“Heaven’s Light is Our Guide”
[pic]

DEPARTMENT OF Electronics and Telecommunication Engineering Rajshahi University of Engineering & Technology, Bangladesh

RADIO RESOURCE MANAGEMENT IN WiMAX

Author Md.Masud Hasan Roll No.054005 Department of Electronics and Telecommunication Engineering
Rajshahi University of Engineering & Technology

Supervised by Md.Delwar Hossain Head Department of Electronics and Telecommunication Engineering Rajshahi University of Engineering & Technology

ACKNOWLEDGEMENT

All praises to ALLAH, the cherisher and the sustainer of the universe, the most gracious and the most merciful, who bestowed me with health and abilities to complete this thesis successfully.

This thesis means to me far more than a honours degree requirement as my knowledge was significantly enhanced during the course of its research and implementation. I am especially thankful to the Faculty and Staff of Rajshahi University of Engineering and Technology (RUET), Rajshahi, Bangladesh, that have always been a source of motivation for me and supported me tremendously during this thesis.

I am extremely grateful to my thesis supervisor ‘Md.Delwar Hossain’ who guided me in the best possible way in my thesis. He is always a source of inspiration for me. His encouragement and support never faltered.

I am enormous grateful to Noman Shabbir & Hasnain Kashif whose work on this field was the base of my thesis.

I am also very thankful to all those course mates who have helped me morally as well as academically. In every hour of need, their full cooperation was there for me.

I special gratitude and acknowledgments are there for my parents for their everlasting moral support and encouragement.

April 2010 Md.Masud Hasan

RUET,Rajshahi.

“Heaven’s Light is Our Guide”
[pic]

Department of Electronics and Telecommunication

Engineering

Rajshahi University of Engineering & Technology, Bangladesh
CERTIFICATE
This is certify that the thesis on “Radio Resource Management in WiMAX”
By

Md Masud Hasan
Roll No. 054005

Has been carried out under my supervision.

------------------------------------------
Md. Delwar Hossain
Head
Department of Electronics and Telecommunication Engineering.
Rajshahi University of Engineering &Technology.
Rajshahi-6204
April -2010
RUET, Rajshahi.

ABSTRACT

This thesis is related with the WiMAX(Worldwide Interoperatibility for Microwave Access) technology.Today, different types of cellular networks are actively working on the radio links. For instance, the Global System for Mobile Communication (GSM) is being used in nearly all of the countries of the world and currently it has around three billion users all over the world. Universal Mobile Telecommunication System (UMTS) is currently deployed in many countries and it is providing increased data rates, coverage and mobility as compared to GSM. Wireless Local Area Networks (WLAN) are very famous when we have a small area and none real time services. Worldwide Interoperability for Microwave Access (WiMAX) is a new technology and it is in deployment phase. In all these cellular technologies, we have very limited resources and we have to make best use of them by proper management. Radio Resource Management (RRM) is a control mechanism for the overall system which is being used to manage radio resources in the air interface inside a cellular network. The main objective is to utilize the available spectral resources as efficiently as possible. Our aim is to use them in the best possible way to maximize the performance and spectral efficiency in such a way that we have maximum number of users in our network and Quality of Service (QoS) is up to the mark. In a cellular communication system, a service area or a geographical region is divided into a number of cells and each cell is served by an infrastructure element called the base station which works through a radio interface. The frequency license fees, real estate, distribution network and maintenance are the issues which dominates the cost for deploying a cellular network. In RRM, we control parameters like Radio Frequency (RF) planning, link budgeting, modulation schemes, channel access schemes etc. RF planning includes cell planning, coverage of the network and capacity of the network. Our main focus in this thesis will be on cell planning and link budgeting and we will discuss them in context of a WiMAX network.

CONTENTS

Acknowledgement…………………………………………………….……………….….ii
Certificate………………………………………………………………………................iii
Abstract……………………………………………………………………………….......iv
List of Figures………………………………………………………………………….…ix
List of Tables…..……………………………..…………………………………………..xi CHAPTER 1
1 Introduction ……………………………………………………………………....12 Outline of Thesis and Contribution ………………………………………………13 CHAPTER 2
2 WiMAX.. 15 2.1 WiMAX Standarads 15
2.2 Introduction 16
2.3 Overview of Technical Information………………………………………….…..17 2.3.1 WiMAX Physical Layer…………………………………………………….…18 2.3.2 OFDM Basics...……..………………………………………………………….18 2.3.3 WiMAX OFDM Parameters……………………………………...……..….....21 2.3.4 WiMAX MAC Layer 22 2.3.5 Channel Access Mechanisms 24 2.3.6 QoS in WiMAX 24 2.3.7 WiMAX Mobility Support 26 2.3.8 Multicast and Broadcast Services 27
2.4 WiMAX Features for Performance Enhancement 27 2.4.1 Advanced Antenna Systems 27 2.4.2 Hybrid ARQ 28
2.5 WiMAX Network Architecture 28 CHAPTER 3 Radio Resource Management With Formal Technology 30 Introduction………………………………………………………………………30
3.1 Frequency Band Allocation 31
3.2 UMTS/HSDPA/HSUPA frequency bands deployment……………………………32

3.3 Cell Planning 32 3.3.1 Cell Site………………………………………………………………………..34 3.3.2 Fquency Reuse 34 3.3.3 Types of Cells 35
3.4 Link Budget 37 3.4.1 Calculation of Link Budget 37
3.5 Call Admission Control 39 3.5.1 Handover 39 3.5.2 Types of Handover 40
3.6 Modulation Schemes 41 3.6.1 Analog Modulation 41 3.6.2 Digital Modulation 42 3.6.3 Spread-spectrum techniques……...………………………...…………………….42

3.6.4 Analog-over-analog methods…………………………………………................42

3.6.5 Analog-over-digital methods…………………………………………………….43

3.7 Multiple Access Techniques 43 3.7.1 Frequency Division Multiple Access (FDMA) 43 3.7.2 Time Division Multiple Access (TDMA) 43 3.7.3 Code Division Multiple Access (CDMA) 44 3.7.4 Orthognal Frequency Division Multiple Access (OFDMA) 44

CHAPTER 4
4 Radio Resource Management in WiMAX 45
4.1 Frequency Band Allocation in WiMAX 45
4.2 Cell Planning in WiMAX 47 4.2.1 Technical Cell Site Issues for WiMAX 48 4.2.2 WiMAX Network Plannings 48
4.3 Link Budget for WiMAX 49 4.3.1 Signal availability test…………….…………………………………………..…52
4.4 Call Admission Control in WiMAX 53 4.4.1 Handover in WiMAX 54
4.5 Modulation Schemes in WiMAX 54 4.5.1 Binary Phase Shift Keying 56 4.5.2 Quadrature Phase Shift Keying 56 4.5.3 Quadrature Amplitude Modulation 56
CHAPTER 5
5 Simulation 57
5.1 Link Budget 57
5.2 Cell Planning 61 5.2.1 Cell Coverage 61 5.2.1.1 SUI model………………………………………………………………….…62 5.2.1.2 Ericsson model……………………………………………………………….65 5.2.1.3 Okumura model………………………………………………………………67 5.2.2 Nominal Cell Site 68 5.2.3 Site Survey 71
CHAPTER 6
6 Conclusions………………………………………………………………………72
6.1 Conclusions .72
6.2 Future Works .73 Appendices…………………………………………………………………………..…74 Abbreviations and Acronyms ..74 References…...………………………………………………………………….………77 MATLAB programs for simulation………………………………………………….….81

LIST OF FIGURES

1.1 IEEE and ETSI standards for wireless networks 13
2.1 Frequency Division Multiplexing………………………………………………...19
2.2 Orthogonal Frequency Division Multiplexing……………………………………19
2.3 Orthogonal Frequency Division Multiple Access(sub-carriers)…………………..19
2.4 Uplink subchannelization in WiMAX(OFDM and OFDMA)………………...…19
2.5 OFDM symbol and subcarrier structure in WiMAX……………………………..20
2.6 OFDMA symbol and subcarriers(subchannels) structure in WiMAX……...……20
2.7 (a)Transmitter and (b)Receiver RF chains in WiMAX……………………...…….20
2.8 Examples of various MAC PDU frames 23
2.9 Over the air latency in a WiMAX network 25
2.10 WiMAX architecture 29
3.1 Different regions in the world 31
3.2 General architecture of cellular System 33
3.3 Hexagonal cells 34
3.4 Cell site ………………………………………………………………………….35
3.5 Frequency Reuse of 1/4 35
3.6 Umbrella cell 36
3.7 Link budget 38
3.8 Comparison of FDMA, TDMA and CDMA 44
4.1 Frequency bands Used for WiMAX 46
4.2 Link budget calculator…………………………………………………………....52
4.3 Adaptive modulation scheme in a cell 55
4.4 BPSK constellation diagram…. 56
4.5 QPSK constellation diagram 56
5.1 Flow chart for link budget 58
5.2 Output signals for link budget analysis in communication networks. 59
5.3 Path loss given by SUI propagation model for 2500 MHz 64
5.4 Path loss given by SUI propagation model for 3500 MHz 65
5.5 Path loss given by Ericsson propagation model for 2500 MHz 66
5.6 Path loss given by Ericsson propagation model for 3500 MHz 66
5.7 Median attenuation factor and area gain 67
5.8 Path loss given by Okumura model 68
5.9 Geographical map of Rajshahi (Bangladesh) 69
5.10 Nominal Cell Planning of Rajshahi City 70

LIST OF TABLES

2.1 Different types of services provided by fixed and mobile WiMAX 16
2.2 Frequency bands and duplexing techniques for fixed and Mobile WiMAX 17
2.3 Different parameters in WiMAX………………………………………………....21
2.4 Service class and applications 25
4.1 Frequency bands for WiMAX 47
4.2 System parameters for mobile WiMAX 49
4.3 OFDMA parameters for mobile WiMAX 50
4.4 Propagation model for mobile WiMAX 51
4.5 Link budget for mobile WiMAX 51
4.6 Signal availability test output………………………………………………….….53
5.1 Different enviorments and path loss exponent 61
5.2 Different terrains and parameters 62
5.3 Propagation models and their path loss 71 CHAPTER 1 INTRODUCTION

In the beginning of this new millennium we are having a new world which is the world of telecommunication. Telecommunication includes all the communication of computer networks, public telephone networks, radio networks, television networks and internet.

Most of the communication networks used today are wireless in nature. Wireless means transferring the signals without wires using radio waves, infra red etc.. The demand of wireless is increasing very fast as everybody wants to use the broadband services anywhere and anytime. The standardization of these wireless networks is also very important. The IEEE has developed many standards for different wireless networks. Most common IEEE standards are IEEE 802.11 for WLAN, 802.15 for Bluetooth etc as shown in Figure 1.1 [2].

One of the most popular types of wireless networks is cellular networks. In cellular networks we divide the whole network into smaller cells and by this we can have more users in the network with better mobility and Quality of Service (QoS). Cellular networks are divided into different generations.

First generation (1G) cellular networks were introduced around 1980s. The first system was introduced in Japan. The first cellular network in Europe was built in Scandinavia in 1981 and it was known as Nordic Mobile Telephone (NMT). It uses the 450 MHz frequency band. This NMT system was also used in other parts of Europe as well. In America, Advance Mobile Phone System (AMPS) was used. The similarity between these two systems was that they were both analog.

