at the communication connector shells. Refer to the following figure when wiring. Do not apply power to the terminal until all wiring connections have been made. Failure to do so may result in electrical shock.

Follow these steps to connect the terminal to AC power. 1. Verify that the terminal is not connected to a power source. 2. Secure the AC power wires to the terminal block. Follow the markings on terminal blocks and terminal for proper connections. 3. Secure the protective earth ground wire to the marked position of the power input terminal block. 4. Secure the functional earth ground wire to the functional earth ground screw on the back of the display to ground bus.

L1 L2/Neutral Protective Earth to Ground Bus

GND

Functional Earth Ground to Ground Bus

5. Apply AC power to the terminal.

Publication 2711P-IN001I-EN-P - November 2009

22

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Battery Precautions
WARNING When you connect or disconnect the battery an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed and the area is nonhazardous before proceeding. For safety information on the handling of lithium batteries, including handling and disposal of leaking batteries, see Guidelines for Handling Lithium Batteries, publication AG 5-4. Replace the battery only with the indicated catalog number. Do not dispose of battery in a fire or incinerator. Dispose of used batteries in accordance with local regulations. Store batteries in a cool, dry environment. We recommend 25 °C (77 °F) with 40…60% relative humidity. You may store batteries for up to 30 days between -45…85 °C (-49…185 °F), such as during transportation. To avoid possible leakage, do not store batteries above 60 °C (140 °F) for more than 30 days.

Replace the Battery
Follow these steps to replace the lithium battery in the logic module of PanelView Plus or PanelView Plus Compact terminals. 1. Disconnect power from the terminal. 2. Place the terminal, display side down, on a flat stable surface. 3. Detach the communication module, if attached, from the logic module by removing the four screws. 4. Loosen the six captive screws that attach the logic module to the display module.
Communication Module Screw Logic Module Captive Screw

Display Module

5. Carefully lift the logic module away from the terminal and turn over to expose the circuit board.

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

23

6. Locate the battery on the circuit board.

Lift up the edge of the battery indicated by the arrow.

7. Remove the battery by lifting up the side of the battery. 8. Insert the new battery.
IMPORTANT Use only replacement battery catalog number 2711P-RY2032.

9. Reattach the logic module by aligning the two connectors on the bottom of the module with the connectors on the terminal.

10. Push down on the logic module until it is firmly seated. 11. Tighten the six captive screws that secure the logic module to a torque of 0.58 N•m (5…7 lb•in).

Publication 2711P-IN001I-EN-P - November 2009

24

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

12. Reattach the communication module, if necessary, and tighten the four screws to a torque of 0.58 N•m (5…7 lb•in).
This product contains a hermetically sealed lithium battery which may need to be replaced during the life of the product. At the end of its life, the battery contained in this product should be collected separately from any unsorted municipal waste. The collectioin and recyling of batteries helps protect the environment and contributes to the conservation of natural resources as valuable materials are recovered.

Troubleshooting
If the terminal is not operating correctly, check the power, display settings, status indicators, and review the system startup and error messages.

Check for Adequate Power
A terminal that does not receive adequate power could cause unpredictable behavior. Verify the power requirements in the Specifications table.

Check Status Indicators
The terminal has two status indicators to isolate operating problems. • COMM indicator (green) for communication • FAULT indicator (red) for hardware faults
COMM and FAULT Indicators

When the terminal starts, the fault indicator should be off, except for a few brief flashes, and the comm indicator on. If the indicators remain off, the power supply or logic module has failed. Check the power cable. If the power is not within range, replace the power supply. If the power is within range, replace the logic module. After a successful startup, both indicators are off and controlled by the application running on the terminal.

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

25

The table shows indicator states if the terminal powers on and stops during startup.

Indicator States If the Terminal Stops During Startup
Fault (Red) Indicator Comm (Green) Indicator Off Blinking On Off On(2) Blinking Description Last firmware download failed. Reload firmware using Firmware Upgrade Wizard (FUW) utility. EBC boot loader firmware failed or is missing. Reload firmware using Firmware Upgrade Wizard (FUW) utility. Windows CE OS firmware failed or is missing. Reload firmware using Firmware Upgrade Wizard (FUW) utility. Fatal hardware error occurred. Replace the logic module. Fatal hardware error in display. Replace the display module.

