Programmable Logic Controllers: Programming Methods and Applications by John R. Hackworth and Frederick D. Hackworth, Jr. Table of Contents Chapter 1 - Ladder Diagram Fundamentals Chapter 2 - The Programmable Logic Controller Chapter 3 - Fundamental PLC Programming Chapter 4 - Advanced Programming Techniques Chapter 5 - Mnemonic Programming Code Chapter 6 - Wiring Techniques Chapter 7 - Analog I/O Chapter 8 - Discrete Position Sensors Chapter 9 - Encoders, Transducers, and Advanced
Words: 73061 - Pages: 293
Document Type: Prentice Hall Author: John G. Proakis and Masoud Salehi Book: Communication Systems Engineering Copyright: 2002 ISBN: 0-13-061793-8 NI Supported: No Publish Date: Sep 6, 2006 Multicarrier Modulation and OFDM Overview This tutorial is part of the National Instruments Signal Generator Tutorial series. Each tutorial in this series, will teach you a specific topic of common measurement applications, by explaining the theory and giving practical examples. This tutorial covers
Words: 2381 - Pages: 10
HUB Networks using a Star topology require a central point for the devices to connect. Originally this device was called a concentrator since it consolidated the cable runs from all network devices. The basic form of concentrator is the hub. As shown in Figure; the hub is a hardware device that contains multiple, independent ports that match the cable type of the network. Most common hubs interconnect Category 3 or 5 twisted-pair cable with RJ-45 ends, although Coax BNC and Fiber Optic BNC hubs
Words: 3676 - Pages: 15
******Created by ebook converter - www.ebook-converter.com****** ******ebook converter DEMO - www.ebook-converter.com******* ******Created by ebook converter - www.ebook-converter.com****** KOINONIA HOUSE Coeur d’Alene, Idaho 83816-0347 ******ebook converter DEMO - www.ebook-converter.com******* ******Created by ebook converter - www.ebook-converter.com****** COSMIC CODES Copyright © 1999 by Koinonia House Revised 2004 P.O. Box D Coeur d’Alene, ID 83816-0347 Web Site: http://www
Words: 141008 - Pages: 565
Relion® 615 series Transformer Protection and Control RET615 Product Guide Transformer Protection and Control RET615 Product version: 5.0 1MRS756891 H Contents 1. Description.....................................................................3 16. Inputs and outputs......................................................21 2. Standard configurations.................................................3 17. Station communication...............................................
Words: 11206 - Pages: 45
Chapter 01 1.1 Introduction: A storage device may be used to store energy from renewable energy source in DC form which can be converted to AC power by using power inverter. Pulse Width Modulated (PWM) technique may be used to control output rms voltage of the inverter. As the load is variable, the power consumed by the load (PL) may be smaller than the power generated from the renewable energy source (PR). Therefore a Flexible AC Transmission System (FACTS) Controller may be
Words: 12772 - Pages: 52
UNIVERSITY OF KERALA B. TECH DEGREE COURSE 2008 SCHEME ELECTRICAL AND ELECTRONICS ENGINEERING I to VIII SEMESTER SCHEME AND SYLLABUS BOARD OF STUDIES IN ENGINEERING AND FACULTY OF ENGINEERING AND TECHNOLOGY UNIVERSITY OF KERALA B.Tech Degree Course – 2008 Scheme REGULATIONS 1. Conditions for Admission Candidates for admission to the B.Tech degree course shall be required to have passed the Higher Secondary Examination, Kerala or 12th Standard V.H.S.E., C.B.S.E., I.S.C. or any examination
Words: 36386 - Pages: 146
******************** ********************************** Term Paper On discipline “Microprocessor Systems” Done by ***** Student of ******** Checked by ********* Task Design MP System, based on single-chip 8-bit microprocessor KR580VM80AOA with the following characteristics: 1. CPU: KR580VM80A0A. 2. RAM: 24 KBytes 3. ROM: 40 KBytes 4. Controlling for parity. 5. Number of digital inputs: 8. 6. Number of digital outputs: 8. 7. Interrupt controller, with a fixed
Words: 3184 - Pages: 13
Automation is the use of control systems and information technologies to reduce the need for human work in the production of goods and services. In the scope of industrialization, automation is a step beyond mechanization. Whereas mechanization provided human operators with machinery to assist them with the muscular requirements of work, automation greatly decreases the need for human sensory and mental requirements as well. Automation plays an increasingly important role in the world economy and
Words: 7787 - Pages: 32
CHAPTER 1 INTRODUCTION TO INFORMATION TECHNOLOGY 1.1 Introduction Modern civilization has become so complicated and sophisticated that to survive one has to be competitive. This compels people to keep themselves informed of all types of happening in the society. And this in turn entails the need for an infrastructure of information. This is the point where information technology or IT becomes most important, as it is the infrastructure that allows us to get information accurately and in time. Before
Words: 12773 - Pages: 52