Second generation (2G) for cellular networks started in early 1990s. The first system was introduced in Europe as Global System for Mobile Communication (GSM). It was a digital system and nowadays it is used in more than two hundred countries with around 2.5 billion users. GSM uses a frequency band of 900 MHz and 1800 MHz and also 1900 MHz. GSM has many services like Short Messaging Services (SMS), Caller Identification, roaming etc. Enchantments were made in GSM when General Packet radio Service (GPRS) and Enhanced Data rates for GSM Evolution (EDGE) were introduced. These two systems increased the data rate in GSM. In America, CDMAone was used as a 2G technology.

Figure 1.1: IEEE and ETSI standards for wireless networks [1].

In the third generation (3G) cellular networks, Universal Mobile Telecommunication System (UMTS) was introduced. UMTS has higher data rates as compared to GSM while it enables more services like video conferencing, wireless television and wireless broadband as well. It has been designed to achieve the goal of global coverage. In America, CDMA 2000 was used as a 3G cellular technology.

The fourth generation (4G) of cellular networks is currently under development and hopefully it will be available in 2012. It will be having a data rate of at least 10 Mbps. It will be having more efficient spectral resources and other services as well. WiMAX or Wireless MAN is a 4G technology but some organizations refer it as a 3G technology. WiMAX is in implementation phase and it is the hottest wireless technology nowadays. WiMAX will be providing wireless internet anywhere and anytime.

Outline of Thesis and Contribution

Chapter 2

In this chapter, I discuss WiMAX, technical information and its architecture, QoS and mobility. WiMAX is covered by IEEE 802.16 standard. WiMAX is divided into two types, fixed WiMAX with 802.16d and mobile WiMAX having 802.16e standard. WiMAX is based on flexible and robust air interface. WiMAX physical layer is based on Orthogonal Frequency Division Multiplexing (OFDM) which is of the most effective technique. WiMAX Media Access Control (MAC) layer is also very flexible which can accommodate different traffic types such as voice, video and multimedia

Chapter 3

In this chapter, I discuss Radio Resource Management (RRM) which is very important in cellular networks. In cellular networks the available resources are very limited and I have to utilize them in the best possible manner. There should be an optimized solution to utilize the spectral efficiency. This will increase the overall coverage, capacity and QoS of the network. The main objective of radio resource management is to maximize the number of users in the network and minimize the cost of the network while the QoS should be there as well. In RRM, I control parameters like radio frequency planning, cell planning, link budgeting, modulation schemes, channel access schemes etc.

Chapter 4

In this chapter, I discuss RRM in context of WiMAX network. WiMAX is the technology of the future so RRM in WiMAX will be of great important. WiMAX will be using frequency bands of 2.5 GHz and 3.5 GHz in licensed and 5.8 GHz band in unlicensed regions. Cell planning in WiMAX is very important because coverage and capacity planning depends on it. Link budgeting is also very important because the transmitter power should be on a certain value so that the desired area should be covered and there must be enough power on the receiver side for effective communication. In mobile WiMAX, we require handovers and it will be using hard handovers.

Chapter 5

In this chapter, I discuss our simulation results. My simulation is divided into two parts, link budget and cell planning. In the link budget part, I will focus on link budget in WiMAX. In the cell planning part, I will focus on cell coverage, nominal cell planning and site survey.

CHAPTER 2 WiMAX

The vision of broadband Internet access anywhere and anytime has appeared a distant dream, far from reality for the enormous majority of Personal Computers (PC), laptops and handheld users. WiMAX will be the most up to date wireless technology. WiMAX systems are likely to convey wireless broadband access to residential areas and customers in economical way.

2.1 WiMAX Standards

WiMAX is having two different standards which are described below:

IEEE 802.16-2004

IEEE 802.16-2004 is often called IEEE 802.16d or fixed WiMAX. It uses OFDM and supports fixed and nomadic access in Non-Line of Sight (NLOS) and Line of Sight (LOS) environments. The WiMAX forum uses 3.5 GHz and 5.8 GHz frequency bands for it.

IEEE 802.16e

It is an amendment to 802.16-2004 and it is often called as 802.16e-2005 or mobile WiMAX. This version of WiMAX is designed to support mobility and dynamic mobile radio channels. On the bases of these modifications, it provides mobility and when we have mobility in a network then we need handovers and roaming. WiMAX IEEE 802.16e uses Scalable Orthogonal Frequency Division Multiple Access (SOFDMA) which is a multi-carrier modulation technique and it uses sub channelization. WiMAX forum has not announced the frequency bands. However, the 2.3 GHz and 2.5 GHz bands are supposed to be used for it [3].

WiMAX is a wireless technology which is optimized for the delivery of IP centric services over a large area. Its certification indicates interoperability of the equipment built to the IEEE 802.16 or compatible standard. WiMAX is a scalable wireless platform for making alternative and complementary broadband networks.

2.2 Introduction

WiMAX is a broadband wireless technology which supports different types of services like nomadic access, portable access, fixed and mobility. In the first type, IEEE 802.16-2004 is optimized for fixed and nomadic access. These accesses are Point to Point (PTP) and Point to Multi-Point (PMP) applications. The second type is designed to support portability and mobility. Different types of services provided by WiMAX are described in Table 2.1.

Table 2.1: Different services provided by fixed and mobile WiMAX [3]

|Definition |Devices |Locations, Speed |Handoff or Handover |802.16-2004 |802.16e |
|Fixed Access |Outdoor and indoor |Single, Stationary |No |Yes |Yes |
| |CPEs | | | | |
|Nomadic Access |Indoor CPEs, PCMCIA |Multiple, Stationary |No |Yes |Yes |
| |cards | | | | |
|Portability |Laptops PCMCIA or |Multiple, Walking |Hard |No |Yes |
| |mini Cards | | | | |
|Simple Mobility |Laptops, smart phones|Multiple, Low |Hard |No |Yes |
| | |vehicular | | | |
|Full Mobility |Laptops, smart phones|Multiple, High |Soft |No |Yes |
| | |vehicular | | | |

The WiMAX forum has defined IEEE standard, spectrum bands, duplexing techniques and channel bandwidth for WiMAX. In IEEE 802.16-2004 standard, we use OFDM with 256 carriers while in IEEE 802.16e, we use SOFDMA. In many countries, the licensed spectrum band used for WiMAX is 3.5 GHz while 5.8 GHz is used as an unlicensed band. Time Division Duplex (TDD) and Frequency Division Duplex (FDD) are used as duplexing techniques in WiMAX. In Table 2.2, different frequency bands and duplexing techniques used for fixed and Mobile WiMAX are described.

Table 2.2: Frequency bands and duplexing techniques for fixed and Mobile WiMAX [3]

Fixed WiMAX
|Frequency (GHz) |Duplexing |Channel bandwidth(MHz) |IEEE standard |
|3.4-3.6 |TDD |3.5 |802.16-2004 |
|3.4-3.6 |FDD |3.5 |802.16-2004 |
|3.4-3.6 |TDD |7 |802.16-2004 |
|3.4-3.6 |FDD |7 |802.16-2004 |
|5.725-5.85 |TDD |10 |802.16-2004 |

Mobile WiMAX
| Frequency(GHz) |Duplexing |Channel bandwidth(MHz) |IEEE standard |
| | TDD | 5 |802.16e-2005 |
|2.3-2.4 | | | |
| | TDD | 8.75 |802.16e-2005 |
| | TDD | 10 |802.16e-2005 |
| 2.305-2.320 | TDD | 3.5 |802.16e-2005 |
|2.345-2.360 | | | |
| | TDD | 5 |802.16e-2005 |
| | TDD | 10 |802.16e-2005 |
| 2.496-2.69 | TDD | 5 |802.16e-2005 |
| | TDD | 10 |802.16e-2005 |

The channel bandwidth is highly dependent on the frequency band allocated by regulators. The channel bandwidth is limited to 3.5 MHz and 7 MHz in the licensed band[3]

2.3 Overview of Technical Information

WiMAX is the name of a wireless broadband technology which describes interoperable implementations and different standards of IEEE 802.16. Here, we will discuss some technical information of WiMAX.

2.3.1 WiMAX Physical Layer

WiMAX physical layer uses OFDM as a transmission technique. By using OFDM as a transmission scheme, we have higher data rates as compared to GSM and UMTS.

2.3.2 OFDM Basics

The OFDM technology belongs to the family of multicarrier modulation transmission schemes. The idea is that, we divide the given data stream which has higher bit rates into parallel lower bit rate data streams. After that different subcarriers are used to modulate each individual data stream. These carriers are called subcarriers. By using this technique, we minimize the Inter-Symbol Interference (ISI). The symbol time can be increased if delays are introduced in the channel. With the utilization of this method, delays are introduced in all wireless channels. These channels are only around ten percent of symbol duration time. Consequently, in higher data rate systems, the symbol duration is small. The symbol duration of every stream is increased by dividing the data stream into many parallel streams. Hence, the delay spread is very small when compared to the symbol duration time.

This modulation scheme is a proficient description of multicarrier modulations in which the selected subcarriers lie orthogonal to each other over the duration time of symbols. As so, there will be minimum inter-carrier interference which is caused by the overlapping of subcarriers. There is proper interspacing between these subcarriers as well. Subcarrier bandwidth is

BSC = B / L (2.1)

where B is the nominal bandwidth and it is same as the data rate. While L denotes number of subcarriers and it makes sure that all carriers lie orthogonal to each other over the duration of symbol time.

FDM and OFDM: For better undersanding,we can see the following figures.Here we also discuss about OFDMA and sub-channel or sub-carrier structure and also SOFDMA[39].

[pic]. frequency Figure 2.1: Frequency Division Multiplexing[39].

[pic] . frequency

Figure 2.2: Orthogonal Frequency Division Multiplexing[39].

OFDM and OFDMA

[pic]. frequency . Figure 2.3: Orthogonal Frequency Division Multiple Access(sub-carriers)[39].

Sub-carrier’s with the same color represent a sub-channel.

[pic] Figure 2.4:Uplink subchannelization in WiMAX (OFDM and OFDMA) [39].

In OFDMA several SS’s can transmit at the same time slot over several sub channels.

OFDM and OFDMA symbol structure and scalability[39] [pic] . Figure 2.5:OFDM symbol and subcarrier structure in WiMAX

[pic] . Figure 2.6:OFDMA symbol and subcarriers(subchannels) structure in WiMAX.

Sub-carriers of the same color represent a sub-channel.

SOFDMA

Encoder modulator IFFT Filter DAC RF

a) Transmitter RF chain

Decoder demodulator IFFT Filter ADC RF

b) Receiver RF chain

Figure 2.7: (a) Transmitter and (b)Receiver RF chains in WiMAX

Basic building blocks of Tx RF chain a Rx RF chain shown in the above figure[39].

2.3.3 WiMAX OFDM Parameters

Fixed WiMAX and Mobile WiMAX have very little differences in implementing the OFDM physical layer. Fixed WiMAX or IEEE 802.16-2004 uses OFDM on the physical layer which has a 256 Fast Fourier Transform (FFT) size while Mobile WiMAX or IEEE 802.16e standard uses SOFDMA based physical layer. In Mobile WiMAX, the FFT size is variable it can vary from 128 to 2048 bits. In fixed and mobile WiMAX, different parameters of OFDM and SOFDMA are used on the physical layer. These different parameters are described in Table 2.3 [4].