Blinking(1)

(1) (2)

Blinking red indicates a recoverable error. Solid red indicates a nonrecoverable or fatal error.

Check the Display
If the terminal display is dim or unreadable: • check the brightness setting of the display. From Configuration mode on the terminal, access Terminal Settings>Display Intensity. • check the Screen Saver settings. The backlight may be turning off or dimming the display unexpectedly. From Configuration mode on the terminal, access Terminal Settings>Display>Screen Saver.

Publication 2711P-IN001I-EN-P - November 2009

26

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Startup Information Messages
Startup information messages display in a specific sequence on the terminal during startup and typically display for a few seconds. These messages do not require that you perform any action.
Message # 37 30 1 31 31.5 32 2.5 Message Video Initialized Watchdog Test RAM Test Stuck Key Stuck Touch Battery Test Registry Search Description Configures and initializes the graphics video system. Tests the watchdog circuitry to verify system integrity. Tests the RAM memory. Checks the integrity of the function key hardware. Checks the integrity of the touch screen hardware. Checks the integrity of the battery hardware. Locates and loads the most recent, valid registry. Multiple copies of the registry are maintained. If power is lost during a registry update, a valid registry is available the next time power is applied to the terminal. Checks for a new OS firmware upgrade on the external CompactFlash card and the serial port. Transfers a new OS firmware upgrade from the external CompactFlash card to the terminal. Message may display for several minutes. Programs the OS firmware just downloaded into the internal flash memory. Message may display for several minutes. Checks the integrity of the OS firmware. Launches the operating system (OS). Internal file system integrity check (### is percent progress indicator). Internal file system integrity check disabled. Contact technical support.

2 50

Image Search External CF

23 24 28 29 29.1

Internal CF CRC Check Starting System System Check ### System Check

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

27

Startup Error Messages
When an error occurs, the terminal displays an error number with a text message. The word ERROR! appears under the message in different languages.
# Displayed Message ERROR! FEHLER! ERREUR! ERRORE!

Error # 1

Message RAM Test

Description RAM test failure.

Recommended Corrective Action Reset the terminal. If error persists, reseat the SO-DIMM RAM module. If error still persists, replace the logic module. Reload the firmware. If error persists, replace the internal CompactFlash card. If error still persists, replace the logic module. Reload the firmware. If error persists, replace the internal CompactFlash card. If error still persists, replace the logic module. Reload the firmware. If error persists, replace the logic module. Check that nothing is pressed against a key. Reset the terminal without key presses. If error persists, replace the display module. Check that nothing is pressed against the touch screen. Reset the terminal without pressing the touch screen. If error persists, replace the display module. Replace the battery. If error persists, replace the logic module. Upgrade the system firmware to revision 3.10.03 or later. Reload the firmware. If error persists, replace the internal CompactFlash card. If error still persists, replace the logic module. Reload the firmware. If error persists, replace the external CompactFlash card and attempt the firmware upgrade again.

23

Internal CF

Error programming the new OS firmware to internal CompactFlash card. Checksum of the OS firmware failed. Watchdog test failure. Function key failure.

24

CRC Check

30 31

Watchdog Test Stuck Key

31.5

Stuck Touch

Touch screen failure.

32 33.5 40

Battery Test NVRAM Access EXE Check

Battery failure. Nonvolatile memory failure. System OS firmware is missing or corrupt. Error loading the OS firmware from the external CompactFlash card.

50

External CF

Publication 2711P-IN001I-EN-P - November 2009

28

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Specifications
PanelView Plus Terminals - 2711P-Kxxxx, 2711P-Txxxx, 2711P-Bxxxx, 2711P-RDxxxx, 2711PC-Txxxx
Attribute Display Display type Display size 700 1000 1250 1500 Display area (WxH) 700 1000 1250 1500 Display resolution 700 1000 1250 1500 Luminance Touch screen Electrical Input voltage, DC Power consumption, DC Input voltage, AC Power consumption, AC PCI slot max. available power Supply, DC Supply, AC
(1)

Value Color active matrix, thin film transistor (TFT), liquid crystal display (LCD) 6.5 in. 10.4 in. 12.1 in. 15 in. 132 x 99 mm (5.2 x 3.9 in.) 211 x 158 mm (8.3 x 6.2 in.) 246 x 184 mm (9.7 in x 7.2 in.) 304 x 228 mm (12.0 x 9.0 in.) 640 x 480 640 x 480 800 x 600 1024 x 768 300 cd/m2 Nits Analog resistive 24V DC nom (18… 32V DC) 70 W max (2.9 A @ 24V DC) 39 W typical (1.6 A @ 24V DC) 85… 264V AC (47…63 Hz) 160 VA max (65 VA typical) 11 W 5W

Dimensions, Approx., (HxWxD) for based configured unit without communication module 700 keypad, or keypad and touch 700 touch 1000 keypad, or keypad and touch 1000 touch 1250 keypad, or keypad and touch 1250 touch 1500 keypad, or keypad and touch 1500 touch
(1)

193 x 290 x 55 mm (7.58 x 11.40 x 2.18 in.) 179 x 246 x 55 mm (7.04 x 9.68 x 2.18 in.) 248 x 399 x 55 mm (9.77 x 15.72 x 2.18 in.) 248 x 329 x 55 mm (9.77 x 12.97 x 2.18 in.) 282 x 416 x 55 mm (11.12 x 16.36 x 2.18 in.) 282 x 363 x 55 mm (11.12 x 14.30 x 2.18 in.) 330 x 469 x 65 mm (12.97 x 18.46 x 2.55 in.) 330 x 416 x 65 mm ((12.97 x 16.37 x 2.55 in.)

The PCI slot does not apply to the PanelView Plus Compact 1000 terminal.

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

29

PanelView Plus Terminals - 2711P-Kxxxx, 2711P-Txxxx, 2711P-Bxxxx, 2711P-RDxxxx, 2711PC-Txxxx
Weight, Approx. for base configured unit without communication module 700 keypad, or keypad and touch 700 touch 1000 keypad, or keypad and touch 1000 touch 1250 keypad, or keypad and touch 1250 touch 1500 keypad, or keypad and touch 1500 touch General Battery life Clock Status indicators Application flash memory 700 to 1500 series D or earlier logic modules 2711P-RW1 2711P-RW2 2711P-RW3 700 to 1500 series E or later logic modules 2711P-RW6 2711P-RW7 2711P-RW8 External CompactFlash storage 4 years min. at 25 °C (77 °F) Battery-backed, + /- 2 minutes per month COMM (green), Fault (red) 1.9 kg (4.2 lb) 1.7 kg (3.8 lb) 2.9 kg (6.3 lb) 2.6 kg (5.7 lb) 3.4 kg (7.6 lb) 3.2 kg (7.1 lb) 4.6 kg (10.0 lb) 4.2 kg (9.3 lb)

26 MB 72 MB 95 MB 80 MB 203 MB 446 MB 512 MB max

Environmental Specifications
Specification Temperature, operating Temperature, nonoperating Vibration Shock, operating Shock, nonoperating Relative humidity Enclosure ratings Airborne Contaminants Value 0…55 °C (32…131 °F) -20…70 °C (-13…158 °F) 10… 57 Hz, 0.012 pk-pk displacement 57…500 Hz 2.0 g pk acceleration 15 g at 11 ms 30 g at 11 ms 5…95% without condensation NEMA Type 12, 13, 4X (indoor use only), IP54, IP65 ANSI/ISA S71.04-1985 Severity Level G3 EN60654-4:1998 Class 3

Publication 2711P-IN001I-EN-P - November 2009

30

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

Certifications
Certification (1) c-UL-us UL Listed Industrial Control Equipment, certified for use in US and Canada. See File E10314. UL Listed Industrial Control Equipment for use in: • Class I, Div 2, Group A, B, C, D • Class II, Div 2 Groups F, G • Class III Hazardous Locations European Union 89/336/EEC EMC Directive, compliant with: EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers Australian Radiocommunications Act, compliant with: AS/NZS CISPR 11; Industrial Emissions Products identified with the suffix M in the catalog number, are certified to the requirements of one or more marine societies.