In IEEE 802.16 standard, it was stated that the physical layer of WiMAX will be operating in the range of 10 to 66 GHz frequency bands. Firstly, IEEE 802.16a was updated in 2004 as 802.16-2004 and it was decided that it will be working on 2 to 11 GHz frequency bands. Then it was again updated as 802.16e-2005 in 2005 and it was also decided that WiMAX 802.16e will be using SOFDMA.The potential benefits of this advanced version are better coverage, self installation, less power consumption, frequency reuse and spectral efficiency.

Table 2.3: Different parameters in WiMAX [3]

|Parameter |Fixed WiMAX OFDM |Mobile WiMAX Scalable OFDMA |
|FFT size |256 |128 512 1024 2048 |
|Number of used data subcarriers |192 |72 360 720 1440 |
|Number of pilot subcarriers |8 |12 60 120 240 |
|Number of null/guard band subcarriers |56 |44 92 184 368 |
|Cyclic prefix or guard time (Tg/Tb) |1/32 |1/16 1/8 1/4 |
|Oversampling rate (Fs/BW) |Depends on bandwidth: 7/6 for 256 OFDM, 8/7 for multiples of 1.75MHz, and 28/25 |
| |for multiples of |
| |1.25MHz, 1.5MHz, 2MHz, or 2.75MHz. |
|Channel bandwidth (MHz) |3.5 |1.25 5 10 20 |
|Subcarrier frequency spacing (kHz) |15.625 |10.94 |
|Useful symbol time (ms) |64 |91.4 |
|Guard time assuming 12.5% (ms) |8 |11.4 |
|OFDM symbol duration (ms) |72 |102.9 |
|Number of OFDM symbols in 5 ms frame |69 |48.0 |

2.3.4 WiMAX MAC Layer

WiMAX MAC layer is working as an interface between the WiMAX physical layer and upper transport layers. The MAC Service Data Units (MSDUs) are the packets which MAC layer takes from the upper layers. Then for transmission these packets are converted into MAC Protocol Data Units (MPDUs). In MAC layer design a convergence sublayer is included which can be used as an interface to higher layer protocols like Asynchronous Transfer Mode (ATM), Time Division Multiplexing (TDM), Voice, Ethernet and IP. At this time, WiMAX only supports IP and Ethernet but it provides mapping information to the higher layers. The convergence sublayer of WiMAX physical layer supports the MSDU header control to decrease the overhead load on each packet which is caused by the upper layers [4].

WiMAX MAC layer uses a variable length MPDU and it also provides flexibility for their efficient transmission. For instance, if we want to save physical layer overhead, we can add multiple MPDUs of same or different lengths to a single burst. Similarly, we can save MAC header overhead by adding multiple MSDUs which belong to the same higher layer protocol into a single MPDU. On the other hand, large MSDUs can be fragmented into smaller MPDUs and after that it can be sent across multiple frames.

In Figure 2.8, different examples of MAC Packet Data Unit (PDU) frames are shown. Every MAC frame contains a Connection Identifier (CID) and every MAC frame starts with a Generic MAC Header (GMH). The length of frame depends on Cyclic Redundancy Check (CRC), sub-headers and payload. This payload can be a transport message or a management message. This transport payload may include bandwidth requests or retransmission requests. The type of transport payload is recognized by the sub-header that immediately follows it. MAC layer also supports Automatic Repeat Request (ARQ).Using ARQ, unfragmented and fragmented MSDUs can be retransmitted in case of loss. The maximum length of the frame is 2,047 bytes [3].

|GMH |Other SH |Packed Fixed size |Packed Fixed size |… |Packed Fixed size |CRC |
| | |MSDU |MSDU | |MSDU | |

a) MAC PDU frame carrying several fixed length MSDUs packed together

|GMH |Other SH |FSH |MSDU Fragment |CRC |

b) MAC PDU frame carrying a single fragmented MSDU

|GMH |Other SH |PSH |Variable size MSDU|PSH |Variable size MSDU|CRC |
| | | |or Fragment | |or Fragment | |

c) MAC PDU frame carrying several variable length MSDUs packed together

|GMH |Other SH |ARQ Feedback |CRC |

d) MAC PDU frame carrying ARQ payload

|GMH |Other SH |PSH |ARQ Feedback |PSH |Variable size MSDU or Fragment |CRC |

e) MAC PDU frame carrying ARQ and MSDU payload

|GMH |ARQ Feedback |CRC |

f) MAC management frame

g) Figure 2.8: Examples of various MAC PDU frames [4].

2.3.5 Channel Access Mechanisms

The WiMAX MAC layer is completely responsible for assigning bandwidth for all uplink and downlink users at the Base Station (BS). This is the only time when the BS has all the control over bandwidth allocations. During this period, multiple users are trying to connect or already connected with the BS. In this case, BS assigns bandwidth to all the users. Then it is distributed on different connections. The BS is also responsible for controlling all the downlinks and uplinks by the users. The BS may allocate bandwidth to each Mobile Station (MS) for downlinks. It is based on the requirement of the incoming traffic. The MS can also request bandwidth allocations for uplinks.

The WiMAX standard supports several mechanisms by which an MS may request and get uplink bandwidth, depending on specific QoS and traffic parameters related to the required service. BS assigns shared resources from time to time to each MS, which can be used for different services. This process is called as polling. Polling may be done either one by one which is called unicast or in groups which is called multicast. When we have insufficient bandwidth to poll every MS one by one then multicast polling is used. In multicast polling, every polled MS tries to use a dedicated or shared slot. WiMAX gives a resolution mechanism for the scenario where more than one MS are trying to utilize the dedicated or shared slots. The MS can request for more bandwidth in many ways. For instance, by sending MPDU bandwidth request alone, the ranging channel can be used as well for sending a bandwidth request and piggybacking the bandwidth request on generic MAC packets [4].

2.3.6 QoS in WiMAX

The QoS is determining the fact that how successfully a wireless technology can transfer high value services like voice and video. For good QoS, the latency, jitter and packet loss should be minimized. After solving these issues, a good QoS is guaranteed. WiMAX has a very low latency across the wireless period. Most vendors have products in which we have latency less than 10 ms from the transmitter to receiver. The latency is measured from end to end. For instance, Voice over IP (VoIP) is highly vulnerable to latency. If the latency increases to 150 ms, the quality of the call begins to decrease. If the latency is equal to or above 200 ms, a call or conversation would be having very low quality [5].

Figure 2.9: Latency in the air of a WiMAX network [5].

In WiMAX, the large bulk of latency does not occur on the air link between subscribers and base station. This latency can be introduced on the wired portion of the connection between the subscriber and whatever the "other end" could be,i.e it can be a web server, IPTV server or VoIP calls. Figure 2.2 illustrates the latency on the wireless portion in a WiMAX network.

WiMAX also describes an idea of a service flow. The unidirectional flow of packets with a specific set of QoS parameters is called service flow and it is expressed by a service flow identifier (SFID). Different SFIDs and applications are shown in Table 2.4.

Table 2.4: Service class and applications [5]

|Service Class |Applications |QoS Specification |
|Unsolicited Grant Services |VoIP |Maximum sustained rate, Maximum latency tolerance, Jitter |
|(UGS) | |tolerance |
|Best-effort service (BE) |Web browsing, data transfer|Maximum sustained rate, Traffic priority |
|Real-time Polling service |Streaming audio and video | |
|(rtPS) | |Minimum reserved rate, Maximum sustained rate, Maximum latency |
| | |tolerance, Traffic priority |
|Non-real-time Polling service|FTP |Minimum reserved rate, Maximum sustained rate, Traffic priority |
|(nrtPS) | | |
|Extended real-time Polling |VoIP (voice with activity | |
|service |detection) |Minimum reserved rate, Maximum sustained rate, Maximum latency |
|(ErtPS) | |tolerance, Jitter Tolerance, Traffic priority |

2.3.7 WiMAX Mobility Support

In fixed broadband access, WiMAX distinguishes four mobility related usage circumstances:

Nomadic: In this scenario, a fixed location is allocated to the user to utilize the services. In order to connect from a different location, a break or disconnection is supposed to be faced by the user in this case.

Portable: Employing nomadic access with a portable device, the portability is ensured for the user at the cost of handovers.

Simple mobility: Almost uninterrupted handovers are achieved besides attaining a speed of 60 km/h by the user with very short time intervals (ranging up to few milliseconds).

Full mobility: The user can move up to 120 km/h speed. Mobility and seamless handovers with less than 50 ms latency and < 1 % packet loss is supported.

WiMAX network supports both fixed and nomadic applications. However, an extension in support for portability and full mobility can be achieved in addition, thereafter. IEEE 802.16e-2005 standard describes a structure for supporting mobility management. The Standard describes signaling mechanisms for tracking subscriber stations which are moving from one BS coverage range to another in active mode. The IEEE standard has protocols to allow a seamless handover of enduring connections from one BS to another. WiMAX Forum has used the structure defined in IEEE 802.16e-2005 to additionally make network architecture structure such that it supports mobility management. This architecture facilitates the IP layer mobility using mobile IP.

2.3.8 Multicast and Broadcast Services

This MAC layer handles the Multicast and Broadcast Services (MBS). MBS have function and features in the standard which are described as

• The MS has a signaling system that requests and after confirmation launch the multicast and broadcast services.

• The subscriber station access the multicast and broadcast services over a single/multiple BS depending upon its capability and desire.

• Multicast and broadcast services are associated with QoS and encrypted by a globally describe traffic encryption key.

• There are different methods to deliver multicast and broadcast services traffic to idle mode subscriber stations.

• MAC layer supports the macro diversity to enhance the delivery performance of multicast and broadcast services traffic.

2.4 WiMAX Features for Performance Enhancement

WiMAX describes the advanced features of improving the performance. These advanced features which can be supported are Advanced Antenna Systems (AAS), hybrid ARQ and frequency reuse. However, the former two will be elaborated in detail under this section and the later (frequency reuse) will be discussed in the next chapter.

2.4.1 Advanced Antenna Systems

IEEE 802.16 standard provides the support for implementing advanced multi-antenna solutions which improve the system performance. We are deploying AAS to get gain in the capacity of the system and more bandwidth efficiency. The varieties of multiple antennas mentioned in AAS are as follows:

Transmit diversity: For transmit diversity, there may be two or more antennas on the transmitter and receiver sides. A numbers of space time block coding schemes can be employed to achieve transmit diversity for the downlink.

Beamforming: Beamforming ensures better capacity, more coverage and greater reliability in the network.The antenna beam can be creat in the direction of desired user and block the interferers.

Spatial Multiplexing: Different streams are transmitted on multiple antennas in spatial multiplexing.

2.4.2 Hybrid ARQ

Hybrid ARQ is the combination of Forward Error Correction (FEC) and ARQ. It is implemented at the physical layer with FEC. It improves the link performance when compared with traditional ARQ at the cost of complexity. The FEC coder encoded the block of data along with the CRC code before transmission. If the decoder fails to decode the received block, the retransmission is requested. The received block is combined with the last detected code and serves as the input to the FEC decoder, thereafter. There are three types of Hybrid ARQ, the Type I is called Chase combining,Type II is called Incremental redundancy and Type III is self decodable packet[6].

2.5 WiMAX Network Architecture

The information about the air interface is specified in the mobile WiMAX standard but it seems lying unspecified about the end-to-end WiMAX network requirements. A network reference model has been designed by WiMAX Network Working Group (NWG). The deployment of WiMAX can be accomplished by employing this architecture. With the help of this framework, we can ensure interoperability among different WiMAX components and operators. A logical division for a WiMAX network into three different parts can be interpreted as Mobile Stations (MS), Access Service Network (ASN) and Connectivity Service Network (CSN). Figure 2.3 shows important functional entities of a WiMAX network [4].