CE (EMC)

CE (LVD) C-Tick Marine
(1)

See the Product Certification link on http://www.ab.com for declarations of conformity, certificates, and other certification details.

Additional Resources
For additional information on the terminals, refer to these publications.
Resource PanelView Plus User Manual, publication 2711P-UM001 Wiring and Grounding Applications for PanelView Plus devices Technical Data, publication 2711P-TD001 PanelView Plus Compact Terminals User Manual, publication 2711PC-UM001 Description Provides an overview of the PanelView Plus and PanelView Plus CE terminals and gives information on how to install, operate, configure, and troubleshoot these devices. Provides additional information on wiring and grounding the PanelView Plus and PanelView Plus CE terminals. Provides an overview of the PanelView Plus Compact terminals and gives information on how to install, operate, configure, and troubleshoot these devices.

You can view or download publications and translated versions of the installation instructions at http://literature.rockwellautomation.com. To order paper copies of technical documentation, contact your local Rockwell Automation distributor or sales representative.

Publication 2711P-IN001I-EN-P - November 2009

PanelView Plus 700 to 1500 and PanelView Plus Compact 1000 Terminals and Display Modules

31

Publication 2711P-IN001I-EN-P - November 2009

Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using its products. At http://support.rockwellautomation.com, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools. For an additional level of technical phone support for installation, configuration and troubleshooting, we offer TechConnect support programs. For more information, contact your local distributor or Rockwell Automation representative, or visit http://support.rockwellautomation.com.

Installation Assistance
If you experience a problem within the first 24 hours of installation, please review the information that's contained in this manual. You can also contact a special Customer Support number for initial help in getting your product up and running. United States Outside United States 1.440.646.3434 Monday – Friday, 8 a.m. – 5 p.m. EST Please contact your local Rockwell Automation representative for any technical support issues.

New Product Satisfaction Return
Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures. United States Contact your distributor. You must provide a Customer Support case number (see phone number above to obtain one) to your distributor to complete the return process. Please contact your local Rockwell Automation representative for the return procedure.

Outside United States

Allen-Bradley, Rockwell Automation, FactoryTalk View, PanelView, PanelView Plus, and TechConnect are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 2711P-IN001I-EN-P - November 2009
Supersedes Publication 2711P-IN001H-EN-P - March 2009 Copyright © 2009 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

Similar Documents

Premium Essay

Chapter 12 Cis 345

...click Control Panel, and then click System and Security; under Administrative Tools click the Event Viewer. For this exercise, you need a computer running Windows. Ideally, it should be a computer that has been used for a while, so that the event log contains several entries. It need not be connected to a network. However, you must be logged on to the computer as a user with administrator-equivalent privileges. 1. Click Start, then click Control Panel. The Control Panel window appears. 2. In the Control Panel window, click System and Security. The System and Security window appears. 3. If the entire list of options doesn’t appear, scroll to the bottom of the window and click View event logs under the Administrative Tools heading. 4. A User Account Control window appears, requesting your permission to continue. Click Continue. 1. The Event Viewer window appears, with three columns of panes. The center pane lists a summary of administrative events. Notice that events are classified into the following types: Critical, Error, Warning, Information, Audit Success, and Audit Failure. The number of events that have been logged in each category are listed to the right of the classification entry. How many Error events has your Windows workstation logged in the last 24 hours? 410 errors In the last 7 days? 440 errors 2. If your workstation has logged any errors in the past 7 days, click the plus sign next to the...