[pic] Figure 2.10: WiMAX network architecture [4].

CHAPTER 3 RADIO RESOURCE MANAGEMENT WITH FORMAL TECHNOLOGY
Introduction

Radio Resource Management (RRM) is a control mechanism for the overall system which is used to manage radio resources in the air interface within a cellular network. The main objective of my study of RRM is to analyze and determine a way to utilize the available spectral resources as efficiently as possible. The frequency license fees, real estate cost, distribution network and maintenance are the issues which dominates the cost of deploying a cellular network. Hence, the limitation of spectral resources is being faced due to the above mentioned factors regarding their cost effectiveness. The core objective of this thesis is to serve the purpose of maximization of the performance along with spectral efficiency enabling maximum number of users in our network and to bring QoS up to the mark.

Radio Resource Management (RRM) is of vital importance in cellular systems due to the bandwidth limitations. In RRM, point to point capacity issues are not considerable whereas it suitably tackles multi-cell traffic problems. For cellular systems, the whole network is geographically divided into smaller geometric regions called cells. In each cell, there is a network infrastructure element called BS. These BS are connected to each other and to the core network via radio interface. The overall number of users (traffic) and performance of the whole network depends upon the individual cells performance. The optimum utilization of this radio interface is of key important. An efficient RRM algorithm is a basic requirement for it, as efficient RRM techniques enhance the overall capacity of the system and decrease the cost effectively [7]. RRM involves techniques and algorithms for controlling parameters which are as follows:

• Frequency Band Allocation

• Cell Planning

• Link Budget

• Call Admission Control

• Modulation Schemes

• Multiple Access Schemes

3.1 Frequency Band Allocation

Frequency band allocation is one of the most important parameters of RRM. The world is lacking global standards for cellular communications. In different regions of the world even a single frequency band is used for different cellular systems. Almost every country has its own regulatory authority. For instance, Federal Communications Commission (FCC) is the authority which is responsible for the allocation of frequency bands in the US. International Telecommunication Union (ITU) is a United Nation based organization which is working to standardize the frequency bands all over the world [9]. It is very important that we have the same frequency band all over the world for one technology as it would be easier and convenient for a user to use the same equipment and technology anywhere.

Due to historical and political reasons, there are different frequency bands allocated for cellular communication systems in the world. The world is divided into three regions and all the three regions have different frequency bands which are illustrated in Figure 3.1 below [8].

[pic]

Figure 3.1: Different regions of frequency allocation in the world [8].

Region 1 consists of Europe, Africa, Russia and some parts of the Middle East. Regions 2 covers USA, Canada and all the Latin America while in Region 3 China, Australia, India, Pakistan, Japan and other countries of Asia and Oceania are located. Almost every cellular technology has different frequency bands in these three regions. But even in one region there are different frequency bands for same technologies.

3.2 UMTS/HSDPA/HSUPA frequency bands deployment

• “Band I (W-CDMA 2100) is used in Europe, Africa (ITU Region 1), Asia, Oceania and Brazil (part of ITU Region 2).

• Band II (W-CDMA 1900) is used in North America and South America (ITU Region 2).

• Band IV (W-CDMA 1700 or Advanced Wireless Services) is used in the United States by T-Mobile.

• Band VIII (W-CDMA 900) is used in Europe, Asia and Oceania (ITU Region 1 and ITU Region 3).

• Band V (W-CDMA 850) is used in Australia, Brazil, Canada, USA ,other parts of South America and some parts of Asia (ITU Region 2 and ITU Region 3).

• Band XII - XIV were added for future use in the 700MHz spectrum auctioned in the United States and Canada in early 2008.” [10]

Acquisition of a frequency license is an issue to be addressed at the forth most priority while deploying a cellular network. Higher costs have to be paid by the companies to the local regulatory authorities for this purpose. The overall bandwidth of the system depends on that frequency band. The cellular companies do not have a choice for the acquisition of frequency band as the authorities have predefined frequency bands for different cellular technologies. Hence, to make an efficient use of the provided band of frequency, the role of employing RRM emerges as of key importance.

3.3 Cell Planning

The development of cellular networks has brought a revolution. In this modern era, mobile telephones, personal communications, wireless broadband internet and other applications widely use cellular networks. In cellular networks, the whole geographical area is divided into smaller geometric parts which are termed as cells. A Base Transceiver Station (BTS) or BS is installed in each cell of a cellular network with a low power transmitter. Each cell has its own transmitter, receiver and control unit. These base stations are connected to each other and to the Mobile Switching Centre (MSC) via radio interface. The MSC is connected to the Public Switched Telecommunication Networks (PSTN). The basic overview of cellular system is shown in Figure 3.2 [11].

The whole procedure of dividing the network into cells and placement of base stations in these cells is called cell planning. Cell Planning is usually applied before deploying the network, increase in the capacity of the system can also be achieved thereafter applying cell planning. The network is required to be divided into the cells in a way to achieve an efficient and optimum condition as the base stations are also to be installed accordingly. Cell planning also includes call traffic capacity. As the number of users in a cell increases, smaller cells can be created and there is an increase in the overall capacity of the network as a result. The number of cells is required to be optimum and QoS up to the standard. The installation cost for a BS is very high as it also includes the cost or rent of the real estate.

[pic]

Figure 3.2: General architecture of cellular system [9].

The cells used in the planning of cellular communication are hexagonal in shape. The hexagons are equidistant from the centers, making them preferable to be adopted in cellular networks. The hexagons are shown in Figure 3.3 [12]. In practice an ideal hexagonal does not exist. The distance between a cell and adjacent cell is

d = [pic]R (3.1)

where R is the radius of cell.

Area of one cell = A = 1.5[pic]R. (3.2)

Total Area of network = Number of cells x Area of one Cell. [11] (3.3)

3.3.1 Cell Site

Cell site is a very common term which describes the location or site where the base station is deployed. Cell site or BS is consisted of a tower, mounted transmitter and receiver antennas, power supply, the backup power supply and controlling element which is commonly termed as cell Base Station Controller (BSC).

The BTS are connected to each other via optical fiber or microwave links. BTS consists of two parts, BSC and Radio Network Controller (RNC). These BSCs are connected to Mobile Telephone Switching Centre (MTSC) or MSC.

[pic]

Figure 3.3: Hexagonal cells [12].

The most important parameter which is concerned with the cell site is the range of cell site. The range of the cell site depends upon the transmitter power, size of antenna, antenna height, the direction of antenna and geographical position of the cell site.

3.3.2 Frequency Reuse

Frequency reuse means that same frequencies can be used in a different area for different communications. The capacity of the system can be increased by using frequency reuse. A problematic situation in this regard is to determine the frequency reuse interval that is to specify the number of cells after which we can reutilize the same frequency again as the same frequency reuse introduces interference. Every cell is being allocated a number of fixed frequency channels. If we have a total number of cells N and number of available frequency channels assigned to a cell is K then the frequency reuse factor is K / N. Frequency reuse procedure is shown in Figure 3.5 [15].

[pic]

Figure 3.4: Cell site [14]. Figure 3.5: Frequency reuse of 1/7 [1].

3.3.3 Types of Cells

As the number of users increases in a single cell, the capacity of the system is overloaded and the QoS is affected. This problem is solved by dividing the cell into smaller cells. Below are some types of cells regarding the size of cell, power and height of antenna.

• Macro Cells

• Micro Cells

• Nano Cells

• Pico Cells

• Umbrella Cells

• Sectorized or Selective Cells [1]

1) Macro Cells

A common type of cells which is implemented in cellular communication is macro cells. These are the largest cells and cover an area of more than ten kilometers. These cells are usually used in rural and mountainous regions as we do not have a lot of traffic in these regions. In this cell, the BS is usually placed on the top of a building or on the hill.

2) Micro Cells

Micro cells are commonly used in urban areas. The coverage area for micro cells is up to a few kilometers. In these cells, the BS is required to be placed at the roof of the building, about 10 to 20 meters above.

3) Nano Cells

In cities with densely populated areas, micro cells are replaced by smaller cells which are called nano cells. The geographical area covered by these cells is less than a kilometer nearly a few hundred meters. The BS in this case needs to be placed at the top of a roof but not very much higher.

4) Pico Cells

Pico cells are the smallest cells used in cellular networks. It has a coverage area of few meters, nearly 30 to 80 meters.

[pic]

Figure 3.6: Umbrella cell.[1]

5) Umbrella Cells

An umbrella cell consists of a macro cell and several micro cells as shown in Figure 3.6 [14]. Umbrella cells are used when a mobile station is moving at a fast speed. In case of micro cells, a lot of handovers will be required. To avoid this situation, this user is connected to a macro cell, covering the whole area and in this case, the mobile user remains in the same cell for a longer time period. By using this method, number of handovers can be limited. An umbrella cell is a very good practical example of RRM.

6) Sectorized or Selective Cells

Usually, a cell has coverage in all directions because we use three antennas on a single BS with 120 degree apart from each other. Thus, the coverage is almost 360 degree, means almost equal in all directions. In some cases, we don’t require coverage in all directions. For instance, in case of a tunnel, the coverage is only required in one direction. These types of cells are known as sectorized or selective cells.

4. Link Budget

Link budget is the estimation and determination of a transmitted signal upon reaching the receiving end. Link budget encapsulates a significant importance while doing research work or designing in the field of communication engineering.

Determining and adding all the gains and losses in a communication system is called the link budget. Link budget specifies the amount of transmitter power needed to transmit a signal with a certain Signal to Noise Ratio (SNR) and acceptable Bit Error Rate (BER). Path loss, noise, rain loss, connectors or cable losses, receiver sensitivity and antenna gains are the factors which are required to be taken into the account while estimating the link budget. Figure 3.7 illustrates the link budgeting procedure [16].

1. Calculation of Link Budget

Link budget is very important part of the network planning process. Link budget is a process for indoor and outdoor applications. Link budget gives the measurements which are required for the coverage, capacity and QoS requirement of the network. In cellular networks, there are two types of link budget calculations such as:

• Link from the BS to the Subscriber Station (SS)

• Link from the SS to the BS

The Link budget adds all the gains and losses to the transmitter power (in dB) to the received power. In the link budget we can calculate the following parameters:

• Path loss

• Antenna gain

• Link margin

• Diffraction loss

• Coaxial cable and connector losses

• Attenuation (rain or fog)

• SNR

[pic] . Figure 3.7: Link budget [16].

4. Call Admission Control

Call admission control involves both new and handover calls. Handover or Handoff is a procedure in which an ongoing call or data session is transferred from one cell to another cell due to the movement of mobile user. But in this transfer the QoS, good voice quality and fast data transfer is required to be maintained. An efficient RRM algorithm includes call admission control as well.

3.5.1 Handovers

Handover as discussed earlier is a criterion for retention of an ongoing call from one cell to another cell when the user is moving in the range of different cells. If the handover criterion is not specified, the probability for a call to be dropped increases extensively. Some important algorithms used for handovers are discussed below:

Non Prioritized Handover Scheme (NPS)

This scheme assigns same priority to all the calls in a particular cell that is the equal priority for new calls and handovers. When a new call is initiated in a cell or a handover is transferred to that cell, a free channel is automatically assigned to it. In this scheme, all the channels are available for new or handover calls. A limitation with this scheme arises in a case when all the channels are occupied and no more new calls can be made in that cell. Hence, the user is required to move into another cell to make a call. Similarly, if all the channels are busy in a cell and a handover is transferred to that cell, the call will be dropped due to unavailability of free channels.