Words: 1193 - Pages: 5

Premium Essay

Domains

...Active Directory Group Policy Objects (GPO) are a boon to all Windows Active Directory administrators for managing Active Directory Users, computers and groups easily and quickly. But with only the native AD tools, PowerShell, etc. administrators have to spend quite an amount of time in managing the Group Policy Objects. ADManager Plus is a web-based Active Directory Management and Reporting software that helps administrators in managing the Group Policy objects of multiple domains, with just mouse-clicks and UI based actions. This software also provide pre-built Group Policy (GPO) Reports to fetch Group Policy related information swiftly. This Active Directory management tool also helps in Microsoft Exchange Server Management and Reporting. With ADMnager Plus, in just a single click, administrators can: * Enable/Disable multiple Group Policies * Mass manage GPO links: Enable/Disable GPO Links, Add/Remove GPO Links * Enforce multiple GPOs / Make them Unenforced * Block or Unblock GPO Inheritance for any Domain/Organizational Unit (OU) Further, administrators can also get to know instantly, * The status of all the GPOs available in a Domain * All the Domains/Organizational Units (OU)/Sites that a GPO is linked to * All the GPOs that are linked to any specific Domain/OU/Site Enable GPOs / Disable GPOs With this feature, administrators can enable or disable all the required GPOs in any domain, in one single action instantly. Further, if needed, administrators...

Words: 2762 - Pages: 12

Premium Essay

Hot Tamales Research Paper

...Hot tamales and the Delta have a long-lived history packed with punches and flavors true to each person who puts it all into this Delta delicacy. So much so, we celebrate each year at the Delta Hot Tamale Festival in Greenville, Mississippi. A weekend full of everything a good festival encompasses, a good time, good tunes and good people but also brings you —arguably— some of the best hot tamales in the world and an enrapturing line up of authors and chefs providing lively panel discussions and even better food. This year the Delta’s own Chef Cole Ellis of Delta Meat Market in Cleveland will provide dinner alongside Slade Rushing, the James Beard nominated chef at Brennan’s in New Orleans; James Beard award winner Stephen Stryjewski—plus...

Words: 260 - Pages: 2

Premium Essay

Technical

...There are many authentication mechanisms used to authenticate a user before accessing a restricted resource or place such as password s, personal identification numbers (PINs) fingerprints. This system uses a person’s identification card to either grant or deny access to the dormitory. Authorizations are structured in this system in such a manner that only users whose identification numbers appears in the database of the dormitory members control list are granted access and the rest denied. The system comprises of three major parts; control panel (highly reliable processor), electronic proximity reader and a security camera system. The electronic proximity reader reads data from the user’s identification card inputs it into the control panel where it is verified against the database of access control list (Conference & Khosrowpour, 2001). The security camera records users at the entrance and sends the data to the control panel where the records are kept...

Words: 979 - Pages: 4

Free Essay

Kinds Monitor Hardware

...Introduction The Computers in our world now are very good and faster. Users are very fast to learn how to use the computer. In modern world computer is a part of our life because computer is our need to do our work. Computer has a part like, the brain or CPU, mouse, keyboard, speaker, printer, AVR and monitor. Monitors in this year are modern it upgrade like computer. Brief history of a monitor The video display terminal, or VDT, marked the early days of computer monitors. These VDTs included a screen and attached keyboard linked to a larger computer by a serial connection. Because VDTs required a connection to a larger computer, they were often referred to as "dumb terminals." Dumb terminals displayed text only in two colors, usually black and green. The Apple II and first game machines began using a television CRT. IBM's CRT The ssssst of its new PS/2 computer system. The display technology allowed for 256 different colors and 640 x 480 resolutions. Despite the appearance of newer display techniques, VGA has become a computer monitor standard. Indeed, the VGA may have become the impetus for the modern computer gaming industry as the increased color palette made graphics possible. Up to this point, computer displays were limited to text. RESEARCH Types of Monitors A cathode ray tube or CRT CRT technology, computer monitors continue to be referred to as "The Tube". A CRT works by moving an electron beam back and forth across the back of the screen. Each time the...