Reserved Channel Scheme (RCS)

In RCS, some frequency channels are particularly reserved for handover calls. If there are total number of channels available ‘N’ and some number of the ‘N’ channels ‘S’ are reserved for handovers. The reserved ‘S’ channels are only used for handover. In this scenario, when handover occurs, it is automatically assigned a reserved channel even all the other channels are occupied. These reserved channels are never assigned to new calls. The number of reserved channels can vary in different cellular networks.

3.5.2 Types of Handover

There are two types of handovers which are currently being used in cellular networks which are as follows:

Hard Handovers

In hard handovers, the channel in the source cell (from where the call originates) is released first and after that the channel in the target cell (where the call is transferred) is engaged. Disconnection from the source cell takes place first and the target cell is connected thereafter. These types of handovers are also known as Break Before Make (BBM). In this type, the data is temporarily stored in a register during the handover. This data is once utilized after the handover and it is never used again. This type is advantageous in the sense that at anytime only one channel is used for one call. A problematic situation can occur in this type of handovers for instance, if all the channels in the target cell are busy then the call is not transferred to that cell as there are no free channels available in that cell. Hence, the call is dropped due to early disconnection from the source cell.

Soft Handovers

In this case, the channel in the source cell is retained for a while along with the channel in the target cell. The connection to the target cell is first established before the termination of the connection from the source cell. In this way, the user is connected with two cells simultaneously. These types of handovers are also known as Make Before Break (MBB). The significance of this scheme relies in the fact that the channel in the source cell is only released when a reliable connection in the target cell is established. Hence, the call drop rate decreases in this scenario. On the other hand, it is wastage of resources to use two channels simultaneously for one call. The hardware required for soft handovers is costly and complex as it must be compatible to engage both channels simultaneously.

Intra-cell handovers

In this type of handovers, source and the target cell are the same. The change of channel occurs only in case of interference in the channel. These types of handovers are called as intra-cell handovers.

5. Modulation Schemes

In wireless networks, different modulation schemes are used for different types of communications. In RRM perspective, the selection of an efficient modulation scheme is of significant importance. In modulation, a baseband signal (low frequency signal) is multiplied with a carrier signal or modulator signal (normally a high frequency signal). The signal can be transmitted for longer ranges by using modulation. A carrier signal is normally a sinusoidal signal of high frequency. At the receiver end, the signal is then demodulated with the help of a device called demodulator. There are two types of modulations, analog modulations and digital modulations.

3.6.1 Analog Modulations

In analog modulation, the modulation is applied continuously in response to the analog information signal.A low-frequency message signal (top) may be carried by an AM or FM radio wave.Common analog modulation techniques are:[37]

• Amplitude modulation (AM) (here the amplitude of the carrier signal is varied in accordance to the instantaneous amplitude of the modulating signal)

• Double-sideband modulation (DSB)

• Double-sideband modulation with unsuppressed carrier (DSB-WC) (used on the AM radio broadcasting band)

• Double-sideband suppressed-carrier transmission (DSB-SC)

• Double-sideband reduced carrier transmission (DSB-RC)

• Single-sideband modulation (SSB, or SSB-AM),

• SSB with carrier (SSB-WC)

• SSB suppressed carrier modulation (SSB-SC)

• Vestigial sideband modulation (VSB, or VSB-AM)

• Quadrature amplitude modulation (QAM)

• Angle modulation

• Frequency modulation (FM) (here the frequency of the carrier signal is varied in accordance to the instantaneous frequency of the modulating signal)

• Phase modulation (PM) (here the phase shift of the carrier signal is varied in accordance to the instantaneous phase shift of the modulating signal)

3.6.2 Digital Modulations

In digital modulations, a digital signal is multiplied with a carrier signal. Some important types of digital modulation are as follows [37]:

• Frequency Shift Keying (FSK)

• Amplitude Shift Keying(ASK)

• Phase Shift Keying (PSK)

• Quadrature Amplitude Modulation(QAM) - a combination of PSK and ASK

• Multi-frequency Shift keying (MFSK)

• Binary Phase Shift keying (BPSK)

• Quadrature Phase Shift keying (QPSK)

• Differential Phase Shift Keying (DPSK)

• Quadrature Differential Phase Shift Keying (QDPSK)

• Gaussian Minimum-shift keying (GMSK)

• Orthogonal Frequency Division Multiplexing (OFDM)

3.6.3 Spread-spectrum techniques:

• Direct-sequence spread spectrum (DSSS)

• Frequency-hopping spread spectrum (FHSS)

3.6.4 Analog-over-analog methods:

• Pulse-amplitude modulation (PAM)

• Pulse-width modulation (PWM)

• Pulse-position modulation (PPM)

3.6.5 Analog-over-digital methods:

• Pulse-code modulation (PCM)

• Differential PCM (DPCM)

• Adaptive DPCM (ADPCM)

• Delta modulation (DM or Δ-modulation)

3.7 Multiple Access Techniques

In cellular communication, numbers of channels in a cell are limited. Hence, the capacity of the whole network is limited. Thus, multiple access techniques are of great importance. Multiple access implies the utilization of service by several users at the same time. A frequency channel can be shared among many users at the same time and the capacity of the network can be increased. These multiple access techniques are used on the physical layer. Some important multiple access techniques are described below:

1. Frequency Division Multiple Access (FDMA)

In this channel access scheme, the whole frequency band is divided into smaller frequency bands and each user is assigned a separate frequency band. These frequency bands are allocated to the users by ensuring minimum interference between different frequency bands.

2. Time Division Multiple Access (TDMA)

TDMA is also used for wireless networks where we have shared resources. In TDMA,same frequency band is available for all users which can be used in different time intervals. Each user is assigned a time slot and during that period, it can utilize the whole frequency band. TDMA is used in 2G cellular networks while a combination of TDMA and FDMA is used in GSM.

[pic]

Figure 3.8: Comparison of FDMA, TDMA and CDMA [19].

3. Code Division Multiple Access (CDMA)

CDMA scheme adopts the method for transmission of data of multiple users simultaneously with a code. In FDMA, the bandwidth is divided among the users while in TDMA, the time is divided among the users whereas in CDMA, both time and frequency are divided. The difference between FDMA, TDMA and CDMA is illustrated in Figure 3.9 [6].

4. Orthogonal Frequency Division Multiple Access (OFDMA)

OFDMA is a new scheme and it is based on OFDM. In this scheme, the carrier signal is divided into smaller subsets and a subset of carrier signals is used to transmit the data of a single user. OFDMA can be used alongside with OFDM to increase the QoS of the system.

CHAPTER 4

RADIO RESOURCE MANAGEMENT IN WiMAX

Introduction

WiMAX is an extension of Wireless LAN 802.11 (Wi-Fi) and it will be providing wireless broadband services. WiMAX is a possible replacement of Digital Subscriber Line (DSL). WiMAX is divided into two standards, fixed WiMAX and mobile WiMAX. In fixed WiMAX, the user is having a fixed location while in mobile WiMAX, users are provided with mobility to move around. Fixed WiMAX is currently in deployment phase in many parts of the world while mobile WiMAX is in planning phase and it will be implemented in few years.

In the previous chapter, RRM was discussed in perspective of general cellular networks. Here, the focus will be on RRM in WiMAX networks. The architecture of WiMAX network is similar to the general cellular networks architecture. Hence, RRM is of great importance in WiMAX as well. The main function of RRM is to ensure the QoS. The optimal solution in designing and planning a network is critical due to the limitation of resources. Different parameters of RRM in WiMAX will be discussed here which are as follows:

• Frequency Band Allocation of WiMAX

• Cell Planning in WiMAX

• Link Budget of WiMAX

• Call Admission Control in WiMAX

• Modulation Schemes in WiMAX

4.1 Frequency Band Allocation in WiMAX

In the previous chapter, it was discussed that the frequency bands used for cellular networks are not similar in different parts of the world. Similarly, different frequency bands are used for WiMAX in different regions of the world as shown in Figure 4.1 [20]. There are two types of frequency bands used for WiMAX, unlicensed bands and licensed bands [20].

[pic]

Figure 4.1: Frequency bands used for WiMAX [20].

Unlicensed frequency bands are used within a specific area. Normally, they are used for special purposes for instance, in educational campuses. Licensed frequency bands are used by the operators after paying the fees. In Table 4.1, different frequency bands used for WiMAX are described [20].

Table 4.1: Frequency bands for WiMAX [20]

|Geographical Area |Frequency Bands |Frequency Bands |
| |(Licensed) |(Unlicensed) |
|North America |2.3 and 2.5 GHZ |5.8 GHz |
|Central and South America |2.5 and 3.5 GHZ |5.8 GHz |
|Europe |3.5 GHZ |5.8 GHz |
|Asia |3.5 GHZ |5.8 GHz |
|Middle East and Africa |3.5 GHZ |5.8 GHz |

However, in some parts of Asia and the Middle East, 2.3 and 3.3 GHz frequency bands are also used.

4.2 Cell Planning in WiMAX

Cell planning involves two parameters, call traffic capacity model and cell coverage. The cell coverage model is used to estimate the coverage of cell. The cellular network is geographically divided into different regions such as urban area, suburban area, rural area highways and mountainous regions.

Cell planning in WiMAX is similar to any other cellular network in terms of coverage and capacity planning. The cell size in WiMAX network is larger as compared to a GSM or UMTS cell. In WiMAX network, different cells are used for urban, suburban, indoor areas and outdoor areas. Different cells used in WiMAX networks are as follows:

Macro Cells: used for highways, naval areas and mountainous regions.

Micro Cells: used in suburban areas.

Pico Cells: used in urban areas.

Femto Cells: used in highly dense urban areas.

Sectorized Cells: Sectorized cells are used in tunnels or where directional coverage is needed. Four Sectors Pre WiMAX is shown below:

4.2.1 Technical Cell Site Issues for WiMAX

1. The distance between the nominal sites is 500m for dense urban and urban areas. 1000 to 2000 km for the rest clutter types [20].

2. The height of antennas above the ground level must be 30 to 45m. For the roadside, the antenna tower is placed on a height of 45m[1].

3. The antennas can be placed close to roof edge. This will give more free space for changing antenna tilts and antennas can be tilted according to the user capacity.

4. There must be no obstacles within 500m in the area of transmission[1] .

5. There are three sectors in which antenna are placed, at 0o, 120o, 240o as a reference. The antenna placement can be changed according to the situation.

6. There must be LOS in neighboring cell sites if there is a microwave link between these sites.

4.2.2 WiMAX Network Planning

In WiMAX network planning process some critical parameters are needed. WiMAX network can be divided into three categories which are described as follows [1]:

• Landscape: The landscape includes geographical location, market information and the size of area to be covered by the networks.

• Subscribers: The subscriber profile, subscriber usage model, mobility model, data demand model and grade of Service are included in the category of subscribers.

• Technology and Operational: Technology capabilities, component capabilities, costs to purchase the equipment, cost to obtain the facilities and building rental are considered in this category.

4.3 Link Budget in WiMAX

WiMAX system parameters, OFDMA parameters and propagation model are the terms discussed in the link budget estimation of a WiMAX network. All these parameters are described in the Table 4.2, 4.3 and 4.4 [38].

Table 4.2: System parameters for mobile WiMAX [38]

|System Parameters |System Parameter Values |
|Number of 3-Sector Cells |19 |
|Operating Frequency |2.5 GHz |
|Duplex |TDD |
|Channel Bandwidth |10 MHz |
|BS-to-BS Distance |2.8 km |
|Min. Mobile-to-BS Distance |36 m |
|Antenna Pattern |70° (-3 dB) with 20 dB front-to back ratio |
|BS Height |32 m |
|Mobile Terminal Height |1.5 m |
|BS Antenna Gain |15 dBi |
|SS Antenna Gain |-1 dBi |
|BS Maximum PA Power |43 dBm |
|Mobile Terminal Maximum PA Power |23 dBm |
|No. of BS TX/RX Antenna |1/2/4 |
|No. of MT TX/RX Antenna |2 |
|BS Noise Figure |4 dB |
|SS Noise Figure |7 dB |

There are two sets of OFDMA parameters for channel bandwidth, 10 MHz and 5 MHz. Table 4.3 describes there parameters [38].

Table 4.3: OFDMA parameters for mobile WiMAX [38]

|Parameters |Values Set 1 |Value Set 2 |
|System Channel Bandwidth (MHz) |10 |5 |
|Sampling Frequency (Fp in MHz) |11.2 |5.6 |
|FFT Size (NFFT) |1024 |512 |
|Sub-Carrier Frequency Spacing |10.9375 KHz |10.9375 KHz |
|Useful Symbol Time (Tb = 1/f) |91.4 us |91.4 us |
|Guard Time (Tg =Tb/8) |11.4 us |11.4 us |
|OFDMA Symbol Duration (Ts =Tb + Tg) |102.9 us |102.9 us |
|Frame duration |5 ms |5 ms |
|Number of OFDMA Symbols |48 |48 |
|DL PUSC |Null Subcarriers |184 |92 |
| |Pilot Subcarriers |120 |60 |
| |Data Subcarriers |720 |360 |
| |Sub-channels |30 |360 |
|UL PUSC |Null Subcarriers |184 |92 |
| |Pilot Subcarriers |280 |140 |
| |Data Subcarriers |560 |280 |
| |Sub-channels |35 |17 |

The propagation model and the general link budget for Mobile WiMAX are given in Table 4.4 and Table 4.5 [38].

Table 4.4: Propagation model for mobile WiMAX [38]

|Parameters |Value |
|Log-Normal Shadowing SD (σs) |8 dB |
|BS shadowing correlation |0.5 |
|Penetration Loss |10 dB |

Table 4.5: Link budget for Mobile WiMAX [38]

|Base Station Infrastructure |Range |
|Rx Antenna Gain |15 dBi |
|Rx Antenna Diversity Gain |2 dBi |
|Rx Noise Figure |4 dB |
|Margins |
|Log Normal Fade Margin |5.56 dB |
|Fast Fading Margin |4 dB |
|Interference Margin |3 dB |
|Penetration Loss |10 dB |
|Base Station Rx Sensitivity |
|Thermal Noise |-174 dBm/Hz |
|Sub-Carrier Spacing |10.94 KHz |
|SNR Required |-6 dB |
|Delta from limiting cell range distance |0.17 |
|Rx Sensitivity (per sub-carrier) |-135.6 dBm |
|Rx Sensitivity (composite) |-114 dBm |
|System Gain |153.1 dB |
|Max. Allowable Path Loss |130.5 dB |

4.3.1 Signal availability test:

[pic]

Figure 4.2:Link budget calculator[36]

[pic] Table 4.6: Signal availability test output.[36]

4.4 Call Admission Control in WiMAX

WiMAX will be providing voice calls and broadband services. WiMAX has a share nature of medium. Thus, the efficient utilization of available spectral resources is mandatory. There are two types of users is a WiMAX network, permanent user and temporary users. Permanent users are permanently connected to the network and using the services all the time. Temporary user is only connected to the network when it wants to use the services. The permanent user can be a company using the broadband services. Hence, a permanent link is needed for this type of connection and a permanent channel is assigned to that connection. For the other user, there is no need of a permanent link, the channel is only assigned when required. WiMAX has two types of calls (data sessions or connections), new calls and handovers. Handovers have higher priority as compared to new calls.

4.4.1 Handovers in WiMAX

As we discussed in earlier chapters that WiMAX has two standards 802.16d and 802.16e. In WiMAX 802.16d or fixed WiMAX, the user is having a fixed location. This type of user can be a broadband connection to an office or somebody using at home. When a user has a fixed location, it does not require any handovers. All the calls in this case have the same priority and they are temporarily or permanently connected to the network depending upon their required services.

In WiMAX 802.16e or mobile WiMAX, we have a completely different scenario. There are two types of users, fixed and mobile users. In this scenario, user has the liberty to move from one area to another area without the discontinuation of call. Due to the movement of user, handovers are required in this scenario.

As previously discussed, two types of handovers exists which are termed as hard handovers and soft handovers. Soft handovers are fast and they are used in services like GSM and CDMA system. The loss or any kind of delay in data transmission is intolerable in case of voice services. In WiMAX, we use hard handovers. We have both voice and data traffic so we can tolerate some delay or loss of data during the handover. Hard handover are slow when compared to soft handovers. But they are more spectral efficient [1].

4.5 Modulation Scheme in WiMAX

The selection of suitable transmission scheme that includes both modulation and channel access schemes is necessary in concern of RRM. GSM uses TDMA and FDMA while in WLAN utilizes Direct Sequence Spread Spectrum (DSSS). In WiMAX, we use OFDM as the transmission technology. OFDM is one of the most efficient schemes which are available right now [23].

[pic]

Figure 4.3: Adaptive modulation scheme in a cell[24].

In OFDM, the carrier signal is divided into a subset of carrier signals and each signal is transmitted with a different frequency. These different frequencies are orthogonal to each other thus they have minimum interference between them. One of the major advantages of OFDM is that different frequency signals are transmitted by using different modulation schemes. In this scheme, if we have higher SNR, we can use a powerful modulation scheme which has higher data rates. When we have less SNR, we can use a low level modulation scheme with less data rates. Figure 4.2 illustrates this whole mechanism. This method is called adaptive modulation or link adaptation. In WiMAX, we use four different modulation schemes which are BPSK, QPSK, 16-QAM and 64-QAM [23].

Figure 4.4: BPSK constellation diagram [24]. Figure 4.5: QPSK constellation diagram [24].

1. Binary Phase Shift Keying (BPSK)

BPSK is a type of digital modulation. In this scheme, one bit is represented by one symbol and one symbol is equivalent to one phase. It has only two symbols which are ‘0’and ‘1’. In BPSK, we use two different phase signals which are 180 degree out of phase as shown in the Figure 4.3 [24]. BPSK is the most robust modulation technique and it has less error as compared to other phase shift keying schemes.

2. Quadrature Phase Shift Keying (QPSK)

In this scheme, two bits are used to represent one symbol. Hence,we have two bits and total four different phase signals. In the constellation diagram of QPSK, we have four different points as shown in Figure 4.4 [24]. QPSK is more spectral efficient as compared to BPSK but it is less effective against noise.

3. Quadrature Amplitude Modulation (QAM)

The third modulation scheme used in WiMAX is QAM. Here, two different carrier signals which are 180 degree out of phase are used and we vary their amplitudes. QAM has many types which depend on the number of bits used per symbol.

CHAPTER 5

SIMULATION

Introduction

My simulation consists of two parts, the first part is related to link budget while the other is based on cell planning.

1. Link Budget

Link budget is the calculation of the received level of the signal strength by calculating all the gains and losses from the transmitted signal. These gains and losses are introduced in the channel due to air interface, connecting cables etc. I built a MatLab program which can be used to predict and analyze the effects of different losses on the received signal. In Figure 5.1, the flow chart of the process is depicted.

[pic]

Figure 5.1: Flow chart for link budget

I implemented the link budget program in MatLab R2007b. The out put is shown in Figure 5.2.

[pic]

Figure 5.2: Output signals for link budget analysis in communication networks.

Following parameters for link budget are discussed which are also included in it.

• Signal properties and amplitude

• Technology capabilities

• Component capabilities

• Tx/Rx gain

• AWGN noise

• Miscellaneous losses

• Rayleigh fading

• Rain loss

• Path loss

I am taking three frequency bands for WiMAX.

• 2500 MHz

• 3500 MHz

I can change the amplitude of the signal. I have a sinusoidal signal which is plotted in discrete time. The Tx/Rx gain depends on the antennas used, which are shown in drop menu such as,

• Dipole 2 [dBi]

• Biquad 8 [dBi]

• Helix 15 [dBi]

• Parabolic 24 [dBi]

I add AWGN to our original signal with a fixed SNR. Cable losses, connector losses, combiner losses and building losses constitute miscellaneous losses. All losses are taken in [dB].

The Rayleigh fading depends on the speed (km/h) and Doppler frequency shift (Hz). Users moving at different speeds experience different Doppler shifts and hence, different amount of loss caused by Rayleigh fading. The users moving with different speed and their respective Doppler shift is as follows:

• Car 80 km/h 0.074074 Hz

• Pedestrian 4 km/h 8.51852 Hz

• Bicycle 15 km/h 31.9444 Hz

• Fast moving car 120 km/h 255.556 Hz

The rain loss depends on the distance (km). The path loss also depends on the distance and factors such as:

Table 5.1: Environment and path loss exponent

|Environment |Path loss exponent |
|Free Space |2 |
|Urban Area |3.1 |
|Shadowed Urban |4 |
|In Building LOS |1.7 |
|Obstructed in Building |5 |
|Obstructed in Factories |2.5 |

If I want to apply AWGN, rain loss and path loss etc on the original signal, I can see the effects on the resulted signal in Figure 5.2.I also can get output by considering AWGN and so on by taking a digital signal with ASK modulation and then taking FFT of the modulated and demodulated signal and then perform filtering.

5.2 Cell Planning

In RRM context, the field of our core interest is cell planning referred to network coverage and capacity. In cell planning, I have to deal with the issues of number and placement of base stations, nature of radio equipment used and antenna height.

5.2.1 Cell Coverage

My simulation emphasizes on the coverage of the system in general. Path loss is the term which is used to estimate the coverage of a cell. It is the loss in the signal power when it is transmitted through free space. It is the difference between the transmitted power and the received power. Different radio propagation models are adopted to find out the path loss between transmitter and receiver. One of the most commonly used models is free space path loss model. For the estimation of the coverage of a WiMAX network, my simulation will adopt different path loss models.

5.2.1.1 SUI Model

Stanford University Interim (SUI) model is being developed for IEEE 802.16 by the IEEE [28], [29] and [30]. It can be used for frequencies above 1900 MHz. WiMAX will be using frequency band of 3500 MHz so it is a possible solution for WiMAX network coverage.

In this propagation model, I have three different types of terrains or areas. These are called as terrain A, B and C. Terrain A represents an area with highest path loss, it can be a very dense populated region while terrain B represents an area with moderate path loss, it can be a suburban environment. Terrain C has the least path loss which describes a rural or flat area. In Table 5.1, these different terrains and different factors used in SUI model are described.