Words: 4169 - Pages: 17

Free Essay

Contract Termination

...the pendency of any dispute, while giving the contractor the right to make a claim for a price increase. Rarely does anything but nonpayment justify termination by a contractor. The greatest risk of the contractor in terminating a contract is that the termination could be determined by a court or arbitration panel to be wrongful. If the termination is proved to be wrongful, then C terminating the contract not only fails to collect its additional funds spent to complete the project, but must also pay A its contract payments through the date of termination and potentially the loss of profit on the work not performed. 2. Termination for convenience clauses are intended to provide the owner with the option to terminate the remaining balance of the contracted for work for a reason other than the contractor’s default. The owner can terminate the balance of the work for convenience as long as there is a termination for convenience clause in the contract. However, if the contract does not contain a termination for convenience clause, and the owner terminates the contract before the work is complete, then the contractor would be entitled to the value of the work completed plus profit that he or she would have earned on the balance of the contract. The subcontractor will be entitled to recover the net benefit conferred on the prime...

Words: 690 - Pages: 3

Free Essay

Halo

...Welcome to ASUS WebStorage, your personal cloud space Our function panel will help you better understand ASUS WebStorage services. The panel and a series of function instructions will guide you to explore the unprecedented cloud experiences.. All ASUS WebStorage functions at one glance Entering the world of ASUS You are going to find how the thoughtfully designed function panel of ASUS WebStorage provides a range of WebStorage functions that completely do without the complexity of application software, and you cannot wait to try these intuitive functions. Help wizard Search: Rapidly find the data stored in cloud. Upgrade: Package upgrade or space enlarging Referral: Invite your friends and get extra space Support: FAQ helps find the answers you need. Forum: Understand the issues facing others and their solutions. Setup: Rapidly set up your language, upload speed, and proxy. Frequently used functions You are able to drag your frequently used functions to the upper area of the control panel, and drag various applications to the right or left in the lower area. When you log into the control panel for the first time, we will step by step walk you through every function for you to easily hover on cloud. You are going to be familiar with it in just three minutes. Cloud is not far away thanks to easy and intuitive function setup ASUS WebStorage provides data backup, file sharing, and synchronization across multiple devices, such as cell phones, desktops, and laptops...

Words: 944 - Pages: 4

Free Essay

Cs4 Term Paper

...InDesign CS4 FOR ® DUMmIES by Galen Gruman ‰ InDesign CS4 FOR ® DUMmIES by Galen Gruman ‰ InDesign® CS4 For Dummies® Published by Wiley Publishing, Inc. 111 River Street Hoboken, NJ 07030-5774 www.wiley.com Copyright © 2009 by Wiley Publishing, Inc., Indianapolis, Indiana Published by Wiley Publishing, Inc., Indianapolis, Indiana Published simultaneously in Canada No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, scanning or otherwise, except as permitted under Sections 107 or 108 of the 1976 United States Copyright Act, without either the prior written permission of the Publisher, or authorization through payment of the appropriate per-copy fee to the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, (978) 750-8400, fax (978) 646-8600. Requests to the Publisher for permission should be addressed to the Legal Department, Wiley Publishing, Inc., 10475 Crosspoint Blvd., Indianapolis, IN 46256, (317) 572-3447, fax (317) 572-4355, or online at http://www.wiley.com/go/permissions. Trademarks: Wiley, the Wiley Publishing logo, For Dummies, the Dummies Man logo, A Reference for the Rest of Us!, The Dummies Way, Dummies Daily, The Fun and Easy Way, Dummies.com, Making Everything Easier, and related trade dress are trademarks or registered trademarks of John Wiley & Sons, Inc. and/ or its affiliates in the United States...

Words: 11685 - Pages: 47

Free Essay

Issues Facing Today's Organizations

...Issues Facing Today’s Organizations Jessica Kemske June 3, 2012 Organizations today face many different challenges. Some challenges are based on the nature of operations and some challenges are more common and are faced by most organizations. A couple of the more common challenges would be technological advances and societal views. In my opinion, technological advances are the biggest issue that organizations face today. If we look back even just ten years ago we have come such a long way with technology. Now someone could just pick up an iPad and have a face to face conference with someone on the other side of the world. Most companies, 20 years ago, didn’t even have websites, nowadays that would be considered appalling. Going back twenty years companies were just developing email. Now just about everyone in an organization must have their own computer or at least have access to one. Twenty plus years ago there was no need for such a large information technology department or computer specialists; now there is a high demand. This demand has required companies to either create or hire an outside entity to provide them with “tech-support.” This requirement costs incredibly large sums of money. Companies have to keep up with modern technology in order to offer services that are compatible with societal needs. One of the technological issues is the lifespan of the equipment. Companies must be able to reinvest and keep up with current technology. This can cause a problem...

Words: 1267 - Pages: 6

Free Essay

Djehd

...Welcome to ASUS WebStorage, your personal cloud space Our function panel will help you better understand ASUS WebStorage services. The panel and a series of function instructions will guide you to explore the unprecedented cloud experiences.. All ASUS WebStorage functions at one glance Entering the world of ASUS You are going to find how the thoughtfully designed function panel of ASUS WebStorage provides a range of WebStorage functions that completely do without the complexity of application software, and you cannot wait to try these intuitive functions. Help wizard Search: Rapidly find the data stored in cloud. Upgrade: Package upgrade or space enlarging Referral: Invite your friends and get extra space Support: FAQ helps find the answers you need. Forum: Understand the issues facing others and their solutions. Setup: Rapidly set up your language, upload speed, and proxy. Frequently used functions You are able to drag your frequently used functions to the upper area of the control panel, and drag various applications to the right or left in the lower area. When you log into the control panel for the first time, we will step by step walk you through every function for you to easily hover on cloud. You are going to be familiar with it in just three minutes. Cloud is not far away thanks to easy and intuitive function setup ASUS WebStorage provides data backup, file sharing, and synchronization across multiple devices, such as cell phones, desktops...

Words: 944 - Pages: 4

Free Essay

Wind Farms

...ABB Inc Substation Division 940 Main Campus Dr, Suite 400 Raleigh NC 27606 09/29/2011 TRKPSS0000489 Email 09/13/2011 Mr. Shannon Thomson Canadian Hills Wind Farm – 34.5/345 kV Collector Substation – Control & Protection Panels Referring to the oneline drawings obtained and further discussions for the above mentioned project, we are pleased to submit our offer as follows. Our offer is based on our interpretation of drawings provided. A. Price Schedule B. Commercial conditions C. Bills of material, Divisions of work & responsibility D. Technical comments E. Documentation We hope the above is to your satisfaction. Please do not hesitate to contact us if you need anything clarified. Best Regards, Amer Alhalig Proposals Engineer Substation Automation, Power Systems Phone: +1 919-807-5792 Email – amer.alhalig@us.abb.com Attachments Panel layout drawings Data sheets DOW/DOR Price schedule SAS price schedule Total Line, Xfmr, Bus, 3 Feeder, Cap bank, Metering, $470,000 USD and RTU Panels, Engineering, and Coordination Studies Prices are valid for the total quantity, specs and services as quoted. Any changes in the list of activities, responsibilities, hardware or scope will necessitate re-pricing. Price is FOB Calumet, Oklahoma...