Table 5.2: Different terrains and parameters [28]

|Parameters |Terrain A |Terrain B |Terrain C |
|a(1/m) |4.6 |4 |3.6 |
|b(1/m) |0.0075 |0.0065 |0.005 |
|c(1/m) |12.6 |17.1 |20 |

The path loss in SUI model can be described as

(5.1)

where

PL = Path Loss in dB

d = distance between the transmitter and receiver

[pic] = 100m used as a reference

[pic] = Correction factor for frequency

[pic] = Correction factor for BS height

S = Shadowing

[pic] = Path loss component and it is described as

[pic] (5.2)

where [pic]is the height of the base station and a, b and c represent the terrain for which the values are selected from the above table.

[pic] (5.3)

where A is free space path loss while [pic] is the distance between Tx and Rx and [pic] is the wavelength. The correction factor for frequency is as follows:

[pic] (5.4)

Here, f is the frequency in MHz. The correction factor BS is given by the following expression:

[pic] (5.5)

where hr is the height of the receiver antenna. This expression is used for terrain type A and B.

[pic] (5.6)

It is used for terrain C.

[pic] (5.7)

Here, [pic]= 5.2 dB for rural and suburban environments (Terrain A & B) and 6.6 dB for urban environment (Terrain C).

In omy calculations, I fixed our carrier frequency at 2500 and 3500 MHz, distance varies from 100m to 50 km, height of receiver is 2m and height of base station is 80m. The numerical results for both urban and rural regions are shown in the Figure 5.3 and Figure 5.4.

[pic]

Figure 5.3: Path loss given by SUI propagation model for 2500 MHz.

[pic]

Figure 5.4: Path loss given by SUI propagation model for 3500 MHz.

5.2.1.2 Ericsson Model

This model is implemented by Ericsson as an extension of the Hata model [29], [30]. In this model, we can adjust the parameters according to the given scenario. The path loss as evaluated by this model is described as

(5.8)

where

(5.9)

The values of[pic],[pic],[pic] and [pic]are constant but they can be changed according to the scenario (environment). The values which I used in our calculations are [pic]= 36.2, [pic]=30.2, [pic]=12.0 and [pic]=0.1. These are the defaults values given by the Ericsson model. The parameter f represents the frequency which is 2500 and 3500 MHz. The base station and receiver heights are same as used earlier. The numerical results for Ericsson model are shown in Figure 5.5 and 5.6.

[pic]

Figure 5.5: Path loss given by Ericsson propagation model for 2500 MHz.

[pic] Figure 5.6: Path loss given by Ericsson propagation model for 3500 MHz.

5.2.1.3 Okumura Model
Okumura model [30] is one of the most commonly used models. It can be used for frequencies up to 3000 MHz. The distance between transmitter and receiver can be around 100 km while the receiver height can be 3 m to 10 m. The path loss in Okumura model can be calculated as πג

(5.10)

Here[pic]is the free space path loss and it is calculated by the following expression: [pic] (5.11) where [pic]and [pic]are heights of BS and receiver receptively while [pic]and[pic]are the BS antenna gain factor and receiver gain factors respectively. Their formulas are as follows:

[pic] (5.12)

[pic] (5.13)

where [pic]is called as median attenuation factor. Different curves for median attenuation factor are used depending on the frequency and the distance between the transmitter and receiver. There are three different types of regions in Okumura model named

Figure 5.7: Median attenuation factor and area gain [1].

open area, quasi–open model and suburban area. The area gain [pic] depends on the area being used and its graph along with median attenuation factor is shown in the below Figure 5.7 [1], [31].

In my calculations,I am using the operating frequency of 2500 MHz, the base station height is 100 m, the height of receiver is 3m and the distance between the transmitter and receiver is 10 km. We determined the path loss for all the different scenarios and it is shown in Figure 5.10.

[pic]

Figure 5.8: Path loss given by Okumura model.

5.2.2 Nominal Cell Site

Besides cell coverage, the nominal cell site is to be determined as a second step. Nominal cell site is more like a mapping of hexagonal cell patterns on the actual geographical map [32]. Above stated propagation model help us estimating the distance between the transmitter and the receiver and finding the path loss correspondingly.I can adjust the cell size according to our requirement. Determination of cell size leads us to generate the hexagonal cells of appropriate size correspondingly. It also guides us for finding an appropriate number of base stations for the coverage of an area optimally. In our simulations, I take a graph for Rajshahi city (Bangladesh) with the help of Google maps and it is shown in Figure 5.9 [33].

[pic]

Figure 5.9: Geographical map of Rajshahi, Bangladesh [33].

[pic]

Figure 5.10: Nominal cell planning of Rajshahi city.

In Figure 5.10, the nominal cell planning of Rajshahi city is shown. The map image is taken from a height of 2000 ft (feet) and it is on the scale of 1 km.I also created the hexagonal cells which have radius slightly less than 1 km.I can have a cell size of 5 km radius but this city has a very large population. Hence,I have to accommodate more users and I have to provide better coverage of the network that is why I have chosen the radius of cell approximately to 2 km. The comparison of different propagation models and their corresponding path losses for the distance of 1 km is shown in Table 5.3. In this table, WiMAX standard equipment powers for the transmitter and receiver are also described. The standard transmitter power of a mobile WiMAX BS for the distance of 1 km is 43 dBm. Similarly, the maximum power that a WiMAX Customer Premises Equipment (CPE) can transmit is 23 dBm.

Table 5.3: Propagation models and their path loss for 1 km [35]

|Propagation Model |Terrain |Frequency Band (MHZ) |Transmitter Power (dBm)|Path Loss (dB) |Receiver Power (dBm) |
|SUI |Urban |2500 |43 |100 |23 |
|SUI |Rural |2500 |43 |82 |23 |
|SUI |Urban |3500 |43 |48 |23 |
|SUI |Rural |3500 |43 |32 |23 |
|Ericsson |Urban |2500 |43 |270 |23 |
|Ericsson |Urban |3500 |43 |272 |23 |
|Okumura |Open |2500 |43 | 36 |23 |
|Okumura |Qausi-open |2500 |43 |42 |23 |
|Okumura |Suburb-an |2500 |43 |55 |23 |

If we want to accommodate more users in a particular cell, we can use sectorization or frequency re-use of a cell.

5.2.3 Site Survey

The site survey is performed at all the base station sites. In site survey,I deal with issues like height of antenna, power availability for equipments and the real estate issues [32].

CHAPTER 6

CONCLUSIONS

6.1 Conclusions

Efficient and optimal utilization of available spectral resources has always been a matter of deep concern for the engineers while designing and implementing cellular networks. While keeping into the consideration, the limited availability of spectral resources, RRM emerges as an extremely important factor in the practical implementation and efficient working of cellular networks. Here I perform for increasing coverage, capacity and QoS but also reduces the installation and operational costs for that network.

I can achieve a good management of radio resources by suggesting and implementing an optimal solution for any of the above mentioned factors. For instance in a WiMAX network,I use OFDM as a transmission technique with BPSK, QPSK, 16- QAM and 64-QAM as modulation techniques in a particular cell depending upon the SNR. Similarly, propagation model with less path loss can be selected.

In my simulation results which have been shown in the previous chapter,I have compared different propagation models for a WiMAX network. On the basis of these numerical results,I can suggest that the SUI model has less path loss as compared to other models. SUI model is shown in Figure 5.5 and 5.6. Okumura model can only be used when we have frequency band of 2500 MHz. But SUI model is used for frequencies up to 3500 MHz (most commonly used frequency band for WiMAX). By using this model, we can calculate the path loss, antenna height and coverage of the cell.

In nominal cell planning, I can map a hexagonal cell structure over the geographical map of any location. The total number of base stations and their exact locations can be specified by nominal cell planning.

The main factors that influence the capacity of the network are available frequency band, cell size, frequency reuse factor etc. In order to increase the capacity of the system, size of the cells is required to be adjusted. Hence, reducing the size of cells helps in the adjustment of the frequency reuse factor.

2. Future Works

In future, my simulated propagation model results can be tested and verified in practical environment. Further study can also be made for a more suitable and optimal propagation model. Also, I can build a software or tool dedicated for cell planning in WiMAX by using the propagation models described in my simulations. I can also add traffic capacity and coverage features in that tool.

APPENDICES

APPENDIX A

Abbreviations and Acronyms

AMPS Advance Mobile Phone Systems

ARQ Automatic Repeat Request

ATM Asynchronous Transfer Mode

AWS Amazon Web Services

BPSK Binary Phase Shift keying

BS Base Station

BSC Base Station Controller

CDMA Code Division Multiple Access

CID Connection Identifier

CPE Customer Premises Equipment

CRC Cyclic Redundancy Check

CSN Connection Service Network
DHCP Dynamic Host Control Protocol
DOCSIS Data over Cable Service Interface Specification

DSL Digital Subscriber Line

EDGE Enhanced Data rates for GSM Evolution

EIR Equipment Identity Register
ETSI European Telecommunications Standard Institute
FDD Frequency Division Duplex

FEC Forward Error Correction

FDMA Frequency Division Multiple Access

FFT Fast Fourier Transform

GPRS General Packet radio Service

GSM Global System for Mobile Communication

GMH Generic MAC Header

HSDPA High Speed Downlink Packet Access

HSUPA High Speed Uplink Packet Access

IP Internet Protocol

ISI Inter Symbol Interference

ITU International Telecommunication Union

LOS Line of Sight

MAC Media Access Control

MIMO Multiple Input Multiple Output

MPDU MAC Protocol Data Units

MS Mobile Station

MSC Master Switching Center

MSDU MAC Service Data Unit

NMT Nordic Mobile Telecommunication System

OFDMA Orthogonal Frequency Division Multiple Access

OFDM Orthogonal Frequency Division Multiplexing

PDA Personal Digital Assistant

PHY Physical Layer

PSTN Public switched Telecommunication Networks

PSH Payload Sub Header

QAM Quadrature Amplitude Modulation

QoS Quality of Service

QPSK Quadrature Phase Shift keying

RRM Radio Resource Management

SIM Subscriber Identity Module

SFID Service Flow Identifier

SH Sub Header

SMS Short Messaging Services

SNR Signal to Noise Ratio

SOFDMA Scalable Orthogonal Frequency Division Multiple Access

TDD Time Division Duplex

TDM Time Division Multiplexing

TDMA Time Division Multiple Access

UARFCN UTRA Absolute Radio Frequency Channel Number

UTRA UMTS Terrestrial Radio Access

UMTS Universal Mobile Telecommunication System

WCDMA Wideband Code Division Multiple Access

WiMAX Worldwide Interoperability for Microwave Access

WLAN Wireless Local Area Network

REFERENCES

1] T.S Rappaport, Wireless Communications: Principles and Practice (2nd edition), Chapter 3, Prentice Hall, Dec 2001.

2] D. Pareek, The Business of WiMAX, Chapter 1, John Wiley, 2006.

3] Fixed, nomadic, portable and mobile applications for 802.16-2004 and 802.16e WiMAX networks, November 2005 (Prepared by Senza Fili, consulting on behalf of the WiMAX Forum). [Online]. Available: http://www.wimaxforum.org/documents/downloads/Applications_for_802.16-2004_and_802.16e_WiMAX_networks_final.pdf [Accessed: Oct. 29.2009].

4] J. G. Andrews, A. Ghosh, R. Muhamed, Fundamentals of WiMAX Understanding Broadband Wireless Networking, Chapter 2, Prentice Hall, 2007.

5] Quality of Service, [Online]. Available: http://www.wimax.com/education/wimax/qos [Accessed: Nov. 17.2009].

6] KAMRAN ETEMAD,CDMA2000 EVOLUTION System Concepts and Design Principles,Chapter 2 & 4, John Wiley Interscience.