Words: 5949 - Pages: 24

Premium Essay

Nec Case

...Keiretsu Membership, Firm Size, and Corporate Returns on Value and Cost∗ Xueping Wu† , Piet Sercu‡ and Charles Chen§ First draft: November 1998; this version: October 2000 ∗ Jun Yao and Shu-Chuen Chong provided helpful research assistance. The authors thank Kathryn Dewenter, Amar Gande, Larry Goldberg, Ser-Huang Poon, Kazunori Suzuki, and other participants at the 1999 WFA and 2000 EFA Conferences and workshops at HKUST, K.U.Leuven, and Strathclyde; and Yasushi Hamao, Nancy Huyghebaert, Shuhe Li, Xijia Su, Linda Van de Gucht, and Cynthia Van Hulle for useful discussions or comments that have substantially improved content as well as presentation. All remaining errors are the authors’. † City University of Hong Kong, Department of Economics and Finance, Tat Chee Avenue, Kowloon, Hong Kong. Tel: (852) 2788 7577; Fax: (852) 2788 8806; email: efxpwu@cityu.edu.hk. ‡ (Corresponding author) KU Leuven, Graduate School of Business Studies, Naamsestraat 69, B3000 Leuven; Tel: +32 16 32 6756; Fax: +32 16 32 6620; email: piet.sercu@econ.kuleuven.ac.be. § Department of Accountancy, City University of Hong Kong; Tel: (852) 2788 7909; Fax: (852) 2788 7002; email: accpj@cityu.edu.hk. Abstract We test how keiretsu membership affects the Fama and French (1999) required IRR on value (or cost of capital) and the IRR on cost (or return on investment), 1974-95, of all listed non-financials in Japan. Rather than computing point estimates from aggregate data, we employ...

Words: 19106 - Pages: 77

Free Essay

About Life

...Tutorial Tutorial Overview Welcome to NetCracker’s Tutorial. This seven-part tutorial is designed to: • introduce you to NetCracker Designer’s functionality, • familiarize you with the Graphical User Interface (GUI), • provide you with step-by-step instructions so you can create network designs. This tutorial uses four sample project files, which are included with your NetCracker Designer Software. While you can start at any point, it is recommended that you begin with Lesson 1. You will learn how to: ▪ Use the NetCracker Designer software ▪ Work with an existing NetCracker Designer file ▪ Create a NetCracker Designer project ▪ Use animation features ▪ Use network simulation and statistics ▪ Create multi-leveled network designs ▪ Discover existing networks ▪ Use advanced features ▪ Conduct a database search ▪ Use the Device Factory Wizard Tutorial Lessons Tutorial 2 Overview 2 Tutorial Lessons 2 Lesson 1 -- Introduction To NetCracker Designer 3 Lesson 2 -- Using Animation Features 11 Lesson 3 -- Creating a New NetCracker Designer Project 16 Lesson 4 -- Creating Multi-level Network Designs 23 Lesson 5 – Customizing the Database and Database Search 29 Lesson 6 -- How to Use AutoDiscovery 37 Conclusion 42 Lesson 1 -- Introduction To NetCracker Designer This section is designed to: • introduce you to the Graphical User Interface(GUI), • identify each of the elements...

Words: 9909 - Pages: 40

Free Essay

Morality

...tolerated these segregated communities behaving in ways, which run counter to our values.” A genuinely liberal country “believes in certain values and actively promotes them“, Mr Cameron said. “Freedom of speech, freedom of worship, democracy, the rule of law, equal rights, regardless of race, sex or sexuality. “It says to its citizens: This is what defines us as a society. To belong here is to believe in these things.” He said that under the “doctrine of state multiculturalism”, different cultures have been encouraged to live separate lives, and he argued that the UK needs a stronger national identity. The Moral Maze called witnesses to put their points of view for and against the UK experience of state multiculturalism, and much of the ensuing polemic centred on the simultaneously conflicting aspects of fairness. The panel had difficulty with the ethical paradox of equality — fairness for all — and equity — fairness for each — being of equal validity at the same time. The human right to self-determination —...

Words: 757 - Pages: 4

Free Essay

The Paper

...OPERATIONS ORDER | primary client NAVISION #: 100725 | |CLIENT: Albert Einstein College of Medicine |CONTACT: Melanie Brown | |1300 Morris Park Ave |Assistant Administrator | |Bronx, NY 10461 |718-430-4152 | | |Email: Melanie.brown@einstein.yu.edu | |SECONDARY CLIENT #: (Location & Contact) | |NAVISION #: 151776 | |1300 Morris Park Ave | |Bronx, NY 10461 | | ...

Words: 4459 - Pages: 18