7] Radio Resource Management, [Online]. Available: http://en.wikipedia.org/wiki/Radio_Resource_Management [Accessed: Nov. 21.2009].

8] Candian Table of Fequency Allocations 9 kHz to 275 GHz (2005 Edition), May 2005. [Online]. Available:

http://www.ic.gc.ca/epic/site/smt-gst.nsf/vwapj/cane-2006-e.pdf/$FILE/cane-2006-e.pdf, Page 105 [Accessed: Nov. 23.2009].

9] Standardization Sector, [Online]. Available: http://www.itu.int/net/about/itu-t.aspx [Accessed: Nov. 31.2009].

10] UMTS frequency bands, [Online]. Available: http://en.wikipedia.org/wiki/UMTS_frequency_bands [Accessed: Nov. 03.2009].

11] W. Stallings, Wireless Communication and Networking, Chapter 10, Pearson Education, 2006.

12] GSM-bts-walbrzch, [Online]. Available: http://en.wikipedia.org/wiki/Image:Gsm-bts-walbrzych.jpg [Accessed: Nov. 26.2009].

13] Coverage, [Online]. Available: http://www.askcomreg.ie/mobile/coverage.44.LE.asp [Accessed: Nov. 27.2009].

14] Cellular network, [Online]. Available: http://en.wikipedia.org/wiki/Cellular_networks [Accessed: Dec. 12.2009].

15] Site Survey, [Online]. Available: http://en.wikipedia.org/wiki/Image:Gsm-bts-walbrzych.jpg [Accessed: Dec. 15.2009].

16] Site Survey, [Online]. Available: http://www.wimax.com/education/wimax/site_survey [Accessed: Nov. 05.2008].

17] Modulation, [Online]. Available:http://en.wikipedia.org/wiki/Modulation [Accessed: Dec. 25.2009].

18] FDMA, TDMA, CDMA, [Online]. Available:http://www.kn-s.dlr.de/People/Haas/fdma_tdma_cdma.jpg [Accessed: Oct. 29.2009].

19] D. Pareek, The Business of WiMAX, Chapter 2 and Chapter 4, John Wiley, 2006.

20] D. Pareek, A to Z of WiMAX - the Complete Reference, (Kindle Edition), Chapter 10, 2007.

21] Noman shabbir and Hasnain Kashif,RRM in WiMAX,Bleking Institute of Technology,Sweden.

22] Prof. N. Sarkar,Elements of Digital Communication,Chapter 7,Khanna Publishers.

23] D. Pareek, The Business of WiMAX, Chapter 5, John Wiley, 2006.

24] Phase Shift Keying, [Online]. Available:http://en.wikipedia.org/wiki/PSK [Accessed: Nov. 15.2009].

25] IEEE 802.16* and WiMAX, Broadband Wireless Access for Everyone, white paper by Intel.

26] S. Ahson, , M. Ilyas, WiMAX: Applications, Published by CRC Press, 2007

27] L. Nuaymi, WiMAX: Technology for Broadband Wireless Access, John Wiley, 2007.

28] V. Erceg, Channel models for fixed wireless application, Tech. rep. IEEE 802.16 Broadband Wireless Access Working Group, January 2001.

29] Multihop Path Loss Model (Base-to-Relay and Base-to-mobile). 01 May 2006. [Online]. Available:http://www.ieee802.org/16/relay/contrib/C80216j-06_011.pdf [Accessed: Nov. 26.2009].

30] J. Milanovic, S. R. Drlje and K. Bejuk, Comparison of Propagation Models Accuracy for WiMAX on 3.5 GHz, Croatian Telecommunication. Agency, Osijek, Dec. 2007

31] Propagation Models, [Online]. Available: www.mht.bme.hu/~nagy/ea_gsm.ppt [Accessed: Nov. 11.2009].

32] Cell Planning, [Online]. Available: http://cellular-my-reveal.blogspot.com/2007/04/cell-planning.html.[Accessed: Nov. 11.2009].

33] Google Maps, [Online]. Available: http://maps.google.com/maps?hl=en&tab=wl [Accessed: Nov. 29.2009].

34] Hexagonal Graph Paper PDF Generator, [Online]. Available: http://incompetech.com/graphpaper/hexagonal/ [Accessed: Nov. 8.2008].

35] WiMAX Transmission Power, [Online]. Available: http://www.wimaxcom.net/2008/11/wimax-transmit-power.html [Accessed: Dec. 21.2009].

36] Link budget calculator,online available:

http://w3.antd.nist.gov/wctg/manet/prd_linkbudgetcalc.html [Accessed:Jan.17.2010]

37] Simon Haykin,AN INTRODUCTION TO ANALOG & DIGITAL COMMUNICATIONS Chapter 7,J.Wiley.

38] Handoff mechanism in Mobile WiMAX, [Online]. Available: http://www.conniq.com/WiMAX/handoff.htm [Accessed: Oct. 10.2008].

39] FDM,OFDM,OFDMA,SOFDMA,online available: http://images.google.com/imgres?imgurl=http://www.conniq.com/WiMAX/images/OFDMA-PHY.gif&imgrefurl=http://www.conniq.com/WiMAX/fdm-ofdm-ofdma-sofdma-03.

MATLAB Programs for simulation Program 1.Program for link budget analysis in communication network. clc clear n=500; %Number of Random Number m=20; %Number ploted signal ti=1:m*n; time=ti/n; r=randint(1,n); msg=zeros(1,n*n); for i=1:n for j=1:n msg((i-1)*n+j)=r(i); end end subplot(5,2,1) plot(time,msg(1:m*n),'r') grid on axis([0 m -1 2]) title('Message Signal') fc=200; T=1/fc; t=(0:T/n:T-T/n); x=sin(2*pi*fc*t); ask=zeros(1,n*n); for i=1:n for j=1:n ask((i-1)*n+j)=(r(i)+1)*x(j); end end subplot(5,2,3) plot(time,ask(1:m*n)) grid on title('ASK Modulated Signal') fftask=fft(ask); subplot(5,2,4); plot(time,fftask(1:m*n)) grid on title('FFT of the ASK Modulated Signal') awgnask=awgn(ask,15); subplot(5,2,5); plot(time,awgnask(1:m*n)) grid on title('Transmitted Signal through AWGN Channel') fftts=fft(awgnask); subplot(5,2,6); plot(time,fftts(1:m*n)) grid on title('FFT of the Transmitted Signal') dmod=zeros(1,n*n); for i=1:n for j=1:n dmod((i-1)*n+j)=(awgnask(j))*x(i); end end subplot(5,2,7) plot(time,dmod(1:m*n)) grid on title('Demodulated Signal') fftds=fft(dmod); subplot(5,2,8); plot(time,fftds(1:m*n)) grid on title('FFT of the Demodulated Signal') filts=filter(1,1,dmod); subplot(5,2,9); plot(time,filts(1:m*n)) grid on title('Received Signal afrer Filtering')

Program 2.Program for simulation of SUI propagation model for 2500MHz. clc clear d0=100; f=input( 'Enter the value of carrier frequency : '); hb=80; hr=2; %Terrain A/B a=4.6; b=.0075; c=12.6; alpha=5.2; y=a-b*hb+c/hb; A=20*LOG10((4*pi*d0)/(3e8/f)); Xf=6.0*LOG10(f/2000); s=0.65*(LOG10(f))^2-1.3*LOG10(f)+alpha; Xh1=-10.8*LOG10(hr/2000); d1=100:50:50000; PL1=A+10*y*LOG10(d1/d0)+Xf+Xh1+s; %Terrain C a=3.6; b=0.005; c=20; alpha=6.6; y=a-b*hb+c/hb; A=20*LOG10((4*pi*d0)/(3e8/f));
Xf=6.0*LOG10(f/2000);
s=0.65*(LOG10(f))^2-1.3*LOG10(f)+alpha;
Xh2=-20*LOG10(hr/2000);
figure(1) d2=100:50:50000; PL2=A+10*y*LOG10(d2/d0)+Xf+Xh2+s; plot_handles= plot(d1,PL1,'--b',d2,PL2,'--r'); xlabel('Distance Between Tx and Rx (m)') ylabel('Path loss (dB)') grid on title('SUI Propagation Model for 2500 MHz') legend_handles = [plot_handles]; legend(legend_handles,'Urban Areas','Rural Areas')

Program 3.Program for simulation of SUI propagation model for 3500MHz. [Changing input frequency from 2500MHz to 3500MHz and title,program 2 can be use]

Program 4.Program for simulation of Ericsson propagation model for 2500MHz. clc clear f=input( 'Enter the value of carrier frequency : '); hb=80; hr=2; a0=36.2; a1=30.2; a2=12.0; a3=0.1; g(f)=44.49*(LOG10(f))-4.78*(LOG10(f))^2; figure(1) d=100:50:50000; PL=a0+a1*LOG10(d)+a2*LOG10(hb)+(a3*LOG10(hb))*(LOG10(d))- 3.2*(LOG10(11.75*hr))^2+g(f); plot(d,PL) xlabel('Distance Between Tx and Rx (m)') ylabel('Path loss (dB)') grid on title('Ericsson Propagation Model for 2500 MHz')

Program 5.Program for simulation of Ericsson propagation model for 3500MHz. [Changing input frequency from 2500MHz to 3500MHz and title,program 4 can be use]

Program 6.Program for simulation of Okumura propagation model for 2500MHz. clc clear f=input( 'Enter the value of carrier frequency : '); d0=100; A=[20 24 27.5 29 30 31 32 32.5 33 33.5 34]; d=[0 1 2 3 4 5 6 7 8 9 10]; %Open Area Lf=20*LOG10((3e8)./(4.*pi.*d0.*f)); hte=100; hre=3; G(hte)=20.*LOG10(hte./200); G(hre)=10.*LOG10(hre./3); G_ar_1=33.8; PL1=Lf+A-G(hte)-G(hre)-G_ar_1; %Qausi-0pen Area Lf=20.*LOG10((3e8)./(4.*pi.*d0.*f)); hte=100; hre=3; G(hte)=20.*LOG10(hte./200); G(hre)=10.*LOG10(hre./3); G_ar_2=28.1; PL2=Lf+A-G(hte)-G(hre)-G_ar_2; %Suburban Area Lf=20*LOG10((3e8)./(4.*pi.*d0.*f)); hte=100; hre=3; G(hte)=20.*LOG10(hte./200); G(hre)=10.*LOG10(hre./3); G_ar_3=14.2; figure(1) PL3=Lf+A-G(hte)-G(hre)-G_ar_3; plot_handles= plot(d,PL1,'--g',d,PL2,'--r',d,PL3,'--b'); xlabel('Distance Between Tx and Rx (m)') ylabel('Path loss (dB)') grid on title('Okumura Propagation Model for 2500 MHz') legend_handles = [plot_handles]; legend(legend_handles,'Open Area','Qausi-open Area','Suburban Area')

-----------------------

BPSK
2.01 Mbps
SNR = 6 dB

[pic]

[pic]

[pic]

[pic]

LAN

MAN

WAN

PAN

3GPP, EDGE
(GSM)

ETSI
HiperLAN

ETSI
HiperMAN

ETSI HiperPAN

IEEE 802.15*
Bluetooth

IEEE 802.11*

IEEE 802.16*

IEEE 802.20*

[pic]

User 1

User 2

User 3

User 1

User 2

User 3

TCDMA = KT4

T4 = LTCHIP

User 1

User 2

User 3

1 / TCHIP

T4

1 / L

1 / Td

1 / Td